Network Working Group
Internet Engineering Task Force (IETF)                          Z. Zhang
Internet-Draft
Request for Comments: 8502                        Juniper Networks, Inc.
Intended status:
Category: Standards Track                                     H. Tsunoda
Expires: March 11, 2019
ISSN: 2070-1721                           Tohoku Institute of Technology
                                                      September 07,
                                                           December 2018

                         L2L3 VPN Multicast MIB
                 draft-ietf-bess-l2l3-vpn-mcast-mib-16

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes two MIB modules which that will be used by
   other MIB modules for monitoring and/or configuring Layer 2 and Layer
   3 Virtual Private Networks that support multicast.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list  It represents the consensus of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid the IETF community.  It has
   received public review and has been approved for a maximum publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of six months RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 11, 2019.
   https://www.rfc-editor.org/info/rfc8502.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info)
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  The Internet-Standard Management Framework  . . . . . . . . .   4   3
   3.  Summary of MIB Modules  . . . . . . . . . . . . . . . . . . .   4
   4.  Definitions . . . . . . . . . . . . . . . . . . . . . . . . .   4
     4.1.  L2L3-VPN-MULTICAST-TC-MIB Object Definitions  . . . . . .   4
     4.2.  L2L3-VPN-MULTICAST-MIB Object Definitions . . . . . . . .   9   8
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  15
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  16
   7.  Acknowledgement  References  . . . . . . . . . . . . . . . . . . . . . . . . .  17
   8.
     7.1.  Normative References  . . . . . . . . . . . . . . . . . .  17
     7.2.  Informative References  . . . . . . .  17
     8.1.  Normative References  . . . . . . . . . . .  19
   Acknowledgements  . . . . . . .  17
     8.2.  Informative References . . . . . . . . . . . . . . . . .  19
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  20  19

1.  Introduction

   In BGP/MPLS Virtual Private Networks (VPNs), the Border Gateway
   Protocol (BGP) is used for distributing routes and MultiProtocol Multiprotocol
   Label Switching (MPLS) is used for forwarding packets across service
   provider networks.

   The procedures for supporting multicast in a BGP/MPLS Layer 3 (L3)
   VPN are specified in [RFC6513].  The procedures for supporting
   multicast in a BGP/MPLS Layer 2 (L2) VPN are specified in [RFC7117].
   Throughout this document, we will use the term "L2L3VpnMCast network"
   to mean a BGP/MPLS L2 and L3 VPN that support supports multicast.

   L2L3VpnMCast networks use various transport mechanisms for forwarding
   a packet to all or a subset of Provider Edge (PE) routers (PEs) across
   service provider networks.  These transport mechanisms are abstracted
   as provider tunnels (P-tunnels).  The type of a P-tunnel indicates the
   type of the tunneling technology used to establish the P-tunnel.  The
   syntax and semantics of a Tunnel identifier is Identifier are determined by the
   corresponding P-tunnel type [RFC6514].  The P-tunnel type and
   P-tunnel identifier together identify a P-tunnel.

   A BGP attribute that specifies information of a P-tunnel is called a
   Provider Multicast Service Interface (PMSI) tunnel Tunnel attribute.  The
   PMSI tunnel Tunnel attribute is advertised/received by PEs in BGP auto-
   discovery (A-D) routes.  [RFC6514] defines the format of a PMSI
   tunnel
   Tunnel attribute.  The P-tunnel type and the P-tunnel identifier are
   included in the corresponding PMSI tunnel Tunnel attribute.

   This document describes textual conventions (TCs) and common managed
   objects (MOs) which that will be used by other Management Information Base
   (MIB) modules for monitoring and/or configuring L2L3VpnMCast
   networks.

   This document defines two TCs to represent

   (a) the type of a P-tunnel and
   (b) the identifier of a P-tunnel

   respectively.

   The document also defines MOs that will provide the information
   contained in a PMSI tunnel Tunnel attribute and corresponding P-tunnel
   information. P-tunnel.

1.1.  Terminology

   This document adopts the definitions, acronyms acronyms, and mechanisms
   described in [RFC6513] [RFC6514] [RFC7117] and other documents that
   they refer to.  Familiarity with Multicast, multicast, MPLS, Layer 3 VPN, and
   Multicast VPN concepts and/or mechanisms is assumed.  Some terms
   specifically related to this document are explained below.

   "Provider Multicast Service Interface (PMSI)"

   PMSI [RFC6513] is a conceptual interface instantiated by a P-tunnel,
   which is a transport mechanism used to deliver multicast traffic.  A
   PE uses it to send customer multicast traffic to all or some PEs in
   the same VPN.

   There are two kinds of PMSIs: "Inclusive Inclusive PMSI (I-PMSI)" (I-PMSI) and
   "Selective Selective
   PMSI (S-PMSI)" (S-PMSI) [RFC6513].  An I-PMSI is a PMSI that enables a PE
   attached to a particular Multicast VPN to transmit a message to all
   PEs in the same VPN.  An S-PMSI is a PMSI that enables a PE attached
   to a particular Multicast VPN to transmit a message to some of the
   PEs in the same VPN.

   Throughout this document, we will use the term "PMSI" to refer to
   both "I-PMSI" and "S-PMSI." "S-PMSI".

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

3.  Summary of MIB Modules

   This document defines two MIB modules: L2L3-VPN-MULTICAST-TC-MIB and
   L2L3-VPN-MULTICAST-MIB.

   o  L2L3-VPN-MULTICAST-TC-MIB contains two Textual Conventions: textual conventions:
      L2L3VpnMcastProviderTunnelType and L2L3VpnMcastProviderTunnelId.
      L2L3VpnMcastProviderTunnelType provides an enumeration of the
      P-tunnel types.  L2L3VpnMcastProviderTunnelId represents an
      identifier of a P-tunnel.

   o  L2L3-VPN-MULTICAST-MIB defines a table the following table:
      l2L3VpnMcastPmsiTunnelAttributeTable.  An entry in this table
      corresponds to the attribute information of a specific P-tunnel on
      a PE router.  Entries in this table will be used by other MIB
      modules for monitoring and/or configuring an L2L3VpnMCast network.
      The table index uniquely identifies a P-tunnel.  It is composed of
      a type and identifier of a P-tunnel.  The table may also be used
      in conjunction with other MIBs, such as the MPLS Traffic
      Engineering MIB (MPLS-TE-STD-MIB) [RFC3812], to obtain further
      information about a P-tunnel.  It may also be used in conjunction
      with the Interfaces Group MIB (IF-MIB) [RFC2863] to obtain further
      information about the interface corresponding to a P-tunnel.

4.  Definitions

4.1.  L2L3-VPN-MULTICAST-TC-MIB Object Definitions

   This MIB module makes reference to the following documents:
   [RFC4875], [RFC5015], [RFC6388], [RFC7524], and [RFC7761].

    L2L3-VPN-MULTICAST-TC-MIB DEFINITIONS ::= BEGIN

    IMPORTS
      MODULE-IDENTITY, mib-2
         FROM SNMPv2-SMI                            -- [RFC2578] RFC 2578

      TEXTUAL-CONVENTION
         FROM SNMPv2-TC;                            -- [RFC2579] RFC 2579

    l2L3VpnMcastTCMIB MODULE-IDENTITY
      LAST-UPDATED "201809071200Z" "201812140000Z"  -- 7th September, 14 December 2018
      ORGANIZATION "IETF BESS Working Group." Group"
      CONTACT-INFO
          "        Zhaohui
                    "Zhaohui Zhang
                     Juniper Networks, Inc.
                     10 Technology Park Drive
                     Westford, MA 01886
                   USA
                     United States of America
                     Email: zzhang@juniper.net

                     Hiroshi Tsunoda
                     Tohoku Institute of Technology
                     35-1, Yagiyama Kasumi-cho
                     Taihaku-ku, Sendai, 982-8577
                     Japan
                     Email: tsuno@m.ieice.org

                   Comments and discussion to bess@ietf.org
          " tsuno@m.ieice.org"

      DESCRIPTION
          "This MIB module specifies textual conventions for
           Border Gateway Protocol/MultiProtocol Protocol/Multiprotocol Label
           Switching Layer 2 and Layer 3 Virtual Private Networks
           that support multicast (L2L3VpnMCast networks).

           Copyright (C) The Internet Society (2018). (c) 2018 IETF Trust and the persons identified
           as authors of the code.  All rights reserved.

           Redistribution and use in source and binary forms, with or
           without modification, is permitted pursuant to, and subject
           to the license terms contained in, the Simplified BSD
           License set forth in Section 4.c of the IETF Trust's Legal
           Provisions Relating to IETF Documents
           (http://trustee.ietf.org/license-info).
          "

      -- Revision history. History

      REVISION "201809071200Z" "201812140000Z"  -- 7th September, 14 December 2018
      DESCRIPTION
          "Initial version, published as RFC XXXX."

    -- RFC Ed.: replace XXXX with actual RFC number and remove this note 8502."

      ::= { mib-2 AAAA 244 }

    -- IANA Reg.: Please assign a value for "AAAA" under the
    -- 'mib-2' subtree and record the assignment in the SMI
    -- Numbers registry.

    -- RFC Ed.: When the above assignment has been made, please
    -- remove the above note
    -- replace "AAAA" here with the assigned value and
    -- remove this note.

  -- Textual convention Convention

    L2L3VpnMcastProviderTunnelType ::= TEXTUAL-CONVENTION
      STATUS       current
      DESCRIPTION
          "This textual convention enumerates values
           representing the type of a provider tunnel (P-tunnel)
           used for L2L3VpnMCast networks.
           These labeled numbers are aligned with the definition
           of Tunnel types Types in Section 5 of [RFC6514] RFC 6514 and
           Section 14.1 of [RFC7524]. RFC 7524.

           The enumerated values and the corresponding P-tunnel types
           are as follows:

            noTunnelInfo       (0) : no No tunnel information present
                                                        [RFC6514] RFC 6514
            rsvpP2mp           (1) : RSVP-TE P2MP LSP    [RFC4875]      RFC 4875
            ldpP2mp            (2) : mLDP P2MP LSP       [RFC6388]         RFC 6388
            pimSsm             (3) : PIM-SSM Tree        [RFC7761]          RFC 7761
            pimAsm             (4) : PIM-SM Tree         [RFC7761]           RFC 7761
            pimBidir           (5) : BIDIR-PIM Tree      [RFC5015]        RFC 5015
            ingressReplication (6) : Ingress Replication [RFC6513]   RFC 6513
            ldpMp2mp           (7) : mLDP MP2MP LSP      [RFC6388]        RFC 6388
            transportTunnel    (8) : Transport Tunnel    [RFC7524]      RFC 7524

           These numbers are registered at IANA.
           A current list of assignments can be found at
          <https://www.iana.org/assignments/bgp-parameters/
           bgp-parameters.xhtml#pmsi-tunnel-types>.
           <https://www.iana.org/assignments/bgp-parameters/>.
          "
      REFERENCE
        "RFC4875
         RFC5015
         RFC6388
         RFC6513
         RFC6514,
          "RFC 4875
           RFC 5015
           RFC 6388
           RFC 6513
           RFC 6514, Section 5
         RFC7524,
           RFC 7524, Section 14.1
         RFC7761
           RFC 7761
          "

      SYNTAX       INTEGER
           {
             noTunnelInfo       (0),
             rsvpP2mp           (1),
             ldpP2mp            (2),
             pimSsm             (3),
             pimAsm             (4),
             pimBidir           (5),
             ingressReplication (6),
             ldpMp2mp           (7),
             transportTunnel    (8)
           }

    L2L3VpnMcastProviderTunnelId ::= TEXTUAL-CONVENTION
      STATUS       current
      DESCRIPTION
          "This textual convention represents the tunnel identifier Tunnel Identifier
           of a P-tunnel.

           The size of the identifier depends on the address family
           (IPv4 or IPv6) and the value of the corresponding
           L2L3VpnMcastProviderTunnelType object.

           The corresponding L2L3VpnMcastProviderTunnelType object
           represents the type of the tunneling technology used
           to establish the P-tunnel.

           The size of the identifier for each tunneling technology
           is summarized below.

            L2L3VpnMcastProviderTunnelType            Size (in octets)
             (tunneling technology)                      IPv4  IPv6
           -----------------------------------------------------------
             noTunnelInfo       (No tunnel information)    0     0
             rsvpP2mp           (RSVP-TE P2MP LSP)        12    24
             ldpP2mp            (mLDP P2MP LSP)           17    29
             pimSsm             (PIM-SSM Tree)             8    32
             pimAsm             (PIM-SM Tree)              8    32
             pimBidir           (BIDIR-PIM Tree)           8    32
             ingressReplication (Ingress Replication)      4    16
             ldpMp2mp           (mLDP MP2MP LSP)          17    29
             transportTunnel    (Transport Tunnel)         8    32

           The Tunnel type Type is set to 'No tunnel information present' information'
           when the PMSI Tunnel attribute carries no tunnel
           information (there is no Tunnel Identifier).
           The value of the corresponding L2L3VpnMcastProviderTunnelId
           object will be a string of length zero.

           For tunnel type Tunnel Type rsvpP2mp(1), the corresponding Tunnel
           Identifier is composed of an Extended Tunnel ID (4 octets in
           IPv4, 16 octets in IPv6), Reserved (2 octets), 2 unused (Reserved) octets that of
           value zero, a Tunnel ID (2 octets), and P2MP a Point-to-Multipoint
           (P2MP) ID (4 octets).  The size of the corresponding
           L2L3VpnMcastProviderTunnelId object will be 12 octets in IPv4
           and 24 octets in IPv6.

           For tunnel type Tunnel Type ldpP2mp(2), the corresponding Tunnel
           Identifier is the P2MP Forwarding Equivalence Class (FEC)
           Element
         [RFC6388]. (RFC 6388). The size of the corresponding
           L2L3VpnMcastProviderTunnelId object will be 17 octets
           in IPv4 and 29 octets in IPv6.

           For tunnel type Tunnel Types pimSsm(3), PimAsm(4), and PimBidir(5), the
           corresponding Tunnel Identifier is composed of the source IP
           address and the group IP address.
           The size of the corresponding L2L3VpnMcastProviderTunnelId
           object will be 8 octets in IPv4 and 32 octets in IPv6.

           For tunnel type Tunnel Type ingressReplication(6), the Tunnel Identifier
           is the unicast tunnel endpoint IP address of the local PE.
           The size of the corresponding L2L3VpnMcastProviderTunnelId
           object will be 4 octets in IPv4 and 16 octets in IPv6.

           For tunnel type Tunnel Type ldpMp2mp(7), the Tunnel Identifier is
         MP2MP
           a Multipoint-to-Multipoint (MP2MP) FEC Element [RFC6388]. (RFC 6388).
           The size of the corresponding L2L3VpnMcastProviderTunnelId
           object will be 17 octets in IPv4 and 29 octets in IPv6.

           For tunnel type Tunnel Type transportTunnel(8), the Tunnel Identifier
           is a tuple of Source PE Address and Local Number,
           which is a number that is unique to the Source PE [RFC7524]. (RFC 7524).
           Both Source PE Address and Local Number are 4 octets in IPv4
           and 16 octets in IPv6.
           The size of the corresponding L2L3VpnMcastProviderTunnelId
           object will be 8 octets in IPv4 and 32 octets in IPv6.
          "
      REFERENCE
        "RFC6514,
          "RFC 6514, Section 5
         RFC4875,
           RFC 4875, Section 19.1
         RFC6388, Section
           RFC 6388, Sections 2.2 and 3.2
         RFC7524,
           RFC 7524, Section 14.1
          "
      SYNTAX       OCTET STRING ( SIZE (0|4|8|12|16|17|24|29|32) )

    END

4.2.  L2L3-VPN-MULTICAST-MIB Object Definitions

   This MIB module makes reference to the following documents:
   [RFC3811].

  L2L3-VPN-MULTICAST-MIB DEFINITIONS ::= BEGIN

  IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, mib-2, zeroDotZero
       FROM SNMPv2-SMI                            -- [RFC2578] RFC 2578

    MODULE-COMPLIANCE, OBJECT-GROUP
       FROM SNMPv2-CONF                           -- [RFC2580] RFC 2580

    RowPointer
       FROM SNMPv2-TC                             -- [RFC2579] RFC 2579

    MplsLabel
       FROM MPLS-TC-STD-MIB                       -- [RFC3811] RFC 3811

    L2L3VpnMcastProviderTunnelType,
    L2L3VpnMcastProviderTunnelId
       FROM L2L3-VPN-MULTICAST-TC-MIB;            -- [RFCXXXX]

    -- RFC Ed.: replace XXXX with actual RFC number and remove this note 8502

  l2L3VpnMcastMIB MODULE-IDENTITY
    LAST-UPDATED "201809071200Z" "201812140000Z"  -- 7th September, 14 December 2018
    ORGANIZATION "IETF BESS Working Group." Group"
    CONTACT-INFO
          "        Zhaohui
                  "Zhaohui Zhang
                   Juniper Networks, Inc.
                   10 Technology Park Drive
                   Westford, MA 01886
                   USA
                   United States of America
                   Email: zzhang@juniper.net

                   Hiroshi Tsunoda
                   Tohoku Institute of Technology
                   35-1, Yagiyama Kasumi-cho
                   Taihaku-ku, Sendai, 982-8577
                   Japan
                   Email: tsuno@m.ieice.org

                  Comments and discussion to bess@ietf.org
                 "

    DESCRIPTION
        "This MIB module defines a table representing the attribute
         information of the provider tunnels (P-tunnels) on a PE router.
         This MIB module will be used by other MIB modules designed for
         monitoring and/or configuring Border Gateway
         Protocol/MultiProtocol
         Protocol/Multiprotocol Label Switching
         Layer 2 and Layer 3 Virtual Private
         Network that support multicast (L2L3VpnMCast network).

         Copyright (C) The Internet Society (2018). (c) 2018 IETF Trust and the persons identified
         as authors of the code.  All rights reserved.

         Redistribution and use in source and binary forms, with or
         without modification, is permitted pursuant to, and subject
         to the license terms contained in, the Simplified BSD License
         set forth in Section 4.c of the IETF Trust's Legal Provisions
         Relating to IETF Documents
         (http://trustee.ietf.org/license-info).
        "
    -- Revision history. History

    REVISION "201809071200Z" "201812140000Z"  -- 7th September, 14 December 2018
    DESCRIPTION
        "Initial version, published as RFC XXXX."

    -- RFC Ed.: replace XXXX with actual RFC number and remove this note 8502."

    ::= { mib-2 BBBB 245 }

  -- IANA Reg.: Please assign a value for "BBBB" under the
    -- 'mib-2' subtree and record the assignment in the SMI
    -- Numbers registry.

    -- RFC Ed.: When the above assignment has been made, please
    -- remove the above note
    -- replace "BBBB" here with the assigned value and
    -- remove this note.

  -- Top level Top-level components of this MIB.
  l2L3VpnMcastStates      OBJECT IDENTIFIER
                          ::= { l2L3VpnMcastMIB 1 }

  l2L3VpnMcastConformance OBJECT IDENTIFIER
                          ::= { l2L3VpnMcastMIB 2 }

  -- tables, scalars, conformance information Tables, Scalars, Conformance Information
  -- Table of PMSI Tunnel Attributes

  l2L3VpnMcastPmsiTunnelAttributeTable OBJECT-TYPE
     SYNTAX        SEQUENCE OF L2L3VpnMcastPmsiTunnelAttributeEntry
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
         "An entry in this table corresponds to
          the attribute information of a specific
          P-tunnel on a PE router.
          A part of the attributes correspond corresponds to fields in
          a Provider Multicast Service Interface (PMSI) Tunnel
          attribute advertised and received by a PE router.
          The entries will be referred to by other MIB modules
          for monitoring and/or configuring L2L3VpnMCast networks.
         "
     REFERENCE
         "RFC6514,
         "RFC 6514, Section 5"
     ::= { l2L3VpnMcastStates 1 }
  l2L3VpnMcastPmsiTunnelAttributeEntry OBJECT-TYPE
     SYNTAX        L2L3VpnMcastPmsiTunnelAttributeEntry
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
         "A conceptual row corresponding to a specific
          P-tunnel on this router.
         "
     REFERENCE
         "RFC6514,
         "RFC 6514, Section 5"
     INDEX {
             l2L3VpnMcastPmsiTunnelAttributeType,
             l2L3VpnMcastPmsiTunnelAttributeId
           }
     ::= { l2L3VpnMcastPmsiTunnelAttributeTable 1 }

  L2L3VpnMcastPmsiTunnelAttributeEntry ::=
      SEQUENCE {
          l2L3VpnMcastPmsiTunnelAttributeType
              L2L3VpnMcastProviderTunnelType,
          l2L3VpnMcastPmsiTunnelAttributeId
              L2L3VpnMcastProviderTunnelId,
          l2L3VpnMCastPmsiTunnelLeafInfoRequired
              INTEGER,
          l2L3VpnMcastPmsiTunnelAttributeMplsLabel
              MplsLabel,
          l2L3VpnMcastPmsiTunnelPointer
              RowPointer,
          l2L3VpnMcastPmsiTunnelIf
              RowPointer
      }

  l2L3VpnMcastPmsiTunnelAttributeType OBJECT-TYPE
     SYNTAX        L2L3VpnMcastProviderTunnelType
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
         "This object indicates the type of the tunneling technology
          used to establish the P-tunnel corresponding to this entry.

          When BGP-based PMSI signaling is used, the value of
          this object corresponds to the Tunnel Type field
          in the PMSI Tunnel attribute advertised/received
          in a PMSI auto-discovery (A-D) route.
         "
     REFERENCE
         "RFC6514,
         "RFC 6514, Section 5"
     ::= { l2L3VpnMcastPmsiTunnelAttributeEntry 1 }
  l2L3VpnMcastPmsiTunnelAttributeId OBJECT-TYPE
     SYNTAX        L2L3VpnMcastProviderTunnelId
     MAX-ACCESS    not-accessible
     STATUS        current
     DESCRIPTION
         "This object represents the Tunnel Identifier field, which
          uniquely identifies a P-tunnel, in the PMSI Tunnel attribute
          of the P-tunnel corresponding to this entry.

          The size of the identifier depends on the address family
          (IPv4 or IPv6) and the value of the corresponding
          l2L3VpnMcastPmsiTunnelAttributeType object object, i.e., the type of
          the
          tunneling technology used to establish the P-tunnel.
         "
     REFERENCE
         "RFC6514,
         "RFC 6514, Section 5"
     ::= { l2L3VpnMcastPmsiTunnelAttributeEntry 2 }

  l2L3VpnMCastPmsiTunnelLeafInfoRequired OBJECT-TYPE
     SYNTAX        INTEGER {
                       false        (0),
                       true         (1),
                       notAvailable (2)
                   }
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
         "When the value of this object is set to 1 (true),
          it indicates that the PE which that originated the
          PMSI Tunnel attribute of the P-tunnel corresponding
          to this entry requests receivers to originate
          a new Leaf A-D (Auto-Discovery) route.

          A value of 0 zero (false) indicates that there is no such
          request.

          When the P-tunnel does not have a corresponding PMSI
          tunnel
          Tunnel attribute, the value of this object will be
          2 (notAvailable).

          In the case of Multicast multicast in MPLS/BGP IP VPNs,
          this object represents the 'Leaf Information Required flag'
          [RFC6514]
          (RFC 6514) in the Flags field in the PMSI Tunnel attribute
          of the P-tunnel corresponding to this entry.
         "
     REFERENCE
         "RFC6514,
         "RFC 6514, Section 5
         "
     ::= { l2L3VpnMcastPmsiTunnelAttributeEntry 3 }

  l2L3VpnMcastPmsiTunnelAttributeMplsLabel OBJECT-TYPE
     SYNTAX        MplsLabel
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
         "This object represents the MPLS Label in the PMSI Tunnel
          attribute of the P-tunnel corresponding to this entry.

          When BGP-based PMSI signaling is used, the PMSI Tunnel
          attribute of the P-tunnel will be advertised/received
          in a PMSI auto-discovery (A-D) A-D route.  The value of
          this object corresponds to the MPLS Label in the attribute.

          When the P-tunnel does not have a PMSI tunnel
          attribute, the value of this object will be 0. zero.
         "
     REFERENCE
         "RFC6514,
         "RFC 6514, Section 5"
     ::= { l2L3VpnMcastPmsiTunnelAttributeEntry 4 }

  l2L3VpnMcastPmsiTunnelPointer OBJECT-TYPE
     SYNTAX        RowPointer
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
         "Details of a P-tunnel identified by
          l2L3VpnMcastPmsiTunnelAttributeId may be present
          in some other table, e.g.,
          mplsTunnelTable [RFC3812]. (RFC 3812).  This object specifies
          the pointer to the row that pertains to the entry
          in the table.

          If no such entry exists, the value of this object
          will be zeroDotZero.
         "
     REFERENCE
         "RFC3812, Section
         "RFC 3812, Sections 6.1 and Section 11"
     DEFVAL        { zeroDotZero }

     ::= { l2L3VpnMcastPmsiTunnelAttributeEntry 5 }

  l2L3VpnMcastPmsiTunnelIf OBJECT-TYPE
     SYNTAX        RowPointer
     MAX-ACCESS    read-only
     STATUS        current
     DESCRIPTION
         "If the P-tunnel identified by
          l2L3VpnMcastPmsiTunnelAttributeId has a corresponding
          entry in ifXTable [RFC2863], (RFC 2863), this object will
          point to the row in ifXTable that pertains to the entry.
          Otherwise, the value of this object will be zeroDotZero.
         "
     REFERENCE
         "RFC2863,
         "RFC 2863, Section 6"
     DEFVAL        { zeroDotZero }
     ::= { l2L3VpnMcastPmsiTunnelAttributeEntry 6 }

  -- Conformance Information

  l2L3VpnMcastCompliances OBJECT IDENTIFIER
                          ::= { l2L3VpnMcastConformance 1 }
  l2L3VpnMcastGroups      OBJECT IDENTIFIER
                          ::= { l2L3VpnMcastConformance 2 }

  -- Compliance Statements

  l2L3VpnMcastCoreCompliance MODULE-COMPLIANCE
      STATUS  current
      DESCRIPTION
         "The core compliance statement for SNMP entities
          which
          that implement the L2L3-VPN-MULTICAST-MIB Module." module.
         "
      MODULE  -- this module

      MANDATORY-GROUPS {
           l2L3VpnMcastCoreGroup
      }
      ::= { l2L3VpnMcastCompliances 1 }

  l2L3VpnMcastFullCompliance MODULE-COMPLIANCE
      STATUS  current
      DESCRIPTION
         "The full compliance statement for SNMP entities
          which
          that implement the L2L3-VPN-MULTICAST-MIB Module." module.
         "
      MODULE  -- this module

      MANDATORY-GROUPS {
           l2L3VpnMcastCoreGroup,
           l2L3VpnMcastOptionalGroup
      }
      ::= { l2L3VpnMcastCompliances 2 }

  -- units Units of conformance Conformance

  l2L3VpnMcastCoreGroup    OBJECT-GROUP
      OBJECTS {
          l2L3VpnMCastPmsiTunnelLeafInfoRequired,
          l2L3VpnMcastPmsiTunnelAttributeMplsLabel
      }
      STATUS      current
      DESCRIPTION
          "Support of these objects is required." required.
          "
      ::= { l2L3VpnMcastGroups 1 }

  l2L3VpnMcastOptionalGroup    OBJECT-GROUP
      OBJECTS {
          l2L3VpnMcastPmsiTunnelPointer,
          l2L3VpnMcastPmsiTunnelIf
      }
      STATUS      current
      DESCRIPTION
          "Support of these objects is optional." optional.
          "
      ::= { l2L3VpnMcastGroups 2 }

  END

5.  Security Considerations

   There are no management objects defined in these MIB modules that
   have a MAX-ACCESS clause of read-write and/or read-create.  So, if
   this MIB module is implemented correctly, then there is no risk that
   an intruder can alter or create any management objects of this MIB
   module via direct SNMP SET operations.

   Some of the readable objects in these MIB modules (i.e., objects with
   a MAX-ACCESS other than not-accessible) may be considered sensitive
   or vulnerable in some network environments.  This includes INDEX
   objects with a MAX-ACCESS of not-accessible, and any indices from
   other modules exposed via AUGMENTS.  It is thus important to control
   even GET and/or NOTIFY access to these objects and possibly to even
   encrypt the values of these objects when sending them over the
   network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  the l2L3VpnMcastPmsiTunnelAttributeTable collectively shows the
      P-tunnel network topology and its performance characteristics.

      For instance, l2L3VpnMcastPmsiTunnelAttributeId in this table will
      contain the identifier that uniquely identifies a P-tunnel.  This
      identifier may be composed of source and multicast group IP
      addresses.  l2L3VpnMcastPmsiTunnelPointer and
      l2L3VpnMcastPmsiTunnelIf will point to the corresponding entries
      in other tables containing configuration and/or performance
      information of a P-tunnel and its interface.  If an Administrator
      does not want to reveal this information, then these objects
      should be considered sensitive/vulnerable.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPsec),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB module.

   Implementations SHOULD provide the security features described by the
   SNMPv3 framework (see [RFC3410]), and implementations claiming
   compliance to the SNMPv3 standard MUST include full support for
   authentication and privacy via the User-based Security Model (USM)
   [RFC3414] with the AES cipher algorithm [RFC3826].  Implementations
   MAY also provide support for the Transport Security Model (TSM)
   [RFC5591] in combination with a secure transport such as SSH
   [RFC5592] or TLS/DTLS [RFC6353].

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

6.  IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER values recorded in the SMI Numbers "SMI Network Management MGMT
   Codes Internet-standard MIB" registry:

  Name                Description                OBJECT IDENTIFIER                OBJECT-IDENTIFIER value
  -----------------  --------------------------  ----------------------
  l2L3VpnMcastTCMIB   L2L3-VPN-MULTICAST-TC-MIB  { mib-2 AAAA 244 }
  l2L3VpnMcastMIB     L2L3-VPN-MULTICAST-MIB     { mib-2 BBBB 245 }

   Editor's Note (to be removed prior to publication): the IANA is
   requested to assign a value for "AAAA" and "BBBB" under the 'mib-2'
   subtree and to record the assignment in the SMI Numbers registry.
   When the assignment has been made, the RFC Editor is asked to replace
   "AAAA" and "BBBB" (here and in the MIB module) with the assigned
   value and to remove this note.

8.

7.  References

8.1.

7.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/
              RFC2119, 10.17487/RFC2119, March 1997, <https://www.rfc-editor.org/info/
              rfc2119>.
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC2578]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Structure of Management Information
              Version 2 (SMIv2)", STD 58, RFC 2578,
              DOI 10.17487/
              RFC2578, 10.17487/RFC2578, April 1999, <https://www.rfc-editor.org/info/
              rfc2578>.
              <https://www.rfc-editor.org/info/rfc2578>.

   [RFC2579]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Textual Conventions for SMIv2",
              STD 58, RFC 2579, DOI 10.17487/RFC2579, April 1999,
              <https://www.rfc-editor.org/info/rfc2579>.

   [RFC2580]  McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Conformance Statements for SMIv2",
              STD 58, RFC 2580, DOI 10.17487/RFC2580, April 1999,
              <https://www.rfc-editor.org/info/rfc2580>.

   [RFC2863]  McCloghrie, K. and F. Kastenholz, "The Interfaces Group
              MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000,
              <https://www.rfc-editor.org/info/rfc2863>.

   [RFC3414]  Blumenthal, U. and B. Wijnen, "User-based Security Model
              (USM) for version 3 of the Simple Network Management
              Protocol (SNMPv3)", STD 62, RFC 3414,
              DOI 10.17487/
              RFC3414, 10.17487/RFC3414, December 2002, <https://www.rfc-editor.org/info/
              rfc3414>.
              <https://www.rfc-editor.org/info/rfc3414>.

   [RFC3811]  Nadeau, T., Ed. and J. Cucchiara, Ed., "Definitions of
              Textual Conventions (TCs) for Multiprotocol Label
              Switching (MPLS) Management", RFC 3811,
              DOI 10.17487/
              RFC3811, 10.17487/RFC3811, June 2004, <https://www.rfc-editor.org/info/
              rfc3811>.
              <https://www.rfc-editor.org/info/rfc3811>.

   [RFC3812]  Srinivasan, C., Viswanathan, A., and T. Nadeau,
              "Multiprotocol Label Switching (MPLS) Traffic Engineering
              (TE) Management Information Base (MIB)", RFC 3812,
              DOI 10.17487/RFC3812, June 2004, <https://www.rfc-
              editor.org/info/rfc3812>.
              <https://www.rfc-editor.org/info/rfc3812>.

   [RFC3826]  Blumenthal, U., Maino, F., and K. McCloghrie, "The
              Advanced Encryption Standard (AES) Cipher Algorithm in the
              SNMP User-based Security Model", RFC 3826,
              DOI 10.17487/
              RFC3826, 10.17487/RFC3826, June 2004, <https://www.rfc-editor.org/info/
              rfc3826>.
              <https://www.rfc-editor.org/info/rfc3826>.

   [RFC4875]  Aggarwal, R., Ed., Papadimitriou, D., Ed., and S.
              Yasukawa, Ed., "Extensions to Resource Reservation
              Protocol - Traffic Engineering (RSVP-TE) for Point-to-
              Multipoint TE Label Switched Paths (LSPs)", RFC 4875,
              DOI 10.17487/RFC4875, May 2007, <https://www.rfc-
              editor.org/info/rfc4875>.
              <https://www.rfc-editor.org/info/rfc4875>.

   [RFC5015]  Handley, M., Kouvelas, I., Speakman, T., and L. Vicisano,
              "Bidirectional Protocol Independent Multicast (BIDIR-
              PIM)", RFC 5015, DOI 10.17487/RFC5015, October 2007,
              <https://www.rfc-editor.org/info/rfc5015>.

   [RFC5591]  Harrington, D. and W. Hardaker, "Transport Security Model
              for the Simple Network Management Protocol (SNMP)",
              STD 78, RFC 5591, DOI 10.17487/RFC5591, June 2009,
              <https://www.rfc-editor.org/info/rfc5591>.

   [RFC5592]  Harrington, D., Salowey, J., and W. Hardaker, "Secure
              Shell Transport Model for the Simple Network Management
              Protocol (SNMP)", RFC 5592, DOI 10.17487/RFC5592, June
              2009, <https://www.rfc-editor.org/info/rfc5592>.

   [RFC6353]  Hardaker, W., "Transport Layer Security (TLS) Transport
              Model for the Simple Network Management Protocol (SNMP)",
              STD 78, RFC 6353, DOI 10.17487/RFC6353, July 2011,
              <https://www.rfc-editor.org/info/rfc6353>.

   [RFC6388]  Wijnands, IJ., Ed., Minei, I., Ed., Kompella, K., and B.
              Thomas, "Label Distribution Protocol Extensions for Point-
              to-Multipoint and Multipoint-to-Multipoint Label Switched
              Paths", RFC 6388, DOI 10.17487/RFC6388, November 2011,
              <https://www.rfc-editor.org/info/rfc6388>.

   [RFC6513]  Rosen, E., Ed. and R. Aggarwal, Ed., "Multicast in MPLS/
              BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513, February
              2012, <https://www.rfc-editor.org/info/rfc6513>.

   [RFC6514]  Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
              Encodings and Procedures for Multicast in MPLS/BGP IP
              VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
              <https://www.rfc-editor.org/info/rfc6514>.

   [RFC7117]  Aggarwal, R., Ed., Kamite, Y., Fang, L., Rekhter, Y., and
              C. Kodeboniya, "Multicast in Virtual Private LAN Service
              (VPLS)", RFC 7117, DOI 10.17487/RFC7117, February 2014,
              <https://www.rfc-editor.org/info/rfc7117>.

   [RFC7524]  Rekhter, Y., Rosen, E., Aggarwal, R., Morin, T.,
              Grosclaude, I., Leymann, N., and S. Saad, "Inter-Area
              Point-to-Multipoint (P2MP) Segmented Label Switched Paths
              (LSPs)", RFC 7524, DOI 10.17487/RFC7524, May 2015,
              <https://www.rfc-editor.org/info/rfc7524>.

   [RFC7761]  Fenner, B., Handley, M., Holbrook, H., Kouvelas, I.,
              Parekh, R., Zhang, Z., and L. Zheng, "Protocol Independent
              Multicast - Sparse Mode (PIM-SM): Protocol Specification
              (Revised)", STD 83, RFC 7761, DOI 10.17487/RFC7761, March
              2016, <https://www.rfc-editor.org/info/rfc7761>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

8.2.

7.2.  Informative References

   [RFC3410]  Case, J., Mundy, R., Partain, D., and B. Stewart,
              "Introduction and Applicability Statements for Internet-
              Standard Management Framework", RFC 3410,
              DOI 10.17487/
              RFC3410, 10.17487/RFC3410, December 2002, <https://www.rfc-editor.org/info/
              rfc3410>.

7.  Acknowledgement
              <https://www.rfc-editor.org/info/rfc3410>.

Acknowledgements

   Glenn Mansfield Keeni did the MIB Doctor review and provided valuable
   comments.

Authors' Addresses

   Zhaohui (Jeffrey) Zhang
   Juniper Networks, Inc.
   10 Technology Park Drive
   Westford, MA  01886
   USA
   United States of America

   Email: zzhang@juniper.net
   Hiroshi Tsunoda
   Tohoku Institute of Technology
   35-1, Yagiyama Kasumi-cho
   Taihaku-ku, Sendai  982-8577
   Japan

   Phone: +81-22-305-3411
   Email: tsuno@m.ieice.org