Internet Engineering Task Force (IETF)                           F. Gont
Request for Comments: 9096                                  SI6 Networks
BCP: 234                                                         J. Zorz
Updates: 7084                                                   6connect
Category: Best Current Practice                             R. Patterson
ISSN: 2070-1721                                                   Sky UK
                                                                 B. Volz
                                                                   Cisco
                                                               July
                                                  Individual Contributor
                                                             August 2021

  Improving the Reaction of Customer Edge Routers to IPv6 Renumbering
                                 Events

Abstract

   This document specifies improvements to Customer Edge Routers routers that
   help mitigate the problems that may arise when network configuration
   information becomes invalid, invalid without any explicit signaling of that
   condition to the local nodes.  This document updates RFC 7084.

Status of This Memo

   This memo documents an Internet Best Current Practice.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   BCPs is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9096.

Copyright Notice

   Copyright (c) 2021 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction
   2.  Requirements Language
   3.  Improved Customer Edge Router Behavior
     3.1.  Automatic DHCPv6 RELEASEs
     3.2.  Stability of IAIDs
     3.3.  Interface between the WAN Side and LAN Side
     3.4.  LAN-Side Option Lifetimes
     3.5.  Signaling Stale Configuration Information
   4.  Recommended Option Lifetimes Configuration Values
   5.  IANA Considerations
   6.  Security Considerations
   7.  References
     7.1.  Normative References
     7.2.  Informative References
   Acknowledgments
   Authors' Addresses

1.  Introduction

   In scenarios where network configuration information becomes invalid
   without any explicit signaling of that condition (such as when a
   Customer Edge (CE) Router router crashes and reboots without knowledge of
   the previously employed configuration information), hosts on the
   local network will continue using stale information for an
   unacceptably long period of time, thus resulting in connectivity
   problems.  This problem is documented in detail in [RFC8978].

   This document specifies improvements to CE Routers routers that help mitigate
   the aforementioned problem for residential and small office
   scenarios.  It specifies recommendations for the default behavior of
   CE Routers and routers but does not preclude the availability of configuration
   knobs that might allow an operator or user to manually configure the
   CE Router router to deviate from these recommendations.  This document
   updates RFC 7084.

2.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

3.  Improved Customer Edge Router Behavior

   This section specifies and clarifies requirements for Customer Edge
   Routers CE routers that
   can help mitigate the problem discussed in Section 1, particularly
   when they employ prefixes learned via DHCPv6 Prefix Delegation
   (DHCPv6-PD) [RFC8415] on the WAN side with Stateless Address
   Autoconfiguration (SLAAC) [RFC4862] or DHCPv6 [RFC8415] on the LAN
   side.  The recommendations in this document help improve robustness
   at the Customer Edge Router CE router (on which the user or ISP may have no control) and
   do not preclude implementation of host-side improvements such as
   those specified in [6MAN-SLAAC-RENUM].

   This document specifies additional WAN-side prefix-delegation (WPD)
   requirements to those specified in [RFC7084]:

   WPD-9:  CE Routers routers SHOULD NOT automatically send DHCPv6-PD RELEASE
      messages upon reboot restart events.  See Section 3.1 for further
      details.

   WPD-10:  CE Routers routers MUST by default use a WAN-side Identity
      Association IDentifier (IAID) value that is stable between CE
      Router
      router restarts, DHCPv6 client restarts, or interface state
      changes (e.g., Transient transient PPP interfaces), unless the CE Router router
      employs the IAID techniques discussed in Section 4.5 of [RFC7844].
      See Section 3.2 for further details.

   This document also replaces LAN-side requirement L-13 from [RFC7084]
   with:

   L-13:  CE routers MUST signal stale configuration information as
      specified in Section 3.5.

   Finally, this document specifies the following additional LAN-side
   requirements to those from [RFC7084]:

   L-15:  CE routers MUST NOT advertise prefixes via SLAAC or assign
      addresses or delegate prefixes via DHCPv6 on the LAN side,
      employing side using
      lifetimes that exceed the remaining lifetimes of the corresponding
      prefixes learned from on the WAN side via DHCPv6-PD.  For more details,
      see Section 3.3.

   L-16:  CE routers SHOULD advertise capped SLAAC option lifetimes and lifetimes,
      capped DHCPv6 IA Address Option option lifetimes, and capped IA Prefix Option
      option lifetimes, as specified in Section 3.4.

3.1.  Automatic DHCPv6 RELEASEs

   Some CE Routers routers are known to automatically send DHCPv6-PD RELEASE
   messages upon reboot restart events.  However, this may inadvertently
   trigger a flash-renumbering scenario, along with the associated
   problems discussed in [RFC8978], that this document attempts to
   mitigate.

   As a result, requirement WPD-9 from Section 3 specifies that CE
   routers SHOULD NOT automatically send DHCPv6-PD RELEASE messages upon
   reboot
   restart events.

3.2.  Stability of IAIDs

   [RFC8415] requires that the IAID for an IA MUST be consistent across
   restarts of the DHCP client.  However, some popular CE Routers routers are
   known to select new random IAIDs, e.g., every time the underlying PPP
   session is established. established or when the device is rebooted.  This could be
   the result of extrapolating the behavior described in [RFC7844] or
   simply a consequence of not storing IAIDs on stable storage along
   with failing failure to employ an algorithm that consistently generates the
   same IAID upon reboots.  Thus, requirement WPD-10 from Section 3
   prevents CE Routers routers from inadvertently triggering flash-renumbering
   events on the local network.

3.3.  Interface between the WAN Side and LAN Side

   The "Preferred Lifetime" and "Valid Lifetime" of Prefix Information
   Options (PIOs) [RFC4861] corresponding to prefixes learned via
   DHCPv6-PD on the WAN side MUST NOT span past the remaining preferred
   and valid lifetimes of the corresponding DHCPv6-PD prefixes.  This
   means that the "Preferred Lifetime" and the "Valid Lifetime"
   advertised in PIOs by the CE router MUST be dynamically adjusted such
   that they never span past the remaining preferred and valid lifetimes
   of the corresponding prefixes delegated via DHCPv6-PD on the WAN
   side.

   Similarly, the "preferred-lifetime" and "valid-lifetime" of DHCPv6 IA
   Address Options options and DHCPv6 IA Prefix Options options employed with DHCPv6 on
   the LAN side MUST NOT span past the remaining preferred and valid
   lifetimes of the corresponding prefixes leased learned via DHCPv6-PD on the
   WAN side.  This means that the "preferred-lifetime" and "valid-
   lifetime" of DHCPv6 IA Address Options options and DHCPv6 IA Prefix Options options
   employed with DHCPv6 on the LAN side MUST be dynamically adjusted
   such that they never span past the remaining preferred and valid
   lifetimes of the corresponding prefixes delegated to the CE router on
   the WAN side via DHCPv6-PD.

   RATIONALE:

   *  The lifetime values employed for the "Preferred Lifetime"
      (AdvPreferredLifetime) and "Valid Lifetime" (AdvValidLifetime) of
      SLAAC Prefix Information Options must never be larger than the
      remaining lifetimes for of the corresponding prefix prefixes (as learned via
      DHCPv6-PD on the WAN side).  This is in line with the requirement
      from Section 6.3 of [RFC8415], which states:

   |  In particular, if the delegated prefix or a prefix derived from it
   |  is advertised for stateless address autoconfiguration [RFC4862],
   |  the advertised preferred and valid lifetimes MUST NOT exceed the
   |  corresponding remaining lifetimes of the delegated prefix.

   *  The lifetime values of prefixes advertised on the LAN side via
      SLAAC must be dynamically updated (rather than static values);
      otherwise, the advertised lifetimes would eventually span past the
      DHCPv6-PD lifetimes.

   *  The same considerations apply for the valid-lifetime "valid-lifetime" and
      preferred-lifetime
      "preferred-lifetime" of IA Address Options options and IA Prefix Options options
      employed with DHCPv6 on the LAN side.

3.4.  LAN-Side Option Lifetimes

   CE Routers routers SHOULD override the default lifetime values of Neighbor
   Discovery options that depend in any way on changes in the prefix
   employed for address configuration on the LAN side, and employ
   shorter lifetime values to improve the robustness to renumbering
   events, while complying with the requirements from Section 3.3 of
   this document and the recommendations in [RFC7772].

   CE Routers routers SHOULD set the "Router Lifetime" of Router Lifetime Advertisement
   (RA) messages to ND_PREFERRED_LIMIT.

   CE Routers routers SHOULD also set the PIO Preferred Lifetime "Preferred Lifetime" to the lesser
   of the remaining preferred lifetime of the corresponding prefix (see
   Section 3.3) and ND_PREFERRED_LIMIT, and set the PIO Valid Lifetime "Valid Lifetime"
   to the lesser of the remaining valid lifetime of the corresponding
   prefix and ND_VALID_LIMIT.  Additionally, the
   Route Lifetime "Route Lifetime" of
   Route Information Options (RIOs) [RFC4191], the
   Lifetime "Lifetime" of
   Recursive DNS Search Options (RDNSSOs) Server (RDNSS) options [RFC8106], and the
   Lifetime "Lifetime" of
   DNS Search List Options (DNSSLOs) (DNSSL) options [RFC8106] SHOULD be set to the lesser
   of the longest valid-lifetime in remaining valid lifetime of a DHCPv6 IA Prefix
   Option (received prefix (leased via
   DHCPv6 on the WAN side) and ND_VALID_LIMIT, if any of these options
   are included in Router Advertisement (RA) messages.

      NOTE: In scenarios where the valid-lifetime valid lifetime and the preferred- preferred
      lifetime of the prefix leased prefixes learned via DHCPv6 on the WAN side are always
      larger than ND_VALID_LIMIT and ND_PREFERRED_LIMIT, respectively,
      the lifetime values advertised on the LAN side will not experience
      actual changes.

   The above text refers to the Neighbor Discovery options that are
   typically employed by CE Routers. routers.  A CE Router router may need to apply the
   same policy for setting the lifetime of other Neighbor Discovery
   options it employs, if and where applicable.

   CE Routers routers providing stateful address configuration via DHCPv6 SHOULD
   set the "preferred-lifetime" of a DHCPv6 IA Address Option preferred-lifetime option to the
   lesser of the remaining preferred lifetime of the corresponding
   prefix (see Section 3.3) and ND_PREFERRED_LIMIT, and set the valid-lifetime "valid-
   lifetime" of the same option to the lesser of the remaining valid
   lifetime of the corresponding prefix and ND_VALID_LIMIT.

   CE Routers routers providing DHCPv6-PD on the LAN side SHOULD set the
   "preferred-lifetime" of a DHCPv6 IA Prefix Option preferred-lifetime option to the lesser of
   the remaining preferred lifetime of the corresponding prefix (see
   Section 3.3) and ND_PREFERRED_LIMIT, and set the valid-lifetime "valid-lifetime" of
   the same option to the lesser of the remaining valid lifetime of the
   corresponding prefix and ND_VALID_LIMIT.

   RATIONALE:

   *  The Valid Lifetime "Valid Lifetime" and Preferred Lifetime "Preferred Lifetime" of PIOs have a
      direct impact on three different aspects:

      -  The amount of time hosts may end up employing stale network
         configuration information (see [RFC8978]).

      -  The amount of time CE Routers routers need to persist trying to
         deprecate stale network configuration information (e.g., to
         handle cases where hosts miss Router Advertisements Advertisement messages and
         thus still consider the stale information as valid).

      -  The amount of information that CE Routers routers need to maintain
         when, e.g., multiple crash-and-reboot events occur in the time
         span represented by the option lifetimes employed on the LAN
         side.

   *  CE Routers routers need not employ the (possibly long) WAN-side DHCPv6-PD
      lifetimes for the Valid Lifetime "Valid Lifetime" and Preferred Lifetime "Preferred Lifetime" of
      PIOs sent in Router Advertisement messages to advertise sub-prefixes sub-
      prefixes of the leased prefix.  Instead, CE Routers routers SHOULD use
      shorter values for the Valid Lifetime "Valid Lifetime" and Preferred Lifetime "Preferred Lifetime"
      of PIOs, since subsequent Router Advertisement messages will
      nevertheless refresh the associated lifetimes, leading to the same
      effective lifetimes as specified by the WAN-side DHCPv6-PD
      lifetimes.

   *  Similarly, CE Routers routers need not employ the (possibly long) WAN-side
      DHCPv6-PD lifetimes for the valid-lifetime "valid-lifetime" and preferred-lifetime "preferred-
      lifetime" of IA Address Options options and IA Prefix Options options employed by
      DHCPv6 on the LAN side, since the renewal of bindings by DHCPv6
      clients will lead to the same effective lifetimes as specified by
      the WAN-side DHCPv6-PD lifetimes.

3.5.  Signaling Stale Configuration Information

   When a CE Router router provides LAN-side address-configuration information
   via SLAAC:

   *  A CE Router router sending RAs that advertise prefixes belonging to a
      dynamically learned
      prefixes prefix (e.g., via DHCPv6-PD) SHOULD record, on
      stable storage, the list of prefixes being advertised via PIOs on
      each network segment and the state of the "A" and "L" flags of the
      corresponding PIOs.

   *  Upon changes to the advertised prefixes, and after bootstrapping,
      the CE Router router advertising prefix information via SLAAC proceeds as
      follows:

      -  Any prefixes that were previously advertised by the CE Router router
         via PIOs in RA messages, but that have now become stale, MUST
         be advertised with a PIO PIOs that has have the "Valid Lifetime" and the
         "Preferred Lifetime" set to 0 and the "A" and "L" bits
         unchanged.

      -  The aforementioned advertisement advertisements MUST be performed for at
         least the "Valid Lifetime" previously employed for such prefix.
         prefixes.  The CE Router router MUST advertise this information with
         unsolicited Router Advertisements Advertisement messages, as described in
         Section 6.2.4 of
         [RFC4861] [RFC4861], and MAY advertise this information
         via unicast Router
         Advertisements Advertisement messages when possible and
         applicable.

         o  Note:

            NOTE: If requirement L-16 (Section 3.4) 3) is followed, the
            Valid Lifetime
            "Valid Lifetime" need not be saved, and the stale prefix can
            simply be advertised for a period of ND_VALID_LIMIT.

   *  CE Routers routers receiving DHCPv6 IA Prefix Delegations options with a 0 valid-
      lifetime "valid-
      lifetime" MUST advertise the corresponding sub-prefixes (as they
      would be generated for the same leased prefix with a non-zero
      lifetime) with a PIO PIOs with both the Preferred Lifetime "Preferred Lifetime" and the
      Valid Lifetime
      "Valid Lifetime" set to 0, for at least the WAN-side DHCPv6-PD
      valid-lifetime,
      "valid-lifetime", or for a period of ND_VALID_LIMIT if the
      recommended lifetimes from Section 3.4 are employed.

   When a CE Router router provides LAN-side DHCPv6 (address assignment or
   prefix delegation), then:

   *  The CE Router router SHOULD record, on stable storage, the DHCPv6 address
      and delegated-prefix bindings corresponding to the LAN side.

   *  If the CE Router router finds that the prefix to be employed for address
      assignment and/or prefix delegation has changed (e.g., upon a
      crash-and-reboot event) or the CE Router router receives DHCPv6 IA Prefix
      Delegations
      options with 0 lifetimes, the CE Router router MUST:

      -  In Replies to DHCPv6 Request, Renew, and Rebind messages, send
         IA Address Options options or IA Prefix Options options (as appropriate) for
         any address assignments or prefix delegations for the
         deprecated stale
         prefixes.  The aforementioned options MUST be sent with both
         the valid-lifetime "valid-lifetime" and the preferred-lifetime "preferred-lifetime" set to 0, for
         at least the valid-lifetime "valid-lifetime" originally employed for them, or
         for a period of ND_VALID_LIMIT if the recommended lifetimes
         from Section 3.4 are employed.

      -  Initiate sending Reconfigure messages (if possible, i.e., messages, if possible (i.e.,
         client requests Reconfigure support and the CE Router router offers
         it)
         it), to those clients with address assignments or prefix
         delegations for the deprecated stale prefixes.

   RATIONALE:

      -

   *  IPv6 network renumbering is expected to take place in a planned
      manner with old/stale prefixes being phased out via reduced prefix
      lifetimes while new prefixes (with normal lifetimes) are
      introduced.  However, a number of scenarios may lead to the so-
      called "flash-renumbering" events, where the a prefix being employed
      on a network suddenly becomes invalid and replaced by a new prefix
      [RFC8978].  One such scenario is when a DHCPv6
         server an Internet Service Provider
      (ISP) employs dynamic prefixes and the Customer Edge Router CE router crashes and
      reboots.  The requirements in this section are meant to allow Customer Edge Routers CE
      routers to deprecate stale information in such scenarios.

      -

   *  The recommendations in this section expand from requirement L-13
      in Section 4.3 of [RFC7084] and Section 6.3 of [RFC8415].

      -  Host

   *  Hosts configuring addresses via SLAAC on the local network may
      employ addresses configured for the previously advertised prefixes
      for at most the "Valid Lifetime" of the corresponding
         PIO PIOs of the
      last received Router Advertisement message. messages.  Since Router
      Advertisement messages may be lost or fail to be received for
      various reasons, Customer Edge Routers CE routers need to try to deprecate stale
      prefixes for a period of time equal to the "Valid Lifetime" of the
      PIO employed when originally advertising the prefix.

      -

   *  The requirement requirements in this section is to store information on stable
      storage are conveyed as a "SHOULD" (as opposed to a "MUST"), since the requirement to store
         information on stable storage
      they may represent a challenge for some implementations.

      -

   *  Advertising DHCPv6-leased prefixes with zero lifetimes on the LAN
      side would handle the case where a CE Router router has no stable storage
      but receives the prefixes via DHCPv6 with 0 lifetimes.

      -

   *  The above text does not include DHCPv6 Advertise messages sent in
      response to DHCPv6 Solicit messages, since Section 18.3.9 of
      [RFC8415] requires that a DHCPv6 server that is not going to
      assign an address or delegated prefix received as a hint in the
      Solicit message MUST NOT include that address or delegated prefix
      in the Advertise message.  Additionally, any subsequent Request
      messages will trigger the response specified in this section and
      therefore cause the address or prefix to be deprecated.

4.  Recommended Option Lifetimes Configuration Values

   *  ND_PREFERRED_LIMIT: 2700 seconds (45 minutes)

   *  ND_VALID_LIMIT: 5400 seconds (90 minutes)

   RATIONALE:

   *  These values represent a trade-off among a number of factors,
      including responsiveness and possible impact on the battery life
      of connected devices [RFC7772].

   *  ND_PREFERRED_LIMIT is set according to the recommendations in
      [RFC7772] for Router Lifetime, the "Router Lifetime", following the rationale from
      Section 3.2 of [RFC8978].

   *  ND_VALID_LIMIT is set to 2 * ND_PREFERRED_LIMIT to provide some
      additional leeway before configuration information is finally
      discarded by the host. hosts.

5.  IANA Considerations

   This document has no IANA actions.

6.  Security Considerations

   This document discusses a problem that may arise arise, e.g., in scenarios
   where dynamic IPv6 prefixes are employed, and it proposes
   improvements to
   Customer Edge Routers CE routers [RFC7084] to mitigate the problem for
   residential or small office scenarios.  It does not introduce new
   security issues; thus, the same security considerations as for
   [RFC4861], [RFC4862], [RFC7084], and [RFC8415] apply.

7.  References

7.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC4191]  Draves, R. and D. Thaler, "Default Router Preferences and
              More-Specific Routes", RFC 4191, DOI 10.17487/RFC4191,
              November 2005, <https://www.rfc-editor.org/info/rfc4191>.

   [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              DOI 10.17487/RFC4861, September 2007,
              <https://www.rfc-editor.org/info/rfc4861>.

   [RFC4862]  Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862,
              DOI 10.17487/RFC4862, September 2007,
              <https://www.rfc-editor.org/info/rfc4862>.

   [RFC7772]  Yourtchenko, A. and L. Colitti, "Reducing Energy
              Consumption of Router Advertisements", BCP 202, RFC 7772,
              DOI 10.17487/RFC7772, February 2016,
              <https://www.rfc-editor.org/info/rfc7772>.

   [RFC7844]  Huitema, C., Mrugalski, T., and S. Krishnan, "Anonymity
              Profiles for DHCP Clients", RFC 7844,
              DOI 10.17487/RFC7844, May 2016,
              <https://www.rfc-editor.org/info/rfc7844>.

   [RFC8106]  Jeong, J., Park, S., Beloeil, L., and S. Madanapalli,
              "IPv6 Router Advertisement Options for DNS Configuration",
              RFC 8106, DOI 10.17487/RFC8106, March 2017,
              <https://www.rfc-editor.org/info/rfc8106>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8415]  Mrugalski, T., Siodelski, M., Volz, B., Yourtchenko, A.,
              Richardson, M., Jiang, S., Lemon, T., and T. Winters,
              "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)",
              RFC 8415, DOI 10.17487/RFC8415, November 2018,
              <https://www.rfc-editor.org/info/rfc8415>.

7.2.  Informative References

   [6MAN-SLAAC-RENUM]
              Gont, F., Zorz, J., and R. Patterson, "Improving the
              Robustness of Stateless Address Autoconfiguration (SLAAC)
              to Flash Renumbering Events", Work in Progress, Internet-
              Draft, draft-ietf-6man-slaac-renum-02, 19 January 2021,
              <https://datatracker.ietf.org/doc/html/draft-ietf-6man-
              slaac-renum-02>.

   [RFC7084]  Singh, H., Beebee, W., Donley, C., and B. Stark, "Basic
              Requirements for IPv6 Customer Edge Routers", RFC 7084,
              DOI 10.17487/RFC7084, November 2013,
              <https://www.rfc-editor.org/info/rfc7084>.

   [RFC8978]  Gont, F., Žorž, J., and R. Patterson, "Reaction of IPv6
              Stateless Address Autoconfiguration (SLAAC) to Flash-
              Renumbering Events", RFC 8978, DOI 10.17487/RFC8978, March
              2021, <https://www.rfc-editor.org/info/rfc8978>.

Acknowledgments

   The authors would like to thank Owen DeLong, Philip Homburg, Erik
   Kline, and Ted Lemon for their valuable help in improving this
   document via successive detailed reviews.

   The authors would like to thank Mikael Abrahamsson, Luis Balbinot,
   Brian Carpenter, Tim Chown, Lorenzo Colitti, Alejandro D'Egidio, Gert
   Doering, Fernando Frediani, Guillermo Gont, Steinar Haug, Nick
   Hilliard, Lee Howard, Christian Huitema, Sheng Jiang, Benjamin Kaduk,
   Suresh Krishnan, Warren Kumari, Albert Manfredi, Olorunloba Olopade,
   Jordi Palet Martinez, Richard Patterson, Pete Resnick, Michael Richardson, Mark Smith,
   Job Snijders, Sander Steffann, Tarko Tikan, Ole Troan, Loganaden
   Velvindron, Éric Vyncke, Robert Wilton, Timothy Winters, Christopher
   Wood, and Chongfeng Xie for providing valuable comments on earlier
   draft versions of this document.

   Fernando would also like to thank Brian Carpenter who, over the
   years, has answered many questions and provided valuable comments
   that have benefited his protocol-related work.

Authors' Addresses

   Fernando Gont
   SI6 Networks
   7mo Piso
   Segurola y Habana 4310
   Villa Devoto
   Ciudad Autonoma de Buenos Aires
   Argentina

   Email: fgont@si6networks.com
   URI:   https://www.si6networks.com

   Jan Zorz
   6connect

   Email: jan@6connect.com

   Richard Patterson
   Sky UK

   Email: richard.patterson@sky.uk

   Bernie Volz
   Cisco Systems, Inc.
   300 Beaver Brook Rd
   Boxborough, MA 01719
   Individual Contributor
   116 Hawkins Pond Road
   Center Harbor, NH 03226
   United States of America

   Email: volz@cisco.com bevolz@gmail.com