Internet Engineering Task Force (IETF)                          C. Hopps
Request for Comments: 9179                       LabN Consulting, L.L.C.
Category: Standards Track                                  December 2021                                  February 2022
ISSN: 2070-1721

                A YANG Grouping for Geographic Locations

Abstract

   This document defines a generic geographical location YANG grouping.
   The geographical location grouping is intended to be used in YANG
   data models for specifying a location on or in reference to Earth or
   any other astronomical object.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9179.

Copyright Notice

   Copyright (c) 2021 2022 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Revised BSD License text as described in Section 4.e of the
   Trust Legal Provisions and are provided without warranty as described
   in the Revised BSD License.

Table of Contents

   1.  Introduction
     1.1.  Terminology
   2.  The Geolocation Object
     2.1.  Frame of Reference
     2.2.  Location
     2.3.  Motion
     2.4.  Nested Locations
     2.5.  Non-location Attributes
     2.6.  Tree
   3.  YANG Module
   4.  ISO 6709:2008 Conformance
   5.  Usability
     5.1.  Portability
       5.1.1.  IETF URI Value
       5.1.2.  W3C
       5.1.3.  Geography Markup Language (GML)
       5.1.4.  KML
   6.  IANA Considerations
     6.1.  Geodetic System Values Registry
     6.2.  Updates to the IETF XML Registry
     6.3.  Updates to the YANG Module Names Registry
   7.  Security Considerations
   8.  Normative References
   9.  Informative References
   Appendix A.  Examples
   Acknowledgments
   Author's Address

1.  Introduction

   In many applications, we would like to specify the location of
   something geographically.  Some examples of locations in networking
   might be the location of data centers, a rack in an Internet exchange
   point, a router, a firewall, a port on some device, or it could be
   the endpoints of a fiber, or perhaps the failure point along a fiber.

   Additionally, while this location is typically relative to Earth, it
   does not need to be.  Indeed, it is easy to imagine a network or
   device located on the Moon, on Mars, on Enceladus (the moon of
   Saturn), or even on a comet (e.g., 67p/churyumov-gerasimenko).

   Finally, one can imagine defining locations using different frames of
   reference or even alternate systems (e.g., simulations or virtual
   realities).

   This document defines a geo-location 'geo-location' YANG grouping that allows for
   all the above data to be captured.

   This specification conforms to [ISO.6709.2008].

   The YANG data model described in this document conforms to the
   Network Management Datastore Architecture (NMDA) defined in
   [RFC8342].

1.1.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  The Geolocation Object

2.1.  Frame of Reference

   The frame of reference (reference-frame) ('reference-frame') defines what the location
   values refer to and their meaning.  The referred-to object can be any
   astronomical body.  It could be a planet such as Earth or Mars, a
   moon such as Enceladus, an asteroid such as Ceres, or even a comet
   such as 1P/Halley.  This value is specified in astronomical-body 'astronomical-body'
   and is defined by the International Astronomical Union
   <http://www.iau.org>.  The default astronomical-body 'astronomical-body' value is earth.
   'earth'.

   In addition to identifying the astronomical body, we also need to
   define the meaning of the coordinates (e.g., latitude and longitude)
   and the definition of 0-height.  This is done with a geodetic-datum 'geodetic-datum'
   value.  The default value for geodetic-datum 'geodetic-datum' is wgs-84 'wgs-84' (i.e., the
   World Geodetic System [WGS84]), which is used by the Global
   Positioning System (GPS) among many others.  We define an IANA
   registry for specifying standard values for the geodetic-datum. 'geodetic-datum'.

   In addition to the geodetic-datum 'geodetic-datum' value, we allow overriding the
   coordinate and height accuracy using coord-accuracy 'coord-accuracy' and height-
   accuracy, 'height-
   accuracy', respectively.  When specified, these values override the
   defaults implied by the geodetic-datum 'geodetic-datum' value.

   Finally, we define an optional feature that allows for changing the
   system for which the above values are defined.  This optional feature
   adds an alternate-system 'alternate-system' value to the reference frame.  This value
   is normally not present, which implies the natural universe is the
   system.  The use of this value is intended to allow for creating
   virtual realities or perhaps alternate coordinate systems.  The
   definition of alternate systems is outside the scope of this
   document.

2.2.  Location

   This is the location on, or relative to, the astronomical object.  It
   is specified using two or three coordinate values.  These values are
   given either as latitude, longitude, 'latitude', 'longitude', and an optional height, 'height', or
   as Cartesian coordinates of x, y, 'x', 'y', and z. 'z'.  For the standard
   location choice, latitude 'latitude' and longitude 'longitude' are specified as decimal
   degrees, and the height 'height' value is in fractions of meters.  For the
   Cartesian choice, x, y, 'x', 'y', and z 'z' are in fractions of meters.  In
   both choices, the exact meanings of all the values are defined by the geodetic-datum
   'geodetic-datum' value in Section 2.1.

2.3.  Motion

   Support is added for objects in relatively stable motion.  For
   objects in relatively stable motion, the grouping provides a three-
   dimensional vector value.  The components of the vector are v-north,
   v-east,
   'v-north', 'v-east', and v-up, 'v-up', which are all given in fractional
   meters per second.  The values v-north 'v-north' and v-east 'v-east' are relative to
   true north as defined by the reference frame for the astronomical
   body; v-up 'v-up' is perpendicular to the plane defined by v-north 'v-north' and v-east,
   'v-east', and is pointed away from the center of mass.

   To derive the two-dimensional heading and speed, one would use the
   following formulas:

                 ,------------------------------
       speed =  V  v_{north}^{2} + v_{east}^{2}

       heading = arctan(v_{east} / v_{north})

   For some applications that demand high accuracy and where the data is
   infrequently updated, this velocity vector can track very slow
   movement such as continental drift.

   Tracking more complex forms of motion is outside the scope of this
   work.  The intent of the grouping being defined here is to identify
   where something is located, and generally this is expected to be
   somewhere on, or relative to, Earth (or another astronomical body).
   At least two options are available to YANG data models that wish to
   use this grouping with objects that are changing location frequently
   in non-simple ways.  They  A data model can either add additional motion
   data to their its model directly.  Or, directly, or if the application allows, it can
   require more frequent queries to keep the location data current.

2.4.  Nested Locations

   When locations are nested (e.g., a building may have a location that
   houses routers that also have locations), the module using this
   grouping is free to indicate in its definition that the reference-
   frame 'reference-
   frame' is inherited from the containing object so that the reference-
   frame
   'reference-frame' need not be repeated in every instance of location
   data.

2.5.  Non-location Attributes

   During the development of this module, the question of whether it
   would support data such as orientation arose.  These types of
   attributes are outside the scope of this grouping because they do not
   deal with a location but rather describe something more about the
   object that is at the location.  Module authors are free to add these
   non-location attributes along with their use of this location
   grouping.

2.6.  Tree

   The following is the YANG tree diagram [RFC8340] for the geo-location
   grouping.

     module: ietf-geo-location
       grouping geo-location:
         +-- geo-location
            +-- reference-frame
            |  +-- alternate-system?    string {alternate-systems}?
            |  +-- astronomical-body?   string
            |  +-- geodetic-system
            |     +-- geodetic-datum?    string
            |     +-- coord-accuracy?    decimal64
            |     +-- height-accuracy?   decimal64
            +-- (location)?
            |  +--:(ellipsoid)
            |  |  +-- latitude?    decimal64
            |  |  +-- longitude?   decimal64
            |  |  +-- height?      decimal64
            |  +--:(cartesian)
            |     +-- x?           decimal64
            |     +-- y?           decimal64
            |     +-- z?           decimal64
            +-- velocity
            |  +-- v-north?   decimal64
            |  +-- v-east?    decimal64
            |  +-- v-up?      decimal64
            +-- timestamp?         yang:date-and-time
            +-- valid-until?       yang:date-and-time

3.  YANG Module

   This model imports Common YANG Data Types [RFC6991].  It uses YANG
   version 1.1 [RFC7950].

   <CODE BEGINS> file "ietf-geo-location@2021-12-15.yang" "ietf-geo-location@2022-2-7.yang"
   module ietf-geo-location {
     yang-version 1.1;
     namespace "urn:ietf:params:xml:ns:yang:ietf-geo-location";
     prefix geo;
     import ietf-yang-types {
       prefix yang;
       reference "RFC 6991: Common YANG Data Types";
     }

     organization
       "IETF NETMOD Working Group (NETMOD)";
     contact
      "WG Web:   <https://datatracker.ietf.org/wg/netmod/>
       WG List:  <mailto:netmod@ietf.org>

       Editor:   Christian Hopps
                 <mailto:chopps@chopps.org>";

     description
       "This module defines a grouping of a container object for
        specifying a location on or around an astronomical object (e.g.,
        'earth').

        The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
        NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
        'MAY', and 'OPTIONAL' in this document are to be interpreted as
        described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
        they appear in all capitals, as shown here.

        Copyright (c) 2021 2022 IETF Trust and the persons identified as
        authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject to
        the license terms contained in, the Revised BSD License set
        forth in Section 4.e of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (https://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC 9179
        (https://www.rfc-editor.org/info/rfc9179); see the RFC itself
        for full legal notices.";

     revision 2021-12-15 2022-2-7 {
       description
         "Initial Revision";
       reference
         "RFC 9179: A YANG Grouping for Geographic Locations";
     }

     feature alternate-systems {
       description
         "This feature means the device supports specifying locations
          using alternate systems for reference frames.";
     }

     grouping geo-location {
       description
         "Grouping to identify a location on an astronomical object.";

       container geo-location {
         description
           "A location on an astronomical body (e.g., 'earth')
            somewhere in a universe.";

         container reference-frame {
           description
             "The Frame of Reference for the location values.";

           leaf alternate-system {
             if-feature "alternate-systems";
             type string;
             description
               "The system in which the astronomical body and
                geodetic-datum is defined.  Normally, this value is not
                present and the system is the natural universe; however,
                when present, this value allows for specifying alternate
                systems (e.g., virtual realities).  An alternate-system
                modifies the definition (but not the type) of the other
                values in the reference frame.";
           }
           leaf astronomical-body {
             type string {
               pattern '[ -@\[-\^_-~]*';
             }
             default "earth";
             description
               "An astronomical body as named by the International
                Astronomical Union (IAU) or according to the alternate
                system if specified.  Examples include 'sun' (our star),
                'earth' (our planet), 'moon' (our moon), 'enceladus' (a
                moon of Saturn), 'ceres' (an asteroid), and
                '67p/churyumov-gerasimenko (a comet).  The ASCII value
                SHOULD have uppercase converted to lowercase and not
                include control characters (i.e., values 32..64, and
                91..126).  Any preceding 'the' in the name SHOULD NOT be
                included.";
             reference
               "https://www.iau.org/";
           }
           container geodetic-system {
             description
               "The geodetic system of the location data.";
             leaf geodetic-datum {
               type string {
                 pattern '[ -@\[-\^_-~]*';
               }
               description
                 "A geodetic-datum defining the meaning of latitude,
                  longitude, and height.  The default when the
                  astronomical body is 'earth' is 'wgs-84', which is
                  used by the Global Positioning System (GPS).  The
                  ASCII value SHOULD have uppercase converted to
                  lowercase and not include control characters
                  (i.e., values 32..64, and 91..126).  The IANA registry
                  further restricts the value by converting all spaces
                  (' ') to dashes ('-').
                  The specification for the geodetic-datum indicates
                  how accurately it models the astronomical body in
                  question, both for the 'horizontal'
                  latitude/longitude coordinates and for height
                  coordinates.";
               reference
                 "RFC 9179: A YANG Grouping for Geographic Locations,
                  Section 6.1";
             }
             leaf coord-accuracy {
               type decimal64 {
                 fraction-digits 6;
               }
               description
                 "The accuracy of the latitude/longitude pair for
                  ellipsoidal coordinates, or the X, Y, and Z components
                  for Cartesian coordinates.  When coord-accuracy is
                  specified, it indicates how precisely the coordinates
                  in the associated list of locations have been
                  determined with respect to the coordinate system
                  defined by the geodetic-datum.  For example, there
                  might be uncertainty due to measurement error if an
                  experimental measurement was made to determine each
                  location.";
             }
             leaf height-accuracy {
               type decimal64 {
                 fraction-digits 6;
               }
               units "meters";
               description
                 "The accuracy of the height value for ellipsoidal
                  coordinates; this value is not used with Cartesian
                  coordinates.  When height-accuracy is specified, it
                  indicates how precisely the heights in the
                  associated list of locations have been determined
                  with respect to the coordinate system defined by the
                  geodetic-datum.  For example, there might be
                  uncertainty due to measurement error if an
                  experimental measurement was made to determine each
                  location.";
             }
           }
         }
         choice location {
           description
             "The location data either in latitude/longitude or
              Cartesian values";
           case ellipsoid {
             leaf latitude {
               type decimal64 {
                 fraction-digits 16;
               }
               units "decimal degrees";
               description
                 "The latitude value on the astronomical body.  The
                  definition and precision of this measurement is
                  indicated by the reference-frame.";
             }
             leaf longitude {
               type decimal64 {
                 fraction-digits 16;
               }
               units "decimal degrees";
               description
                 "The longitude value on the astronomical body.  The
                  definition and precision of this measurement is
                  indicated by the reference-frame.";
             }
             leaf height {
               type decimal64 {
                 fraction-digits 6;
               }
               units "meters";
               description
                 "Height from a reference 0 value.  The precision and
                  '0' value is defined by the reference-frame.";
             }
           }
           case cartesian {
             leaf x {
               type decimal64 {
                 fraction-digits 6;
               }
               units "meters";
               description
                 "The X value as defined by the reference-frame.";
             }
             leaf y {
               type decimal64 {
                 fraction-digits 6;
               }
               units "meters";
               description
                 "The Y value as defined by the reference-frame.";
             }
             leaf z {
               type decimal64 {
                 fraction-digits 6;
               }
               units "meters";
               description
                 "The Z value as defined by the reference-frame.";
             }
           }
         }
         container velocity {
           description
             "If the object is in motion, the velocity vector describes
              this motion at the time given by the timestamp.  For a
              formula to convert these values to speed and heading, see
              RFC 9179.";
           reference
             "RFC 9179: A YANG Grouping for Geographic Locations";

           leaf v-north {
             type decimal64 {
               fraction-digits 12;
             }
             units "meters per second";
             description
               "v-north is the rate of change (i.e., speed) towards
                true north as defined by the geodetic-system.";
           }

           leaf v-east {
             type decimal64 {
               fraction-digits 12;
             }
             units "meters per second";
             description
               "v-east is the rate of change (i.e., speed) perpendicular
                to the right of true north as defined by
                the geodetic-system.";
           }

           leaf v-up {
             type decimal64 {
               fraction-digits 12;
             }
             units "meters per second";
             description
               "v-up is the rate of change (i.e., speed) away from the
                center of mass.";
           }
         }
         leaf timestamp {
           type yang:date-and-time;
           description
             "Reference time when location was recorded.";
         }
         leaf valid-until {
           type yang:date-and-time;
           description
             "The timestamp for which this geo-location is valid until.
              If unspecified, the geo-location has no specific
              expiration time.";
         }
       }
     }
   }
   <CODE ENDS>

4.  ISO 6709:2008 Conformance

   [ISO.6709.2008] provides an appendix with a set of tests for
   conformance to the standard.  The tests and results are given in the
   following table along with an explanation of inapplicable tests.

       +=========+===========================+====================+
       | Test    | Description               | Pass Explanation   |
       +=========+===========================+====================+
       | A.1.2.1 | elements required for a   | CRS is always      |
       |         | geographic point location | indicated          |
       +---------+---------------------------+--------------------+
       | A.1.2.2 | description of a CRS from | CRS register is    |
       |         | a register                | defined            |
       +---------+---------------------------+--------------------+
       | A.1.2.3 | definition of CRS         | N/A - Don't define |
       |         |                           | CRS                |
       +---------+---------------------------+--------------------+
       | A.1.2.4 | representation of         | latitude/longitude |
       |         | horizontal position       | values conform     |
       +---------+---------------------------+--------------------+
       | A.1.2.5 | representation of         | height value       |
       |         | vertical position         | conforms           |
       +---------+---------------------------+--------------------+
       | A.1.2.6 | text string               | N/A - No string    |
       |         | representation            | format             |
       +---------+---------------------------+--------------------+

                    Table 1: Conformance Test Results

   For test A.1.2.1, 'A.1.2.1', the YANG geo-location object either includes a
   Coordinate Reference System (CRS) (reference-frame) ('reference-frame') or has a
   default defined [WGS84].

   For A.1.2.3, 'A.1.2.3', we do not define our own CRS, and doing so is not
   required for conformance.

   For A.1.2.6, 'A.1.2.6', we do not define a text string representation, which
   is also not required for conformance.

5.  Usability

   The geo-location object defined in this document and YANG module has
   been designed to be usable in a very broad set of applications.  This
   includes the ability to locate things on astronomical bodies other
   than Earth, and to utilize entirely different coordinate systems and
   realities.

5.1.  Portability

   In order to verify portability while developing this module, the
   following standards and standard APIs were considered.

5.1.1.  IETF URI Value

   [RFC5870] defines a standard URI value for geographic location data.
   It includes the ability to specify the geodetic-value 'geodetic-value' (it calls
   this
   crs) 'crs') with the default being wgs-84 'wgs-84' [WGS84].  For the
   location data, it allows two to three coordinates defined by the crs
   'crs' value.  For accuracy, it has a single u 'u' parameter for
   specifying uncertainty.  The u 'u' value is in fractions of meters and
   applies to all the location values.  As the URI is a string, all
   values are specified as strings and so are capable of as much
   precision as required.

   URI values can be mapped to and from the YANG grouping with the
   caveat that some loss of precision (in the extremes) may occur due to
   the YANG grouping using decimal64 values rather than strings.

5.1.2.  W3C

   W3C defines a geolocation API in [W3CGEO].  We show a snippet of code
   below that defines the geolocation data for this API.  This is used
   by many applications (e.g., Google Maps API).

   interface GeolocationPosition {
     readonly attribute GeolocationCoordinates coords;
     readonly attribute DOMTimeStamp timestamp;
   };

   interface GeolocationCoordinates {
     readonly attribute double latitude;
     readonly attribute double longitude;
     readonly attribute double? altitude;
     readonly attribute double accuracy;
     readonly attribute double? altitudeAccuracy;
     readonly attribute double? heading;
     readonly attribute double? speed;
   };

              Figure 1: Snippet Showing Geolocation Definition

5.1.2.1.  Comparison with YANG Data Model

    +==================+==============+=================+=============+
    | Field            | Type         | YANG            | Type        |
    +==================+==============+=================+=============+
    | accuracy         | double       | coord-accuracy  | dec64 fr 6  |
    +------------------+--------------+-----------------+-------------+
    | altitude         | double       | height          | dec64 fr 6  |
    +------------------+--------------+-----------------+-------------+
    | altitudeAccuracy | double       | height-accuracy | dec64 fr 6  |
    +------------------+--------------+-----------------+-------------+
    | heading          | double       | v-north, v-east | dec64 fr 12 |
    +------------------+--------------+-----------------+-------------+
    | latitude         | double       | latitude        | dec64 fr 16 |
    +------------------+--------------+-----------------+-------------+
    | longitude        | double       | longitude       | dec64 fr 16 |
    +------------------+--------------+-----------------+-------------+
    | speed            | double       | v-north, v-east | dec64 fr 12 |
    +------------------+--------------+-----------------+-------------+
    | timestamp        | DOMTimeStamp | timestamp       | string      |
    +------------------+--------------+-----------------+-------------+

                                  Table 2

   accuracy (double):  Accuracy of latitude 'latitude' and longitude 'longitude' values in
      meters.

   altitude (double):  Optional height in meters above the [WGS84]
      ellipsoid.

   altitudeAccuracy (double):  Optional accuracy of altitude 'altitude' value in
      meters.

   heading (double):  Optional direction in decimal degrees from true
      north increasing clockwise.

   latitude, longitude (double):  Standard latitude/longitude values in
      decimal degrees.

   speed (double):  Speed along the heading in meters per second.

   timestamp (DOMTimeStamp):  Specifies milliseconds since the UNIX
      Epoch in a 64-bit unsigned integer.  The YANG data model defines
      the timestamp with arbitrarily large precision by using a string
      that encompasses all representable values of this timestamp value.

   W3C API values can be mapped to the YANG grouping with the caveat
   that some loss of precision (in the extremes) may occur due to the
   YANG grouping using decimal64 values rather than doubles.

   Conversely, only YANG values for Earth using the default wgs-84 'wgs-84'
   [WGS84] as the geodetic-datum 'geodetic-datum' can be directly mapped to the W3C
   values as W3C does not provide the extra features necessary to map
   the broader set of values supported by the YANG grouping.

5.1.3.  Geography Markup Language (GML)

   ISO adopted the Geography Markup Language (GML) defined by OGC 07-036
   [OGC] as [ISO.19136.2007].  GML defines, among many other things, a
   position type gml:pos, 'gml:pos', which is a sequence of double 'double' values.
   This sequence of values represents coordinates in a given CRS.  The
   CRS is either inherited from containing elements or directly
   specified as attributes srsName 'srsName' and optionally srsDimension 'srsDimension' on
   the gml:pos. 'gml:pos'.

   GML defines an Abstract CRS type from which Concrete CRS types are
   derived.  This allows for many types of CRS definitions.  We are
   concerned with the Geodetic CRS type, which can have either
   ellipsoidal or Cartesian coordinates.  We believe that other non-
   Earth-based CRSs as well as virtual CRSs should also be representable
   by the GML CRS types.

   Thus, GML gml:pos 'gml:pos' values can be mapped directly to the YANG
   grouping with the caveat that some loss of precision (in the
   extremes) may occur due to the YANG grouping using decimal64 values
   rather than doubles.

   Conversely, mapping YANG grouping values can be mapped to GML as directly as
   the GML CRS available definitions allow with a minimum of is fully supported
   for Earth-based geodetic systems fully supported. systems.

   GML also defines an observation value in gml:Observation, 'gml:Observation', which
   includes a timestamp value gml:validTime 'gml:validTime' in addition to other
   components such as gml:using gml:target 'gml:using', 'gml:target', and gml:resultOf. 'gml:resultOf'.
   Only the timestamp is mappable to and from the YANG grouping.
   Furthermore,
   gml:validTime 'gml:validTime' can either be an instantaneous measure
   (gml:TimeInstant)
   ('gml:TimeInstant') or a time period (gml:TimePeriod). ('gml:TimePeriod').  The
   instantaneous gml:TimeInstant 'gml:TimeInstant' is mappable to and from the YANG
   grouping timestamp 'timestamp' value, and values down to the resolution of
   seconds for gml:TimePeriod 'gml:TimePeriod' can be mapped using the valid-until 'valid-until'
   node of the YANG grouping.

5.1.4.  KML

   KML 2.2 [KML22] (formerly Keyhole Markup Language) was submitted by
   Google to the Open Geospatial Consortium
   (https://www.opengeospatial.org/) and was adopted.  The latest
   version as of this writing is KML 2.3 [KML23].  This schema includes
   geographic location data in some of its objects (e.g., kml:Point 'kml:Point' or
   kml:Camera
   'kml:Camera' objects).  This data is provided in string format and
   corresponds to the values specified in [W3CGEO].  The timestamp value
   is also specified as a string as in our YANG grouping.

   KML has some special handling for the height value that is useful for
   visualization software, kml:altitudeMode.  These 'kml:altitudeMode'.  The values for
   kml:altitudeMode
   'kml:altitudeMode' include indicating 'clampToGround', which indicates the
   height is ignored
   (clampToGround), in relation ignored; 'relativeToGround', which indicates the height
   value is relative to the location's ground level
   (relativeToGround), level; or in relation to 'absolute',
   which indicates the height value is an absolute value within the
   geodetic datum (absolute). datum.  The YANG grouping can directly map the ignored and
   absolute cases but not the relative-to-ground case.

   In addition to the kml:altitudeMode, 'kml:altitudeMode', KML also defines two seafloor
   height values using kml:seaFloorAltitudeMode. 'kml:seaFloorAltitudeMode'.  One value is to
   ignore the height value (clampToSeaFloor) ('clampToSeaFloor') and the other is relative
   (relativeToSeaFloor).
   ('relativeToSeaFloor').  As with the kml:altitudeMode 'kml:altitudeMode' value, the
   YANG grouping supports the ignore case but not the relative case.

   The KML location values use a geodetic datum defined in Annex A by
   the GML Coordinate Reference System (CRS) of
   [ISO.19136.2007] with identifier LonLat84_5773. 'LonLat84_5773'.  The altitude value
   for KML absolute height mode is measured from the vertical datum
   specified by [WGS84].

   Thus, the YANG grouping and KML values can be directly mapped in both
   directions (when using a supported altitude mode) with the caveat
   that some loss of precision (in the extremes) may occur due to the
   YANG grouping using decimal64 values rather than strings.  For the
   relative height cases, the application doing the transformation is
   expected to have the data available to transform the relative height
   into an absolute height, which can then be expressed using the YANG
   grouping.

6.  IANA Considerations

6.1.  Geodetic System Values Registry

   IANA has created the "Geodetic System Values" registry under the
   "YANG Geographic Location Parameters" registry.

   This registry allocates names for standard geodetic systems.  Often,
   these values are referred to using multiple names (e.g., full names
   or multiple acronyms).  The intent of this registry is to provide a
   single standard value for any given geodetic system.

   The values SHOULD use an acronym when available, they MUST be
   converted to lowercase, and spaces MUST be changed to dashes "-".

   Each entry should be sufficient to define the two coordinate values
   and to define height if height is required.  So, for example, the
   wgs-84
   'wgs-84' is defined as WGS-84 with the geoid updated by at least
   [EGM96] for height values.  Specific entries for [EGM96] and [EGM08]
   are present if a more precise definition of the data is required.

   It should be noted that [RFC5870] also created a registry for
   geodetic systems (the "'geo' URI 'crs' Parameter Values" registry);
   however, this registry has a very strict modification policy.  The
   authors of [RFC5870] have the stated goal of making CRS registration
   hard to avoid proliferation of CRS values.  As our module defines
   alternate systems and has a broader scope (i.e., beyond Earth), the
   registry defined below is meant to be more easily modified.

   The allocation policy for this registry is First Come First Served
   [RFC8126], as the intent is simply to avoid duplicate values.

   The Reference value can either be a document or a contact person as
   defined in [RFC8126].  The Change Controller (i.e., Owner) is also
   defined by [RFC8126].

   The initial values for this registry are as follows.  They include
   the non-Earth-based geodetic-datum value for the Moon based on
   [MEAN-EARTH].

     +===========+==================+===========+===================+
     | Name      | Description      | Reference | Change Controller |
     +===========+==================+===========+===================+
     | me        | Mean Earth/Polar | RFC 9179  | IETF              |
     |           | Axis (Moon)      |           |                   |
     +-----------+------------------+-----------+-------------------+
     | wgs-84-96 | World Geodetic   | RFC 9179  | IETF              |
     |           | System 1984      |           |                   |
     +-----------+------------------+-----------+-------------------+
     | wgs-84-08 | World Geodetic   | RFC 9179  | IETF              |
     |           | System 1984      |           |                   |
     +-----------+------------------+-----------+-------------------+
     | wgs-84    | World Geodetic   | RFC 9179  | IETF              |
     |           | System 1984      |           |                   |
     +-----------+------------------+-----------+-------------------+

                                 Table 3

6.2.  Updates to the IETF XML Registry

   This document registers a URI in the "IETF XML Registry" [RFC3688].
   Following the format in [RFC3688], the following registration has
   been made:

   URI:  urn:ietf:params:xml:ns:yang:ietf-geo-location
   Registrant Contact:  The IESG.
   XML:  N/A; the requested URI is an XML namespace.

6.3.  Updates to the YANG Module Names Registry

   This document registers one YANG module in the "YANG Module Names"
   registry [RFC6020].  Following the format in [RFC6020], the following
   registration has been made:

   Name:  ietf-geo-location
   Maintained by IANA:  N
   Namespace:  urn:ietf:params:xml:ns:yang:ietf-geo-location
   Prefix:  geo
   Reference:  RFC 9179

7.  Security Considerations

   The YANG module specified in this document defines a schema for data
   that is designed to be accessed via network management protocols such
   as the Network Configuration Protocol (NETCONF) [RFC6241] or RESTCONF
   [RFC8040].  The lowest NETCONF layer is the secure transport layer,
   and the mandatory-to-implement secure transport is Secure Shell (SSH)
   [RFC6242].  The lowest RESTCONF layer is HTTPS, and the mandatory-to-
   implement secure transport is TLS [RFC8446].

   The NETCONF access control model [RFC8341] provides the means to
   restrict access for particular NETCONF or RESTCONF users to a
   preconfigured subset of all available NETCONF or RESTCONF protocol
   operations and content.

   Since the modules defined in this document only define groupings,
   these considerations are primarily for the designers of other modules
   that use these groupings.

   All the data nodes defined in this YANG module are
   writable/creatable/deletable (i.e., "config true", which is the
   default).

   None of the writable/creatable/deletable data nodes in the YANG
   module defined in this document are by themselves considered more
   sensitive or vulnerable than standard configuration.

   Some of the readable data nodes in this YANG module may be considered
   sensitive or vulnerable in some network environments.  It is thus
   important to control read access (e.g., via get, get-config, or
   notification) to these data nodes.

   Since the grouping defined in this module identifies locations,
   authors using this grouping SHOULD consider any privacy issues that
   may arise when the data is readable (e.g., customer device locations,
   etc).

8.  Normative References

   [EGM08]    Pavlis, N., Holmes, S., Kenyon, S., and J. Factor, "An
              Earth Gravitational Model to Degree 2160: EGM08.",
              Presented at the 2008 General Assembly of the European
              Geosciences Union, Vienna, April 2008.

   [EGM96]    Lemoine, F., Kenyon, S., Factor, J., Trimmer, R., Pavlis,
              N., Chinn, D., Cox, C., Klosko, S., Luthcke, S., Torrence,
              M., Wang, Y., Williamson, R., Pavlis, E., Rapp, R., and T.
              Olson, "The Development of the Joint NASA GSFC and the
              National Imagery and Mapping Agency (NIMA) Geopotential
              Model EGM96.", NASA/TP-1998-206861, July 1998.

   [ISO.6709.2008]
              International Organization for Standardization, "Standard
              representation of geographic point location by
              coordinates", ISO 6709:2008, 2008.

   [MEAN-EARTH]
              NASA, "A Standardized Lunar Coordinate System for the
              Lunar Reconnaissance Orbiter", Version 4, Goddard Space
              Flight Center, May 2008.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.

   [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
              Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
              <https://www.rfc-editor.org/info/rfc6242>.

   [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
              RFC 6991, DOI 10.17487/RFC6991, July 2013,
              <https://www.rfc-editor.org/info/rfc6991>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
              Access Control Model", STD 91, RFC 8341,
              DOI 10.17487/RFC8341, March 2018,
              <https://www.rfc-editor.org/info/rfc8341>.

   [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
              and R. Wilton, "Network Management Datastore Architecture
              (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
              <https://www.rfc-editor.org/info/rfc8342>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/info/rfc8446>.

   [WGS84]    National Imagery and Mapping Agency, "Department of
              Defense World Geodetic System 1984", NIMA TR8350.2, Third
              Edition, January 2000.

9.  Informative References

   [ISO.19136.2007]
              International Organization for Standardization,
              "Geographic information -- Geography Markup Language
              (GML)", ISO 19136:2007.

   [KML22]    Wilson, T., Ed., "OGC KML", Version 2.2, April 2008,
              <https://portal.opengeospatial.org/
              files/?artifact_id=27810>.

   [KML23]    Burggraf, D., Ed., "OGC KML", Version 2.3, August 2015,
              <https://docs.opengeospatial.org/
              is/12-007r2/12-007r2.html>.

   [OGC]      OpenGIS, "OpenGIS® Geography Markup Language (GML)
              Encoding Standard", Version: 3.2.1, OGC 07-036, August
              2007, <https://portal.ogc.org/files/?artifact_id=20509>.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <https://www.rfc-editor.org/info/rfc3688>.

   [RFC5870]  Mayrhofer, A. and C. Spanring, "A Uniform Resource
              Identifier for Geographic Locations ('geo' URI)",
              RFC 5870, DOI 10.17487/RFC5870, June 2010,
              <https://www.rfc-editor.org/info/rfc5870>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <https://www.rfc-editor.org/info/rfc6020>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/info/rfc7950>.

   [RFC8340]  Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
              BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
              <https://www.rfc-editor.org/info/rfc8340>.

   [W3CGEO]   Popescu, A., "Geolocation API Specification", 2nd Edition,
              November 2016, <https://www.w3.org/TR/2016/REC-
              geolocation-API-20161108/>.

Appendix A.  Examples

   Below is a fictitious module that uses the geo-location grouping.

   module example-uses-geo-location {
     namespace
       "urn:example:example-uses-geo-location";
     prefix ugeo;
     import ietf-geo-location { prefix geo; }
     organization "Empty Org";
     contact "Example Author <eauthor@example.com>";
     description
       "Example use of geo-location";
     revision 2021-12-15 2022-2-7 { reference "None"; }
     container locatable-items {
       description
         "The container of locatable items";
       list locatable-item {
         key name;
         description
           "A locatable item";
         leaf name {
           type string;
           description
             "The name of locatable item";
         }
         uses geo:geo-location;
       }
     }
   }

              Figure 2: Example YANG Module Using Geolocation

   Below is the YANG tree for the fictitious module that uses the geo-
   location grouping.

     module: example-uses-geo-location
       +--rw locatable-items
          +--rw locatable-item* [name]
             +--rw name            string
             +--rw geo-location
                +--rw reference-frame
                |  +--rw alternate-system?    string
                |  |       {alternate-systems}?
                |  +--rw astronomical-body?   string
                |  +--rw geodetic-system
                |     +--rw geodetic-datum?    string
                |     +--rw coord-accuracy?    decimal64
                |     +--rw height-accuracy?   decimal64
                +--rw (location)?
                |  +--:(ellipsoid)
                |  |  +--rw latitude?    decimal64
                |  |  +--rw longitude?   decimal64
                |  |  +--rw height?      decimal64
                |  +--:(cartesian)
                |     +--rw x?           decimal64
                |     +--rw y?           decimal64
                |     +--rw z?           decimal64
                +--rw velocity
                |  +--rw v-north?   decimal64
                |  +--rw v-east?    decimal64
                |  +--rw v-up?      decimal64
                +--rw timestamp?         yang:date-and-time
                +--rw valid-until?       yang:date-and-time

               Figure 3: Example YANG Tree Using Geolocation

   Below is some example YANG XML data for the fictitious module that
   uses the geo-location grouping.

   <locatable-items xmlns="urn:example:example-uses-geo-location">
     <locatable-item>
       <name>Gaetana's</name>
       <geo-location>
         <latitude>40.73297</latitude>
         <longitude>-74.007696</longitude>
       </geo-location>
     </locatable-item>
     <locatable-item>
       <name>Pont des Arts</name>
       <geo-location>
         <timestamp>2012-03-31T16:00:00Z</timestamp>
         <latitude>48.8583424</latitude>
         <longitude>2.3375084</longitude>
         <height>35</height>
       </geo-location>
     </locatable-item>
     <locatable-item>
       <name>Saint Louis Cathedral</name>
       <geo-location>
         <timestamp>2013-10-12T15:00:00-06:00</timestamp>
         <latitude>29.9579735</latitude>
         <longitude>-90.0637281</longitude>
       </geo-location>
     </locatable-item>
     <locatable-item>
       <name>Apollo 11 Landing Site</name>
       <geo-location>
         <timestamp>1969-07-21T02:56:15Z</timestamp>
         <reference-frame>
           <astronomical-body>moon</astronomical-body>
           <geodetic-system>
             <geodetic-datum>me</geodetic-datum>
           </geodetic-system>
         </reference-frame>
         <latitude>0.67409</latitude>
         <longitude>23.47298</longitude>
       </geo-location>
     </locatable-item>
     <locatable-item>
       <name>Reference Frame Only</name>
       <geo-location>
         <reference-frame>
           <astronomical-body>moon</astronomical-body>
           <geodetic-system>
             <geodetic-datum>me</geodetic-datum>
           </geodetic-system>
         </reference-frame>
       </geo-location>
     </locatable-item>
   </locatable-items>

               Figure 4: Example XML Data of Geolocation Use

Acknowledgments

   We would like to thank Jim Biard and Ben Koziol for their reviews and
   suggested improvements.  We would also like to thank Peter Lothberg
   for the motivation as well as help in defining a broadly useful
   geographic location object as well as Acee Lindem and Qin Wu for
   their work on a geographic location object that led to this
   document's creation.  We would also like to thank the Document
   Shepherd Kent Watsen.

Author's Address

   Christian Hopps
   LabN Consulting, L.L.C.

   Email: chopps@chopps.org