Configuration of Proactive
Operations, Administration, and Maintenance (OAM) Functions for MPLS-Based Transport Networks Using
RSVP-TEEricssonelisa.bellagamba@ericsson.comEricssonattila.takacs@ericsson.comEricssonGregory.Mirsky@ericsson.comHuawei Technologiesloa@mail01.huawei.comAcreo ABElectrum 236Kista164 40Sweden+46 70 7957731pontus.skoldstrom@acreo.seCiscodward@cisco.com
Signaling
CCAMP Working GroupRSVP-TEGMPLSMPLSMPLS-TPOAMThis specification describes the configuration of proactive MPLS
Transport Profile (MPLS-TP) Operations, Administration, and Maintenance (OAM) functions for a given
Label Switched Path (LSP) using a set of TLVs that are carried by the
GMPLS RSVP-TE protocol based on the OAM Configuration Framework for GMPLS RSVP-TE.This document describes the configuration of proactive MPLS-TP OAM functions for a given
LSP using TLVs that use GMPLS RSVP-TE .
defines use of GMPLS RSVP-TE for the configuration of OAM
functions in a technology-agnostic way. This document specifies
the additional mechanisms necessary to establish MPLS-TP
OAM entities at the maintenance points for monitoring and performing
measurements on an LSP, as well as defining information elements and
procedures to configure proactive MPLS-TP OAM functions running between
Label Edge Routers (LERs). Initialization and control of on-demand MPLS-TP OAM functions are
expected to be carried out by directly accessing network nodes via a
management interface; hence, configuration and control of on-demand OAM
functions are out of scope for this document.MPLS-TP, the Transport Profile of MPLS, must, by definition , be
capable of operating without a control plane. Therefore, there are
several options for configuring MPLS-TP OAM without a control plane
by using either a Network Management System (NMS), an LSP Ping, or
signaling protocols such as RSVP-TE in the control plane.
MPLS-TP describes a profile of MPLS that
enables operational models typical in transport networks while providing
additional OAM survivability and other maintenance functions not
currently supported by MPLS. defines the requirements for the
OAM functionality of MPLS-TP.Proactive MPLS-TP OAM is performed by three different protocols:
Bidirectional Forwarding Detection (BFD) for Continuity
Check / Connectivity Verification, the Delay Measurement (DM) protocol
for delay and delay variation (jitter) measurements, and the
Loss Measurement (LM) protocol for packet loss and throughput
measurements. Additionally, there are a number of Fault Management signals
that can be configured .
BFD is a protocol that provides low-overhead, fast detection of
failures in the path between two forwarding engines, including the
interfaces, data link(s), and (to the extent possible) the forwarding
engines themselves. BFD can be used to track the liveliness and to detect
the data plane failures of MPLS-TP point to point and might also be
extended to support point-to-multipoint connections.
The delay and loss measurement protocols use a simple
query/response model for performing bidirectional measurements that allows
the originating node to measure packet loss and delay in both
directions. By timestamping and/or writing current packet counters to the
measurement packets four times (Tx and Rx in both directions), current
delays and packet losses can be calculated. By performing successive delay
measurements, the delay variation (jitter) can be calculated. Current
throughput can be calculated from the packet loss measurements by dividing
the number of packets sent/received with the time it took to perform the
measurement, given by the timestamp in LM header. Combined with a packet
generator, the throughput measurement can be used to measure the maximum
capacity of a particular LSP. It should be noted that here we are not
configuring on-demand throughput estimates based on saturating the
connection as defined in . Rather, we only enable the estimation
of the current throughput based on loss measurements.
AIS - Alarm Indication SignalBFD - Bidirectional Forwarding DetectionCC - Continuity CheckCV - Connectivity VerificationDM - Delay MeasurementFMS - Fault Management Signal G-ACh - Generic Associated ChannelGMPLS - Generalized Multi-Protocol Label SwitchingLDI - Link Down IndicationLER - Label Edge RouterLKR - Lock ReportLM - Loss MeasurementLOC - Loss Of ContinuityLSP - Label Switched PathLSR - Label Switching RouterMEP - Maintenance Entity Group End PointMIP - Maintenance Entity Group Intermediate PointMPLS - Multi-Protocol Label SwitchingMPLS-TP - MPLS Transport ProfileNMS - Network Management SystemPM - Performance MeasurementRSVP-TE - Reservation Protocol Traffic EngineeringTC - Traffic Class
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described
in RFC 2119.
describes how MPLS-TP OAM mechanisms are operated to
meet transport requirements outlined in . specifies two BFD operation modes: 1) "CC mode", which uses
periodic BFD message exchanges with symmetric timer settings supporting
Continuity Check, and 2) "CV/CC mode", which sends unique maintenance entity
identifiers in the periodic BFD messages supporting CV as well as CC. specifies mechanisms for Performance Monitoring of LSPs, in
particular it specifies loss and delay measurement OAM functions. specifies fault management signals with which a server LSP
can notify client LSPs about various fault conditions to suppress alarms
or to be used as triggers for actions in the client LSPs. The following
signals are defined: Alarm Indication Signal (AIS), Link Down Indication
(LDI), and Lock Report (LKR). describes the mapping of fault conditions to
consequent actions. Some of these mappings may be configured by the
operator depending on the application of the LSP. The following defects
are identified: Loss Of Continuity (LOC), Misconnectivity, MEP
Misconfiguration, and Period Misconfiguration. Out of these defect
conditions, the following consequent actions may be configurable: 1)
whether or not the LOC defect should result in blocking the outgoing data
traffic; 2) whether or not the "Period Misconfiguration defect" should
result in a signal fail condition.GMPLS RSVP-TE, or alternatively LSP Ping , can be used to
simply enable the different OAM functions by setting the corresponding
flags in the OAM Function Flags Sub-TLV .
For a more detailed configuration, one
may include sub-TLVs for the different OAM functions in order to specify
various parameters in detail.Typically, intermediate nodes SHOULD NOT process or modify any of
the OAM Configuration TLVs but simply
forward them to the end node. There is one exception to this and that
is if the MPLS OAM FMS Sub-TLV is
present. This sub-TLV MUST be examined even by intermediate nodes that support these extensions
but only acted upon by nodes capable of
transmitting FMS signals into the LSP being established.
The sub-TLV MAY be present when the FMS flag is
set in the OAM Function Flags Sub-TLV. If this sub-TLV is present,
then the "OAM MIP entities desired" and "OAM MEP
entities desired" flags (described in ) in the
LSP Attribute Flags TLV MUST be set and the
entire OAM Configuration TLV placed either in the
LSP_REQUIRED_ATTRIBUTES object or in the LSP_ATTRIBUTES
object in order to ensure that capable intermediate nodes process the
configuration. If placed in the LSP_ATTRIBUTES object, nodes that are not
able to process the OAM Configuration TLV will forward the message without generating an error.
If the MPLS OAM FMS Sub-TLV has been placed in the LSP_REQUIRED_ATTRIBUTES object, a node that
supports RFC 7260 but does not support the MPLS OAM FMS Sub-TLV
MUST generate a PathErr message with "OAM Problem/Configuration Error"
. Otherwise, if the node doesn't support
RFC 7260, it will not raise any errors as described in the Section 4.1
of . Finally, if the MPLS OAM FMS Sub-TLV is not included, only the "OAM MEP
entities desired" flag is set and the OAM Configuration TLV may be
placed in either LSP_ATTRIBUTES or LSP_REQUIRED_ATTRIBUTES. For this specification, BFD MUST be run in either one of the two modes:Asynchronous mode, where both sides should be in active mode;
orUnidirectional mode.In the simplest scenario, RSVP-TE (or alternatively LSP Ping
),
is used only to bootstrap a BFD session for an LSP without any timer negotiation.Timer negotiation can be performed either in subsequent BFD Control
messages (in this case the operation is similar to LSP-Ping-based bootstrapping
described in ) or directly in the RSVP-TE signaling messages.When BFD Control packets are transported in the G-ACh, they are not
protected by any end-to-end checksum; only lower layers are providing
error detection/correction. A single bit error, e.g., a flipped bit in
the BFD State field, could cause the receiving end to wrongly conclude
that the link is down and, in turn, trigger protection switching. To
prevent this from happening, the BFD Configuration Sub-TLV has an
Integrity flag that, when set, enables BFD Authentication using Keyed
SHA1 with an empty key (all 0s) . This would ensure that
every BFD Control packet carries a SHA1 hash of itself that can be used
to detect errors.If BFD Authentication using a pre-shared key / password is desired
(i.e., authentication and not only error detection), the BFD
Authentication Sub-TLV MUST be included in the BFD Configuration
Sub-TLV. The BFD Authentication Sub-TLV is used to specify which
authentication method should be used and which pre-shared key /
password should be used for this particular session. How the key
exchange is performed is out of scope of this document. It is possible to configure Performance Monitoring functionalities such as Loss,
Delay, Delay variation (jitter), and Throughput, as described in
.When configuring Performance Monitoring functionalities, it is
possible to choose either the default configuration (by only setting the
respective flags in the OAM Function Flags Sub-TLV) or a customized
configuration. To customize the configuration, one would set the
respective flags and include the respective Loss and/or Delay
sub-TLVs. By setting the PM/Loss flag in the OAM Function Flags Sub-TLV and
by including the MPLS OAM PM Loss Sub-TLV, one can configure the
measurement interval and loss threshold values for triggering
protection.Delay measurements are configured by setting the PM/Delay flag in the
OAM Function Flags Sub-TLV; by including the MPLS OAM PM Loss
Sub-TLV, one can configure the measurement interval and the delay
threshold values for triggering protection.To configure Fault Management signals and their refresh time, the
FMS flag in the OAM Function Flags Sub-TLV MUST be set and the MPLS
OAM FMS Sub-TLV included. When configuring Fault Management signals,
an implementation can enable the default configuration by setting the
FMS flag in the OAM Function Flags Sub-TLV. In order to modify the
default configuration, the MPLS OAM FMS Sub-TLV MUST be included. If an intermediate point is intended to originate fault management
signal messages, this means that such an intermediate point is
associated with a server MEP through a co-located MPLS-TP client/server
adaptation function, and the "Fault Management subscription" flag in the
MPLS OAM FMS Sub-TLV has been set as an indication of the request to create
the association at each intermediate node of the client LSP. The corresponding
server MEP needs to be configured by its own RSVP-TE session (or, alternatively, via an NMS or
LSP Ping).The OAM Configuration TLV, defined in ,
specifies the OAM functions that are used for the
LSP. This document extends the OAM Configuration TLV by defining a new OAM Type: "MPLS OAM" (3). The
MPLS OAM type is set to request the establishment of OAM functions for
MPLS-TP LSPs. The specific OAM functions are specified in the OAM Function
Flags Sub-TLV as depicted in . When an egress LSR receives an OAM Configuration TLV indicating the
MPLS OAM type, the LSR will first process any present OAM Function Flags Sub-TLV,
and then it MUST process technology-specific configuration TLVs. This
document defines a sub-TLV, the MPLS OAM Configuration Sub-TLV, which
is carried in the OAM Configuration TLV. Type: 33, the MPLS OAM Configuration Sub-TLV.Length: Indicates the total length in octets, including sub-TLVs as well as the Type and Length fields.The following MPLS-OAM-specific sub-TLVs MAY be included in the
MPLS OAM Configuration Sub-TLV:BFD Configuration Sub-TLV MUST be included if either the CC,
the CV, or both OAM Function flags are being set in the
OAM Function Flags Sub-TLV . This sub-TLV carries additional
sub-TLVs; failure to include the correct sub-TLVs MUST result in an
error being generated: "OAM Problem/Configuration Error". The sub-TLVs
are:
BFD Identifiers Sub-TLV MUST always be included.Timer Negotiation Parameters Sub-TLV MUST be included if the N flag is not set.BFD Authentication Sub-TLV MAY be included if the I flag is set.Performance Monitoring Sub-TLV, which MUST be included if any
of the PM/Delay, PM/Loss, or PM/Throughput flags are set in the OAM
Function Flag Sub-TLV . This sub-TLV MAY carry additional sub-TLVs:
MPLS OAM PM Loss Sub-TLV MAY be included if the PM/Loss OAM
Function flag is set. If the MPLS OAM PM Loss Sub-TLV is not
included, default configuration values are used. The same sub-TLV MAY
also be included in case the PM/Throughput OAM Function flag is set
and there is the need to specify measurement intervals different from
the default ones. Since throughput measurements use the same tool as
loss measurements, the same TLV is used.
MPLS OAM PM Delay Sub-TLV MAY be included if the PM/Delay OAM
Function flag is set. If the MPLS OAM PM Delay Sub-TLV is not
included, default configuration values are used.
MPLS OAM FMS Sub-TLV MAY be included if the FMS OAM Function
flag is set. If the MPLS OAM FMS Sub-TLV is not included, default
configuration values are used.
The following are some additional rules of processing the MPLS OAM Configuration Sub-TLV:The MPLS OAM Configuration Sub-TLV MAY be empty, i.e.,
have no Value. If so, then its Length MUST be 8.
Then, all OAM functions that have their corresponding flags
set in the OAM Function Flags Sub-TLV
MUST be assigned their default values or left disabled.A sub-TLV that doesn't have a corresponding flag set MUST be silently ignored.If multiple copies of a sub-TLV are present, then only the first sub-TLV
MUST be used and the remaining sub-TLVs MUST be silently ignored.However, not all the values can be derived from the standard RSVP-TE
objects, in particular the locally assigned Tunnel ID at the egress
cannot be derived by the ingress node. Therefore, the full LSP MEP-ID used
by the ingress has to be carried in the BFD Identifiers Sub-TLV in the
Path message and the egress LSP MEP-ID in the same way in the
Resv message.If the CV flag is set in the OAM Function Flags Sub-TLV ,
then the CC flag MUST be set as well
because performing Connectivity Verification implies performing Continuity Check as well.
The format of an MPLS-TP CV/CC message is shown in . In order to
perform Connectivity Verification, the CV/CC message MUST contain the "LSP MEP-ID"
in addition to the BFD Control packet information. The "LSP MEP-ID" contains four identifiers: MPLS-TP Global_IDMPLS-TP Node IdentifierTunnel_NumLSP_NumThese values need to be correctly set by both ingress and egress when
transmitting a CV packet, and both ingress and egress need to know what
to expect when receiving a CV packet. Most of these values can be derived
from the Path and Resv messages , which use a 5-tuple to
uniquely identify an LSP within an operator's network. This tuple is
composed of a Tunnel Sender Address, Tunnel Endpoint Address, Tunnel_ID,
Extended Tunnel ID, and (GMPLS) LSP_ID.The BFD Configuration Sub-TLV (depicted below) is defined for
BFD-OAM-specific configuration parameters. The BFD Configuration Sub-TLV is
carried as a sub-TLV of the MPLS OAM Configuration Sub-TLV.This TLV accommodates generic BFD OAM information and carries
sub-TLVs.Type: 1, the BFD Configuration Sub-TLV.Length: Indicates the total length in octets, including sub-TLVs as well as the Type and Length fields.Version: Identifies the BFD protocol version. If the egress LSR does not
support the version, an error MUST be generated: "OAM Problem/Unsupported BFD
Version".BFD Negotiation (N): If set timer negotiation/re-negotiation via
BFD Control messages is enabled, when cleared it is disabled.Symmetric Session (S): If set, the BFD session MUST use symmetric
timing values. Integrity (I): If set, BFD Authentication MUST be enabled. If the BFD
Configuration Sub-TLV does not include a BFD Authentication Sub-TLV, the
authentication MUST use Keyed SHA1 with an empty pre-shared key (all
0s). If the egress LSR does not support BFD Authentication, an error MUST
be generated: "OAM Problem/BFD Authentication unsupported".Encapsulation Capability (G): If set, it shows the capability of
encapsulating BFD messages into The G-Ach channel. If both the G bit and
U bit are set, configuration gives precedence to the G bit. If the
egress LSR does not support any of the ingress LSR Encapsulation
Capabilities, an error MUST be generated: "OAM Problem/Unsupported
BFD Encapsulation format". Encapsulation Capability (U): If set, it shows the capability of
encapsulating BFD messages into UDP packets. If both the G bit and U
bit are set, configuration gives precedence to the G bit. If the
egress LSR does not support any of the ingress LSR Encapsulation
Capabilities, an error MUST be generated: "OAM Problem/Unsupported
BFD Encapsulation Format".Bidirectional (B): If set, it configures BFD in the Bidirectional mode.
If it is not set, it configures BFD in unidirectional mode. In the second case,
the source node does not expect any Discriminator values back from the destination node.Reserved: Reserved for future specifications; set to 0 on transmission and ignored when received.The BFD Configuration Sub-TLV MUST include the following sub-TLVs in
the Path message:BFD Identifiers Sub-TLV; andNegotiation Timer Parameters Sub-TLV if the N flag is
cleared.The BFD Configuration Sub-TLV MUST include the following sub-TLVs in
the Resv message:BFD Identifiers Sub-TLV; andNegotiation Timer Parameters Sub-TLV if:
the N and S flags are cleared; or if the N flag is cleared and the S flag is set and the
Negotiation Timer Parameters Sub-TLV received by
the egress contains unsupported values. In this case, an updated
Negotiation Timer Parameters Sub-TLV
containing values supported by the egress LSR MUST be returned to the ingress.The BFD Identifiers Sub-TLV is carried as a sub-TLV of the
BFD Configuration Sub-TLV and is depicted below.Type: 1, the BFD Identifiers Sub-TLV.Length: Indicates the TLV total length in octets, including the Type and Length fields (20).Local Discriminator: A unique, non-zero discriminator value
generated by the transmitting system and referring to itself; it is used to
de-multiplex multiple BFD sessions between the same pair of
systems as defined in .MPLS-TP Global_ID, Node Identifier, Tunnel_Num,
and LSP_Num: All set as defined in .The Negotiation Timer Parameters Sub-TLV is carried as a sub-TLV
of the BFD Configuration Sub-TLV and is depicted below.Type: 2, the Negotiation Timer Parameters Sub-TLV.Length: Indicates the TLV total length in octets, including Type and Length fields (16).Acceptable Min. Asynchronous TX interval: If the S flag
is set in the BFD Configuration Sub-TLV, it expresses the desired
time interval (in microseconds) at which the ingress LER intends to
both transmit and receive BFD periodic control packets. If the egress
LSR cannot support the value, it SHOULD reply with a supported
interval.If the S flag is cleared in the BFD Configuration
Sub-TLV, this field expresses the desired time interval (in
microseconds) at which the ingress LSR intends to transmit BFD periodic
control packets.Acceptable Min. Asynchronous RX interval: If the S
flag is set in the BFD Configuration Sub-TLV, this field MUST be set equal to
"Acceptable Min. Asynchronous TX interval" on transmit and MUST be ignored
on receipt since it has no additional
meaning with respect to the one described for "Acceptable Min. Asynchronous
TX interval".If the S flag is cleared in the BFD Configuration
Sub-TLV, it expresses the minimum time interval (in microseconds) at
which the ingress/egress LSRs can receive periodic BFD Control
packets. If this value is greater than the "Acceptable
Min. Asynchronous TX interval" received from the ingress/egress LSR,
the receiving LSR MUST adopt the interval expressed in the "Acceptable
Min. Asynchronous RX interval".Required Echo TX Interval: The minimum interval (in microseconds)
between received BFD Echo packets that this system is capable of
supporting, less any jitter applied by the sender as described in
Section 6.8.9 of . This value is also an indication for the
receiving system of the minimum interval between transmitted BFD Echo
packets. If this value is zero, the transmitting system does not
support the receipt of BFD Echo packets. If the LSR node cannot
support this value, it SHOULD reply with a supported value (which may
be zero if Echo is not supported).The BFD Authentication Sub-TLV is carried as a sub-TLV of the
BFD Configuration Sub-TLV and is depicted below.Type: 3, the BFD Authentication Sub-TLV.Length: Indicates the TLV total length in octets, including Type and Length fields (8).Auth Type: Indicates which type of authentication to use. The same
values are used as are defined in Section 4.1 of . If the
egress LSR does not support this type, an "OAM Problem/Unsupported
BFD Authentication Type" error MUST be generated.Auth Key ID: Indicates which authentication key or password
(depending on Auth Type) should be used. How the key exchange is
performed is out of scope of this document. If the egress LSR does
not support this Auth Key ID, an "OAM Problem/Mismatch of BFD
Authentication Key ID" error MUST be generated. Reserved: Reserved for future specifications; set to 0 on
transmission and ignored when received.The Traffic Class Sub-TLV is carried as a sub-TLV of the
BFD Configuration Sub-TLV or Fault Management Signal Sub-TLV ()
and is depicted in .Type: 4, the Traffic Class Sub-TLV.Length: Indicates the length of the Value field in octets (4).Traffic Class (TC): Identifies the TC for periodic
continuity monitoring messages or packets with fault
management information.If the Traffic Class Sub-TLV is present, then the value of the TC field MUST be used
as the value of the TC field of an MPLS label stack entry. If the
Traffic Class Sub-TLV is absent
from BFD Configuration Sub-TLV or Fault Management Signal Sub-TLV, then selection of
the TC value is a local decision.
If the OAM Function Flags Sub-TLV has either the PM/Loss, PM/Delay,
or PM/Throughput flag set, the Performance Monitoring Sub-TLV MUST be
present in the MPLS OAM Configuration Sub-TLV. Failure to include the
correct sub-TLVs MUST result in an "OAM Problem/Configuration Error" message
being generated.The Performance Monitoring Sub-TLV provides the configuration information mentioned in Section 7 of
. It includes support for the configuration of
quality thresholds and, as described in , "the
crossing of which will trigger warnings or alarms, and result reporting and exception notification will be
integrated into the system-wide network management and reporting framework."In case the values need to be different than the default ones, the
Performance Monitoring Sub-TLV includes the following sub-TLVs:
MPLS OAM PM Loss Sub-TLV if the PM/Loss and/or PM/Throughput flag is set in the OAM
Function Flags Sub-TLV; andMPLS OAM PM Delay Sub-TLV if the PM/Delay flag is set in the
OAM Function Flags Sub-TLV.The Performance Monitoring Sub-TLV depicted below is carried as a
sub-TLV of the MPLS OAM Configuration Sub-TLV.Type: 2, the Performance Monitoring Sub-TLV.Length: Indicates the TLV total length in octets, including sub-TLVs as well as Type and Length fields. Configuration Flags (for the specific function description please refer to ):
D: Delay inferred/direct (0=INFERRED, 1=DIRECT). If the egress LSR does
not support the specified mode, an "OAM Problem/Unsupported Delay Mode" error MUST be generated.L: Loss inferred/direct (0=INFERRED, 1=DIRECT). If the egress LSR does
not support the specified mode, an "OAM Problem/Unsupported Loss Mode" error MUST be generated.J: Delay variation/jitter (1=ACTIVE, 0=NOT ACTIVE). If the egress LSR does
not support Delay variation measurements and the J flag is set, an
"OAM Problem/Delay variation unsupported" error MUST be generated.Y: Dyadic (1=ACTIVE, 0=NOT ACTIVE). If the egress LSR does
not support Dyadic mode and the Y flag is set, an
"OAM Problem/Dyadic mode unsupported" error MUST be generated.K: Loopback (1=ACTIVE, 0=NOT ACTIVE). If the egress LSR does
not support Loopback mode and the K flag is set, an
"OAM Problem/Loopback mode unsupported" error MUST be generated.C: Combined (1=ACTIVE, 0=NOT ACTIVE). If the egress LSR does
not support Combined mode and the C flag is set, an
"OAM Problem/Combined mode unsupported" error MUST be generated.Reserved: Reserved for future specifications; set to 0 on transmission and ignored when received.The MPLS OAM PM Loss Sub-TLV depicted below is carried as a
sub-TLV of the Performance Monitoring Sub-TLV.Type: 1, the MPLS OAM PM Loss Sub-TLV.Length: Indicates the length of the parameters in octets, including Type and Length fields (20).Origin Timestamp Format (OTF): Origin Timestamp Format of the Origin Timestamp field
described in . By default, it is set to IEEE 1588 version
1. If the egress LSR cannot support this value, an "OAM
Problem/Unsupported Timestamp Format" error MUST be generated. Configuration Flags (please refer to for further details):
T: Traffic-class-specific measurement indicator. Set to 1 when
the measurement operation is scoped to packets of a particular
traffic class (Differentiated Service Code Point (DSCP) value) and zero otherwise. When set to 1, the
Differentiated Services (DS) field of the message indicates the measured traffic class.
By default, it is set to 1.B: Octet (byte) count. When set to 1, it indicates that the Counter
1-4 fields represent octet counts. When set to 0, it indicates that
the Counter 1-4 fields represent packet counts.
By default, it is set to 0.Reserved: Reserved for future specifications; set to 0 on transmission and ignored when received.Measurement Interval: The time interval (in milliseconds) at
which Loss Measurement query messages MUST be
sent in both directions. If the egress LSR cannot support the value, it SHOULD reply with a supported
interval. By default, it is set to 100 milliseconds as per .Test Interval: Test messages interval (in milliseconds) as
described in .
By default, it is set to 10 milliseconds as per . If
the egress LSR cannot support the value, it SHOULD reply with a
supported interval.Loss Threshold: The threshold value of measured lost packets per measurement over which action(s)
SHOULD be triggered. The MPLS OAM PM Delay Sub-TLV depicted below is carried as a
sub-TLV of the Performance Monitoring Sub-TLV.Type: 2, the MPLS OAM PM Delay Sub-TLV.Length: Indicates the length of the parameters in octets, including Type and Length fields (20).OTF: Origin Timestamp Format of the Origin Timestamp field
described in .
By default, it is set to IEEE 1588 version 1. If the egress LSR
cannot support this value, an "OAM Problem/Unsupported Timestamp Format" error
MUST be generated. Configuration Flags (please refer to for further details):
T: Traffic-class-specific measurement indicator. Set to 1 when
the measurement operation is scoped to packets of a particular
traffic class (Differentiated Services Code Point (DSCP) value) and zero otherwise. When set to 1, the
Differentiated Service (DS) field of the message indicates the measured traffic class.
By default, it is set to 1.B: Octet (byte) count. When set to 1, it indicates that the Counter
1-4 fields represent octet counts. When set to 0, it indicates that
the Counter 1-4 fields represent packet counts.
By default, it is set to 0.Reserved: Reserved for future specifications; set to 0 on transmission and ignored when received.Measurement Interval: The time interval (in milliseconds) at
which Delay Measurement query messages MUST be
sent on both directions. If the egress LSR cannot support the value,
it SHOULD reply with a supported interval. By
default, it is set to 1000 milliseconds as per .Test Interval: Test messages interval (in milliseconds) as
described in .
By default, it is set to 10 milliseconds as per . If
the egress LSR cannot support the value, it SHOULD reply with a supported interval.Delay Threshold: The threshold value of measured two-way delay (in milliseconds) over which action(s)
SHOULD be triggered. The MPLS OAM FMS Sub-TLV depicted below is carried as a sub-TLV of
the MPLS OAM Configuration Sub-TLV. When both working and protection paths
are signaled, both LSPs SHOULD be signaled with identical settings of
the E flag, T flag, and the refresh timer.Type: 3, the MPLS OAM FMS Sub-TLV.Length: Indicates the TLV total length in octets, including Type and Length fields (8).FMS Signal Flags are used to enable the FMS signals at MEPs and
the server MEPs of the links over which the LSP is forwarded. In this
document, only the S flag pertains to server MEPs. The following flags are defined:
E: Enable Alarm Indication Signal (AIS) and Lock Report (LKR) signaling
as described in . The default value is 1
(enabled). If the egress MEP does not support FMS signal
generation, an "OAM Problem/Fault management signaling unsupported" error MUST be generated. S: Indicate to a server MEP that it should transmit AIS and LKR signals on
client LSPs. The default value is 0 (disabled). If a server MEP, which is capable of
generating FMS messages, is for some
reason unable to do so for the LSP being signaled an "OAM Problem/Unable to
create fault management association" error MUST be generated. T: Set timer value, enabled by the configuration of a specific timer value.
The Default value is 0 (disabled).Remaining bits: Reserved for a future specification and set to 0.Refresh Timer: Indicates (in seconds) the refresh timer of fault indication messages. The value MUST be
between 1 to 20 seconds as specified for the Refresh Timer field in
. If the egress LSR cannot support
the value, it SHOULD reply with a supported timer value. The Fault Management Signals Sub-TLV MAY include the Traffic Class Sub-TLV (.) If the Traffic Class Sub-TLV is present,
the value of the TC field MUST be used as the value of the TC field of an MPLS label stack entry
for FMS messages. If the Traffic Class Sub-TLV is absent, then
selection of the TC value is local decision.In addition to error values specified in , this document
defines the following values for the "OAM Problem" error code: If an egress LSR does not support the specified BFD version, an
error MUST be generated: "OAM Problem/Unsupported BFD Version".If an egress LSR does not support the specified BFD Encapsulation
format, an error MUST be generated: "OAM Problem/Unsupported BFD Encapsulation format".If an egress LSR does not support BFD Authentication and it is requested,
an error MUST be generated: "OAM Problem/BFD Authentication unsupported".If an egress LSR does not support the specified BFD Authentication Type,
an error MUST be generated: "OAM Problem/Unsupported BFD Authentication Type".If an egress LSR is not able to use the specified Authentication Key ID, an
error MUST be generated: "OAM Problem/Mismatch of BFD Authentication Key ID".If an egress LSR does not support the specified Timestamp Format,
an error MUST be generated: "OAM Problem/Unsupported Timestamp
Format".If an egress LSR does not support the specified Delay mode, an "OAM
Problem/Unsupported Delay Mode" error MUST be generated.If an egress LSR does not support the specified Loss mode, an "OAM
Problem/Unsupported Loss Mode" error MUST be generated.If an egress LSR does not support Delay variation measurements and it
is requested, an "OAM Problem/Delay variation unsupported" error MUST
be generated.If an egress LSR does not support Dyadic mode and it is requested, an
"OAM Problem/Dyadic mode unsupported" error MUST be generated.If an egress LSR does not support Loopback mode and it is requested, an
"OAM Problem/Loopback mode unsupported" error MUST be generated.If an egress LSR does not support Combined mode and it is requested, an
"OAM Problem/Combined mode unsupported" error MUST be generated.If an egress LSR does not support Fault Monitoring signals and it is requested, an
"OAM Problem/Fault management signaling unsupported" error MUST be generated.If an intermediate server MEP supports Fault Monitoring signals
but is unable to create an association
when requested to do so, an "OAM Problem/Unable to create fault
management association" error MUST be generated.This document specifies the new MPLS OAM type.
IANA has allocated a new type (3) from the
"OAM Types" space of the "RSVP-TE OAM Configuration Registry".
TypeDescriptionReference3MPLS OAM[RFC7487]This document specifies the MPLS OAM Configuration Sub-TLV. IANA has
allocated a new type (33) from the OAM Sub-TLV space of the
"RSVP-TE OAM Configuration Registry".
TypeDescriptionReference33MPLS OAM Configuration Sub-TLV[RFC7487]IANA has created an "MPLS OAM Configuration Sub-TLV Types" sub-registry in the
"RSVP-TE OAM Configuration Registry" for the sub-TLVs carried in
the MPLS OAM Configuration Sub-TLV. Values from this new
sub-registry are to be
allocated through IETF Review except for the "Reserved for Experimental Use" range.
This document defines the
following types:TypeDescriptionReference0Reserved[RFC7487]1BFD Configuration Sub-TLV[RFC7487]2Performance Monitoring Sub-TLV[RFC7487]3MPLS OAM FMS Sub-TLV[RFC7487]4-65532Unassigned65533-65534Reserved for Experimental Use[RFC7487]65535Reserved[RFC7487]IANA has created a "BFD Configuration Sub-TLV Types" sub-registry in the
"RSVP-TE OAM Configuration Registry" for the sub-TLV types carried in
the BFD Configuration Sub-TLV. Values from this new sub-registry
are to be
allocated through IETF Review except for the "Reserved for Experimental Use" range.
This document defines the following
types:TypeDescriptionReference0Reserved[RFC7487]1BFD Identifiers Sub-TLV[RFC7487]2Negotiation Timer Parameters Sub-TLV[RFC7487]3BFD Authentication Sub-TLV[RFC7487]4Traffic Class Sub-TLV[RFC7487]5-65532Unassigned65533-65534Reserved for Experimental Use[RFC7487]65535Reserved[RFC7487]IANA has created a "Performance Monitoring Sub-TLV Type" sub-registry in the
"RSVP-TE OAM Configuration Registry" for the sub-TLV types carried in
the Performance Monitoring Sub-TLV. Values from this new
sub-registry are to be
allocated through IETF Review except for the "Reserved for Experimental Use" range.
This document defines the following
types:TypeDescriptionReference0Reserved[RFC7487]1MPLS OAM PM Loss Sub-TLV[RFC7487]2MPLS OAM PM Delay Sub-TLV[RFC7487]3-65532Unassigned65533-65534Reserved for Experimental Use[RFC7487]65535Reserved[RFC7487]The following values have been assigned under the "OAM Problem" error
code by IETF Review process:Error Value Sub-CodesDescriptionReference13Unsupported BFD Version[RFC7487]14Unsupported BFD Encapsulation format[RFC7487]15Unsupported BFD Authentication Type[RFC7487]16Mismatch of BFD Authentication Key ID[RFC7487]17Unsupported Timestamp Format[RFC7487]18Unsupported Delay Mode[RFC7487]19Unsupported Loss Mode[RFC7487]20Delay variation unsupported[RFC7487]21Dyadic mode unsupported[RFC7487]22Loopback mode unsupported[RFC7487]23Combined mode unsupported[RFC7487]24Fault management signaling unsupported[RFC7487]25Unable to create fault management association[RFC7487]
The "Sub-Codes - 40 OAM Problem" sub-registry is located in the "Error Codes and Globally-Defined Error Value Sub-Codes" registry.
The signaling of OAM-related parameters and the automatic establishment
of OAM entities introduces additional security considerations to those
discussed in . In particular, a network element could be
overloaded if an attacker were to request high frequency liveliness
monitoring of a large number of LSPs, targeting a single network element
as discussed in and .Additional discussion of security for MPLS and GMPLS protocols can be found in .
Key words for use in RFCs to Indicate Requirement LevelsGeneralized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) ExtensionsRequirements of an MPLS Transport ProfileRequirements for Operations, Administration, and Maintenance (OAM) in MPLS Transport NetworksBidirectional Forwarding Detection (BFD)Bidirectional Forwarding Detection (BFD) for MPLS Label Switched Paths (LSPs)MPLS Transport Profile (MPLS-TP) IdentifiersPacket Loss and Delay Measurement for MPLS NetworksMPLS Fault Management Operations, Administration, and Maintenance (OAM)Proactive Connectivity Verification, Continuity Check, and Remote Defect Indication for the MPLS Transport ProfileGeneralized Multiprotocol Label Switching (GMPLS) Control of Ethernet Provider Backbone Traffic Engineering (PBB-TE)GMPLS RSVP-TE Extensions for Operations, Administration, and Maintenance (OAM) ConfigurationOperations, Administration, and Maintenance Framework for MPLS-Based Transport NetworksA Packet Loss and Delay Measurement Profile for MPLS-Based Transport NetworksSecurity Framework for MPLS and GMPLS NetworksMultiprotocol Label Switching (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" FieldConfiguration of Proactive Operations, Administration, and Maintenance
(OAM) Functions for MPLS-based Transport Networks using LSP PingEricssonEricssonHuawei TechnologiesAcreoCiscoJuniperThe authors would like to thank David Allan, Lou Berger, Annamaria
Fulignoli, Eric Gray, Andras Kern, David Jocha, and David Sinicrope
for their useful comments.This document is the result of a large team of authors and
contributors. The following is a list of the contributors:John DrakeBenoit Tremblay