Transport Layer Security

Internet Engineering Task Force (IETF)                         S. Whited
Request for Comments: 9266                                     July 2022
Updates: 5801, 5802, 5929, 7677 (if approved)
Intended status:
Category: Standards Track
Expires: 5 November 2022
ISSN: 2070-1721

                      Channel Bindings for TLS 1.3
          draft-ietf-kitten-tls-channel-bindings-for-tls13-16

Abstract

   This document defines a channel binding type, tls-exporter, that is
   compatible with TLS 1.3 in accordance with RFC 5056, On "On the Use of
   Channel
   Binding. Bindings to Secure Channels".  Furthermore, it updates the
   default channel binding to the new binding for versions of TLS
   greater than 1.2.  This document updates RFC5801, RFC5802, RFC5929, RFCs 5801, 5802, 5929, and RFC7677.
   7677.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list  It represents the consensus of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid the IETF community.  It has
   received public review and has been approved for a maximum publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of six months this document, any errata,
   and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 5 November 2022.
   https://www.rfc-editor.org/info/rfc9266.

Copyright Notice

   Copyright (c) 2022 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info)
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Revised BSD License text as described in Section 4.e of the
   Trust Legal Provisions and are provided without warranty as described
   in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Conventions and Terminology . . . . . . . . . . . . . . .   2
   2.  The 'tls-exporter' Channel Binding Type . . . . . . . . . . .   3
   3.  TLS 1.3 with SCRAM or GSS-API over SASL . . . . . . . . . . .   3
   4.  Security Considerations . . . . . . . . . . . . . . . . . . .   3
     4.1.  Uniqueness of Channel Bindings  . . . . . . . . . . . . .   4
     4.2.  Use with Legacy TLS . . . . . . . . . . . . . . . . . . .   5
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   5
     5.1.  Registration of Channel Binding Type  . . . . . . . . . .   5
     5.2.  Registration of Channel Binding TLS Exporter Label  . . .   6
   6.  References  . . . . . . . . . . . . . . . . . . . . . . . . .   6
     6.1.  Normative References  . . . . . . . . . . . . . . . . . .   6
     6.2.  Informative References  . . . . . . . . . . . . . . . . .   7
   Author's Address  . . . . . . . . . . . . . . . . . . . . . . . .   7

1.  Introduction

   The "tls-unique" channel binding type defined in [RFC5929] was found
   to be vulnerable susceptible to the "triple handshake vulnerability"
   [TRIPLE-HANDSHAKE] without the extended master secret extension
   defined in [RFC7627].  While TLS 1.3 uses a complete transcript hash
   akin to the extended master secret procedures, the safety of channel
   bindings with TLS 1.3 was not analyzed as part of the core protocol
   work, and so the specification of channel bindings for TLS 1.3 was
   deferred.  [RFC8446] section  Appendix C.5 of [RFC8446] notes the lack of channel
   bindings for TLS 1.3; this document defines such channel bindings, bindings and
   fills that gap.  Furthermore, this document updates [RFC5929] by
   adding an additional unique channel binding type, "tls-exporter",
   that replaces some usage of "tls-unique".

1.1.  Conventions and Terminology

   Throughout this document document, the acronym "EKM" is used to refer to
   Exported
   "Exported Keying Material Material" as defined in [RFC5705].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  The 'tls-exporter' Channel Binding Type

   Channel binding mechanisms are not useful until TLS implementations
   expose the required data.  To facilitate this, "tls-exporter" uses
   exported keying material (EKM)
   Exported Keying Material (EKM), which is already widely exposed by
   TLS implementations.  The EKM is obtained using the keying material
   exporters for TLS TLS, as defined in [RFC5705] and [RFC8446] section Section 7.5 of
   [RFC8446], by supplying the following inputs:

   Label:  The ASCII string "EXPORTER-Channel-Binding" with no
      terminating NUL.

   Context value:  Zero-length string.

   Length:  32 bytes.

   This channel binding mechanism is defined only when the TLS handshake
   results in unique master secrets.  This is true of TLS versions prior
   to 1.3 when the extended master secret extension of [RFC7627] is in
   use, and it is always true for TLS 1.3 (see [RFC8446] appendix D). Appendix D of [RFC8446]).

3.  TLS 1.3 with SCRAM or GSS-API over SASL

   SCRAM ([RFC5802], and [RFC7677])

   The specifications for Salted Challenge Response Authentication
   Mechanism (SCRAM) [RFC5802] [RFC7677] and GSS-API Generic Security Service
   Application Program Interface (GSS-API) over SASL Simple Authentication
   and Security Layer (SASL) [RFC5801] define "tls-unique" as the
   default channel binding to use over TLS.  As "tls-unique" is not
   defined for TLS 1.3 (and greater), this document updates [RFC5801],
   [RFC5802], and [RFC7677] to use "tls-
   exporter" "tls-exporter" as the default channel
   binding over TLS 1.3 (and greater).  Note that this document does not
   change the default channel binding for SCRAM mechanisms over TLS 1.2
   [RFC5246], which is still "tls-
   unique". "tls-unique" (also note that RFC 5246 has
   been obsoleted by RFC 8446).

   Additionally, this document updates the aforementioned documents to
   make "tls-exporter" the mandatory to implement mandatory-to-implement channel binding if any
   channel bindings are implemented for TLS 1.3.  Implementations that
   support channel binding over TLS 1.3 MUST implement "tls-exporter".

4.  Security Considerations

   The channel binding type defined in this document is constructed so
   that disclosure of the channel binding data does not leak secret
   information about the TLS channel and does not affect the security of
   the TLS channel.

   The derived data MUST NOT be used for any purpose other than channel
   bindings as described in [RFC5056].  In particular, implementations
   MUST NOT use channel binding as a secret key to protect privileged
   information.

   The Security Considerations sections of [RFC5056], [RFC5705], and
   [RFC8446] apply to this document.

4.1.  Uniqueness of Channel Bindings

   The definition of channel bindings in [RFC5056] defines the concept
   of a "unique" channel binding as being one that is unique to the
   channel endpoints and unique over time, that is, a value that is
   unique to a specific instance of the lower layer lower-layer security protocol.
   When TLS is the lower layer lower-layer security protocol, as for the channel
   binding type defined in this document, this concept of uniqueness
   corresponds to uniquely identifying the specific TLS connection.

   However, a stronger form of uniqueness is possible, which would
   entail uniquely identifying not just the lower layer lower-layer protocol but
   also the upper layer upper-layer application or authentication protocol that is
   consuming the channel binding.  The distinction is relevant only when
   there are multiple instances of an authentication protocol, or
   multiple distinct authentication protocols, that run atop the same
   lower layer
   lower-layer protocol.  Such a situation is rare -- rare; most consumers of
   channel bindings establish an instance of the lower layer lower-layer secure
   protocol, run a single application or authentication protocol as the
   upper layer
   upper-layer protocol, then terminate both upper and lower layer lower-layer
   protocols.  In this situation situation, the stronger form of uniqueness is
   trivially achieved, given that the channel binding value is unique in
   the sense of [RFC5056].

   The channel binding type defined by this document provides only the
   weaker type of uniqueness, as per [RFC5056]; it does not achieve the
   stronger uniqueness per upper layer the upper-layer protocol instance described
   above.  This stronger form of uniqueness would be useful in that it
   provides protection against cross-protocol attacks for the multiple
   authentication protocols running over the same instance of the lower lower-
   layer protocol, and it provides protection against replay attacks
   that seek to replay a message from one instance of an authentication
   protocol in a different instance of the same authentication protocol,
   again running over the same instance of the lower layer lower-layer protocol.
   Both of these properties are highly desirable when performing formal
   analysis of upper layer upper-layer protocols; if these properties are not
   provided, such formal analysis is essentially impossible.  In some
   cases
   cases, one or both of these properties may already be provided by
   specific upper layer upper-layer protocols, but that is dependent on the
   mechanism(s) in question, and formal analysis requires that the
   property is provided in a generic manner, manner across all potential upper upper-
   layer protocols that exist or might exist in the future.

   Accordingly, applications that make use of the channel binding type
   defined in this document MUST NOT use the channel binding for more
   than one authentication mechanism instance on a given TLS connection.
   Such applications MUST immediately close the TLS connection after the
   conclusion of the upper layer upper-layer protocol.

4.2.  Use with Legacy TLS

   While it is possible to use this channel binding mechanism with TLS
   versions below 1.3, extra precaution must be taken to ensure that the
   chosen cipher suites always result in unique master secrets.  For
   more information information, see [RFC7627] and the Security Considerations
   section of [RFC5705] (TLS 1.3 always provides unique master secrets,
   as discussed in Appendix D of [RFC8446].) [RFC8446]).

   When TLS renegotiation is enabled on a connection connection, the "tls-exporter"
   channel binding type is not defined for that connection connection, and
   implementations MUST NOT support it.

   In general, users wishing to take advantage of channel binding should
   upgrade to TLS 1.3 or later.

5.  IANA Considerations

5.1.  Registration of Channel Binding Type

   This document adds the following registration

   IANA has registered tls-exporter in the "Channel-Binding Types"
   registry:

   Subject:  Registration of channel binding tls-exporter

   Channel binding

   Channel-binding unique prefix:  tls-exporter

   Channel binding

   Channel-binding type:  unique

   Channel type:  TLS [RFC8446]

   Published specification:  draft-ietf-kitten-tls-channel-bindings-for-
      tls13-16

   Channel binding  RFC 9266

   Channel-binding is secret:  no

   Description:  The EKM value obtained from the current TLS connection.

   Intended usage:  COMMON

   Person and email address to contact for further information:  Sam
      Whited <sam@samwhited.com>. <sam@samwhited.com>

   Owner/Change controller name and email address:  IESG.  IESG

   Expert reviewer name and contact information:  IETF KITTEN WG
      <kitten@ietf.org> or IETF TLS WG
      (kitten@ietf.org or tls@ietf.org, failing that, ietf@ietf.org). <tls@ietf.org>

   Note:  See the published specification for advice on the
      applicability of this channel binding type.

5.2.  Registration of Channel Binding TLS Exporter Label

   This document adds

   IANA has added the following registration in the "TLS Exporter
   Labels" registry, which is part of registry under the "Transport Layer Security (TLS)
   Parameters" group: registry:

   Value:  EXPORTER-Channel-Binding

   DTLS-OK:  Y

   Recommended:  Y

   Reference:  This document  RFC 9266

6.  References

6.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC5056]  Williams, N., "On the Use of Channel Bindings to Secure
              Channels", RFC 5056, DOI 10.17487/RFC5056, November 2007,
              <https://www.rfc-editor.org/info/rfc5056>.

   [RFC5705]  Rescorla, E., "Keying Material Exporters for Transport
              Layer Security (TLS)", RFC 5705, DOI 10.17487/RFC5705,
              March 2010, <https://www.rfc-editor.org/info/rfc5705>.

   [RFC5801]  Josefsson, S. and N. Williams, "Using Generic Security
              Service Application Program Interface (GSS-API) Mechanisms
              in Simple Authentication and Security Layer (SASL): The
              GS2 Mechanism Family", RFC 5801, DOI 10.17487/RFC5801,
              July 2010, <https://www.rfc-editor.org/info/rfc5801>.

   [RFC5802]  Newman, C., Menon-Sen, A., Melnikov, A., and N. Williams,
              "Salted Challenge Response Authentication Mechanism
              (SCRAM) SASL and GSS-API Mechanisms", RFC 5802,
              DOI 10.17487/RFC5802, July 2010,
              <https://www.rfc-editor.org/info/rfc5802>.

   [RFC5929]  Altman, J., Williams, N., and L. Zhu, "Channel Bindings
              for TLS", RFC 5929, DOI 10.17487/RFC5929, July 2010,
              <https://www.rfc-editor.org/info/rfc5929>.

   [RFC7677]  Hansen, T., "SCRAM-SHA-256 and SCRAM-SHA-256-PLUS Simple
              Authentication and Security Layer (SASL) Mechanisms",
              RFC 7677, DOI 10.17487/RFC7677, November 2015,
              <https://www.rfc-editor.org/info/rfc7677>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/info/rfc8446>.

6.2.  Informative References

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <https://www.rfc-editor.org/info/rfc5246>.

   [RFC7627]  Bhargavan, K., Ed., Delignat-Lavaud, A., Pironti, A.,
              Langley, A., and M. Ray, "Transport Layer Security (TLS)
              Session Hash and Extended Master Secret Extension",
              RFC 7627, DOI 10.17487/RFC7627, September 2015,
              <https://www.rfc-editor.org/info/rfc7627>.

   [TRIPLE-HANDSHAKE]
              Bhargavan, K., Delignat-Lavaud, A., Fournet, C., Pironti,
              A., and P. Strub, "Password Storage", "Triple Handshakes Considered Harmful:
              Breaking and Fixing Authentication over TLS", March 2014,
              <https://www.mitls.org/pages/attacks/3SHAKE>.

Author's Address

   Sam Whited
   Atlanta, GA
   United States of America
   Email: sam@samwhited.com
   URI:   https://blog.samwhited.com/