Internet Engineering Task Force (IETF)                           E. Chen
Request for Comments: 9468                            Palo Alto Networks
Category: Standards Track                                        N. Shen
ISSN: 2070-1721                                                   Zededa
                                                               R. Raszuk
                                                                  Arrcus
                                                               R. Rahman
                                                                 Equinix
                                                             August 2023

  Unsolicited Bidirectional Forwarding Detection (BFD) for Sessionless
                              Applications

Abstract

   For operational simplification of "sessionless" applications using
   Bidirectional Forwarding Detection (BFD), in this document, we
   present procedures for "unsolicited BFD" that allow a BFD session to
   be initiated by only one side and established without explicit per-
   session configuration or registration by the other side (subject to
   certain per-interface or global policies).

   We also introduce a new YANG module to configure and manage
   "unsolicited BFD".  The YANG module in this document is based on YANG
   1.1, as defined in RFC 7950, and conforms to the Network Management
   Datastore Architecture (NMDA), as described in RFC 8342.  This
   document augments RFC 9314.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9468.

Copyright Notice

   Copyright (c) 2023 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Revised BSD License text as described in Section 4.e of the
   Trust Legal Provisions and are provided without warranty as described
   in the Revised BSD License.

Table of Contents

   1.  Introduction
     1.1.  Requirements Language
   2.  Procedures for Unsolicited BFD
   3.  State Variables
   4.  YANG Data Model
     4.1.  Unsolicited BFD Hierarchy
     4.2.  Unsolicited BFD Module
     4.3.  Data Model Example
   5.  IANA Considerations
   6.  Security Considerations
     6.1.  BFD Protocol Security Considerations
     6.2.  BFD Protocol Authentication Considerations
     6.3.  YANG Module Security Considerations
   7.  References
     7.1.  Normative References
     7.2.  Informative References
   Acknowledgments
   Authors' Addresses

1.  Introduction

   The current implementation and deployment practice for BFD ([RFC5880]
   and [RFC5881]) usually requires that BFD sessions be explicitly
   configured or registered on both sides.  This requirement is not an
   issue when an application like BGP [RFC4271] has the concept of a
   "session" that involves both sides for its establishment.  However,
   this requirement can be operationally challenging when the
   prerequisite "session" does not naturally exist between two endpoints
   in an application.  Simultaneous configuration and coordination may
   be required on both sides for BFD to take effect.  For example:

   *  When BFD is used to keep track of the "liveness" of the next hop
      of static routes.  Although only one side may need the BFD
      functionality, currently, both sides need to be involved in
      specific configuration and coordination, and in some cases, static
      routes are created unnecessarily just for BFD.

   *  When BFD is used to keep track of the "liveness" of the third-
      party next hop of BGP routes received from the Route Server
      [RFC7947] at an Internet Exchange Point (IXP).  As the third-party
      next hop is different from the peering address of the Route
      Server, for BFD to work, currently, two routers peering with the
      Route Server need to have routes and next hops from each other
      (although indirectly via the Route Server).

   Clearly, it is beneficial and desirable to reduce or eliminate
   unnecessary configurations and coordination in these "sessionless"
   applications using BFD.

   In this document, we present procedures for "unsolicited BFD" that
   allow a BFD session to be initiated by only one side and established
   without explicit per-session configuration or registration by the
   other side (subject to certain per-interface or global policies).

   Unsolicited BFD impacts only the initiation of BFD sessions.  There
   is no change to all the other procedures specified in [RFC5880], such
   as, but not limited to, the Echo function and Demand mode.

   With "unsolicited BFD", there is potential risk for excessive
   resource usage by BFD from "unexpected" remote systems.  To mitigate
   such risks, several mechanisms are recommended in the Security
   Considerations section.

   The procedure described in this document could be applied to BFD for
   multihop paths [RFC5883].  However, because of security risks, this
   document applies only to BFD for single IP hops [RFC5881].

   Compared to the "Seamless BFD" [RFC7880], this proposal involves only
   minor procedural enhancements to the widely deployed BFD itself.
   Thus, we believe that this proposal is inherently simpler in the
   protocol itself and deployment.  As an example, it does not require
   the exchange of BFD discriminators over an out-of-band channel before
   BFD session bring-up.

   When BGP ADD-PATH [RFC7911] is deployed at an IXP using a Route
   Server, multiple BGP paths (when they exist) can be made available to
   the clients of the Route Server, as described in [RFC7947].
   Unsolicited BFD can be used by BGP route selection's route
   resolvability condition (Section 9.1.2.1 of [RFC4271]) to exclude
   routes where the NEXT_HOP is not reachable using the procedures
   specified in this document.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  Procedures for Unsolicited BFD

   With "unsolicited BFD", one side takes the "Active role" and the
   other side takes the "Passive role", as described in [RFC5880],
   Section 6.1.

   Passive unsolicited BFD support MUST be disabled by default and MUST
   require explicit configuration to be enabled.  On the passive side,
   the following BFD parameters, from [RFC5880], Section 6.8.1, SHOULD
   be configurable:

   *  bfd.DesiredMinTxInterval

   *  bfd.RequiredMinRxInterval

   *  bfd.DetectMult

   The passive side MAY also choose to use the values of the parameters
   listed above that the active side uses in its BFD Control packets.
   However, the bfd.LocalDiscr value MUST be selected by the passive
   side to allow multiple unsolicited BFD sessions.

   The active side starts sending the BFD Control packets, as specified
   in [RFC5880].  The passive side does not send BFD Control packets
   initially; it sends BFD Control packets only after it has received
   BFD Control packets from the active side.

   When the passive side receives a BFD Control packet from the active
   side with 0 as "Your Discriminator" and does not find an existing BFD
   session, the passive side SHOULD create a matching BFD session toward
   the active side, unless not permitted by local configuration or
   policy.

   When the passive side receives an incoming BFD Control packet on a
   numbered interface, the source address of that packet MUST belong to
   the subnet of the interface on which the BFD packet is received, else
   the BFD Control packet MUST NOT be processed.

   The passive side MUST then start sending BFD Control packets and
   perform the necessary procedure for bringing up, maintaining, and
   tearing down the BFD session.  If the BFD session fails to get
   established within a certain amount of time (which is implementation
   specific but has to be at least equal to the local failure detection
   time) or if an established BFD session goes down, the passive side
   MUST stop sending BFD Control packets and SHOULD delete the BFD
   session created until BFD Control packets are initiated by the active
   side again.

   When an unsolicited BFD session goes down, an implementation may
   retain the session state for a period of time.  Retaining this state
   can be useful for operational purposes.

3.  State Variables

   This document defines a new state variable called Role:

   bfd.Role

   This is the role of the local system during BFD session
   initialization, as per [RFC5880], Section 6.1.  Possible values are
   Active or Passive.

4.  YANG Data Model

   This section extends the YANG data model for BFD [RFC9314] to cover
   unsolicited BFD.  The new module imports the YANG modules described
   in [RFC8349] since the "bfd" container in [RFC9314] is under
   "control-plane-protocol".  The YANG module in this document conforms
   to the Network Management Datastore Architecture (NMDA) [RFC8342].

4.1.  Unsolicited BFD Hierarchy

   Configuration for unsolicited BFD parameters for IP single-hop
   sessions can be done at 2 levels:

   *  globally, i.e., for all interfaces

   *  for specific interfaces (this requires support for the
      "unsolicited-params-per-interface" feature)

   If configuration exists at both levels, per-interface configuration
   takes precedence over global configuration.

   For operational data, a new "role" leaf node has been added for BFD
   IP single-hop sessions.

   The tree diagram below uses the graphical representation of data
   models, as defined in [RFC8340].

   module: ietf-bfd-unsolicited

     augment /rt:routing/rt:control-plane-protocols
             /rt:control-plane-protocol/bfd:bfd/bfd-ip-sh:ip-sh:
       +--rw unsolicited?
          +--rw local-multiplier?                 multiplier
          +--rw (interval-config-type)?
             +--:(tx-rx-intervals)
             |  +--rw desired-min-tx-interval?    uint32
             |  +--rw required-min-rx-interval?   uint32
             +--:(single-interval) {single-minimum-interval}?
                +--rw min-interval?               uint32
     augment /rt:routing/rt:control-plane-protocols
             /rt:control-plane-protocol/bfd:bfd/bfd-ip-sh:ip-sh
             /bfd-ip-sh:interfaces:
       +--rw unsolicited
          +--rw enabled?                          boolean
          +--rw local-multiplier?
               bfd-types:multiplier
                {bfd-unsol:unsolicited-params-per-interface}?
          +--rw (interval-config-type)?
                  {bfd-unsol:unsolicited-params-per-interface}?
             +--:(tx-rx-intervals)
             |  +--rw desired-min-tx-interval?    uint32
             |  +--rw required-min-rx-interval?   uint32
             +--:(single-interval) {bfd-types:single-minimum-interval}?
                +--rw min-interval?               uint32
     augment /rt:routing/rt:control-plane-protocols
             /rt:control-plane-protocol/bfd:bfd/bfd-ip-sh:ip-sh
             /bfd-ip-sh:sessions/bfd-ip-sh:session:
       +--ro role?   bfd-unsol:role

4.2.  Unsolicited BFD Module

   <CODE BEGINS> file "ietf-bfd-unsolicited@2023-08-16.yang"
   module ietf-bfd-unsolicited {

     yang-version 1.1;

     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd-unsolicited";

     prefix bfd-unsol;

     import ietf-bfd-types {
       prefix bfd-types;
       reference
         "RFC 9314: YANG Data Model for Bidirectional Forwarding
          Detection (BFD)";
     }

     import ietf-bfd {
       prefix bfd;
       reference
         "RFC 9314: YANG Data Model for Bidirectional Forwarding
          Detection (BFD)";
     }

     import ietf-bfd-ip-sh {
       prefix bfd-ip-sh;
       reference
         "RFC 9314: YANG Data Model for Bidirectional Forwarding
          Detection (BFD)";
     }

     import ietf-routing {
       prefix rt;
       reference
         "RFC 8349: A YANG Data Model for Routing Management
          (NMDA Version)";
     }

     organization
       "IETF BFD Working Group";

     contact
       "WG Web:   <https://datatracker.ietf.org/wg/bfd/>
        WG List:  <rtg-bfd@ietf.org>

        Editors:  Enke Chen (enchen@paloaltonetworks.com),
                  Naiming Shen (naiming@zededa.com),
                  Robert Raszuk (robert@raszuk.net),
                  Reshad Rahman (reshad@yahoo.com)";

     description
       "This module contains the YANG definition for unsolicited BFD,
        as per RFC 9468.

        Copyright (c) 2023 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Revised BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC 9468; see
        the RFC itself for full legal notices.";

     reference
       "RFC 9468: Unsolicited Bidirectional Forwarding Detection
        (BFD) for Sessionless Applications";

     revision 2023-08-16 {
       description
         "Initial revision.";
       reference
         "RFC 9468: Unsolicited Bidirectional Forwarding Detection (BFD)
          for Sessionless Applications";
     }

     /*
      * Feature definitions
      */
     feature unsolicited-params-per-interface {
       description
         "This feature indicates that the server supports per-interface
          parameters for unsolicited sessions.";
       reference
         "RFC 9468: Unsolicited Bidirectional Forwarding Detection (BFD)
          for Sessionless Applications";
     }

     /*
      * Type Definitions
      */

     identity role {
       description
         "Base identity from which all roles are derived.
          Role of local system during BFD session initialization.";
     }

     identity active {
       base bfd-unsol:role;
       description
         "Active role.";
       reference
         "RFC 5880: Bidirectional Forwarding Detection (BFD),
          Section 6.1";
     }

     identity passive {
       base bfd-unsol:role;
       description
         "Passive role.";
       reference
         "RFC 5880: Bidirectional Forwarding Detection (BFD),
          Section 6.1";
     }

     /*
      * Augments
      */

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd/bfd-ip-sh:ip-sh" {
       description
         "Augmentation for unsolicited BFD parameters.";
       container unsolicited {
         description
           "BFD IP single-hop unsolicited top-level container.";
         uses bfd-types:base-cfg-parms;
       }
     }

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd/bfd-ip-sh:ip-sh/"
           + "bfd-ip-sh:interfaces" {
       description
         "Augmentation for unsolicited BFD on IP single-hop
          interface.";
       container unsolicited {
         description
           "BFD IP single-hop interface unsolicited top-level
            container.";
         leaf enabled {
           type boolean;
           default "false";
           description
             "Unsolicited BFD is enabled on this interface.";
         }
         /*
          * The following is the same as bfd-types:base-cfg-parms, but
          * without default values (for inheritance)
          */
         leaf local-multiplier {
           if-feature "bfd-unsol:unsolicited-params-per-interface";
           type bfd-types:multiplier;
           description
             "Multiplier transmitted by the local system.  Defaults to
              ../../unsolicited/local-multiplier.
              A multiplier configured under an interface takes
              precedence over the multiplier configured at the global
              level.";
         }
         choice interval-config-type {
           if-feature "bfd-unsol:unsolicited-params-per-interface";
           description
             "Two interval values or one value used for both transmit
              and receive.  Defaults to
              ../../unsolicited/interval-config-type.  An interval
              configured under an interface takes precedence over any
              interval configured at the global level.";
           case tx-rx-intervals {
             leaf desired-min-tx-interval {
               type uint32;
               units "microseconds";
               description
                 "Desired minimum transmit interval of control
                  packets.";
             }
             leaf required-min-rx-interval {
               type uint32;
               units "microseconds";
               description
                 "Required minimum receive interval of control
                  packets.";
             }
           }
           case single-interval {
             if-feature "bfd-types:single-minimum-interval";
             leaf min-interval {
               type uint32;
               units "microseconds";
               description
                 "Desired minimum transmit interval and required
                  minimum receive interval of control packets.";
             }
           }
         }
       }
     }

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd/bfd-ip-sh:ip-sh/"
           + "bfd-ip-sh:sessions/bfd-ip-sh:session" {
       description
         "Augmentation for unsolicited BFD on IP single-hop session.";
       leaf role {
         type identityref {
           base bfd-unsol:role;
         }
         config false;
         description
           "Role.";
       }
     }
   }
   <CODE ENDS>

4.3.  Data Model Example

   This section shows an example on how to configure the passive end of
   unsolicited BFD:

   *  We have global BFD IP single-hop unsolicited configuration with a
      local-multiplier of 2 and min-interval at 50 ms.

   *  BFD IP single-hop unsolicited is enabled on interface eth0 with a
      local-multiplier of 3 and min-interval at 250 ms.

   *  BFD IP single-hop unsolicited is enabled on interface eth1.  Since
      there is no parameter configuration for eth1, it inherits from the
      global configuration.

   <?xml version="1.0" encoding="UTF-8"?>
   <config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
   <interfaces xmlns="urn:ietf:params:xml:ns:yang:ietf-interfaces">
     <interface>
       <name>eth0</name>
       <type
           xmlns:ianaift="urn:ietf:params:xml:ns:yang:iana-if-type">
            ianaift:ethernetCsmacd</type>
     </interface>
     <interface>
       <name>eth1</name>
       <type
           xmlns:ianaift="urn:ietf:params:xml:ns:yang:iana-if-type">
            ianaift:ethernetCsmacd</type>
     </interface>
   </interfaces>
   <routing xmlns="urn:ietf:params:xml:ns:yang:ietf-routing">
     <control-plane-protocols>
       <control-plane-protocol>
         <type
             xmlns:bfd-types="urn:ietf:params:xml:ns:yang:ietf-bfd-types"> xmlns:bfd-types=
           "urn:ietf:params:xml:ns:yang:ietf-bfd-types">
            bfd-types:bfdv1</type>
         <name>name:BFD</name>
         <bfd xmlns="urn:ietf:params:xml:ns:yang:ietf-bfd">
           <ip-sh xmlns="urn:ietf:params:xml:ns:yang:ietf-bfd-ip-sh">
             <unsolicited>
               <local-multiplier>2</local-multiplier>
               <min-interval>50000</min-interval>
             </unsolicited>
             <interfaces>
                 <interface>eth0</interface>
                 <unsolicited>
                   <enabled>true</enabled>
                   <local-multiplier>3</local-multiplier>
                   <min-interval>250000</min-interval>
                 </unsolicited>
             </interfaces>
             <interfaces>
                 <interface>eth1</interface>
                 <unsolicited>
                   <enabled>true</enabled>
                 </unsolicited>
             </interfaces>
           </ip-sh>
         </bfd>
       </control-plane-protocol>
     </control-plane-protocols>
   </routing>
   </config>

5.  IANA Considerations

   IANA has registered the following namespace URI in the "ns"
   subregistry within the "IETF XML Registry" [RFC3688]:

   URI:  urn:ietf:params:xml:ns:yang:ietf-bfd-unsolicited
   Registrant Contact:  The IESG.
   XML:  N/A; the requested URI is an XML namespace.

   IANA has registered the following YANG module in the "YANG Module
   Names" registry [RFC6020]:

   Name:  ietf-bfd-unsolicited
   Maintained by IANA:  N
   Namespace:  urn:ietf:params:xml:ns:yang:ietf-bfd-unsolicited
   Prefix:  bfd-unsol
   Reference:  RFC 9468

6.  Security Considerations

6.1.  BFD Protocol Security Considerations

   The same security considerations and protection measures as those
   described in [RFC5880] and [RFC5881] apply to this document.  In
   addition, with "unsolicited BFD", there is potential risk for
   excessive resource usage by BFD from "unexpected" remote systems.  To
   mitigate such risks, implementations of unsolicited BFD MUST:

   *  Limit the feature to specific interfaces and to single-hop BFD
      sessions using the procedures from [RFC5082].  See Section 5 of
      [RFC5881] for the details of these procedures.

   *  Apply policy to process BFD packets only from certain subnets or
      hosts.

   *  Deploy the feature only in an environment that does not offer
      anonymous participation.  Examples include an IXP, where the IXP
      operator will have a business relationship with all IXP
      participants, or between a provider and its customers.

6.2.  BFD Protocol Authentication Considerations

   Implementations of unsolicited BFD are RECOMMENDED to use BFD
   authentication; see [RFC5880].  If BFD authentication is used, the
   strongest BFD authentication mechanism that is supported MUST be
   used.

   In some environments, such as IXPs, BFD authentication cannot be used
   because of the lack of coordination for the operation of the two
   endpoints of the BFD session.

   In other environments, such as when BFD is used to track the next hop
   of static routes, it is possible to use BFD authentication.  This
   comes with the extra cost of configuring matching key chains between
   the two endpoints.

6.3.  YANG Module Security Considerations

   The YANG module specified in this document defines a schema for data
   that is designed to be accessed via network management protocols such
   as NETCONF [RFC6241] or RESTCONF [RFC8040].  The lowest NETCONF layer
   is the secure transport layer, and the mandatory-to-implement secure
   transport is Secure Shell (SSH) [RFC6242].  The lowest RESTCONF layer
   is HTTPS, and the mandatory-to-implement secure transport is TLS
   [RFC8446].

   The Network Configuration Access Control Mode (NACM) [RFC8341]
   provides the means to restrict access for particular NETCONF or
   RESTCONF users to a preconfigured subset of all available NETCONF or
   RESTCONF protocol operations and content.

   There are a number of data nodes defined in this YANG module that are
   writable/creatable/deletable (i.e., config true, which is the
   default).  These data nodes may be considered sensitive or vulnerable
   in some network environments.  Write operations (e.g., edit-config)
   to these data nodes without proper protection can have a negative
   effect on network operations.  These are the subtrees and data nodes
   and their sensitivity/vulnerability:

   /routing/control-plane-protocols/control-plane-protocol/bfd/ip-sh
   /unsolicited:
      *  Data node "enabled" enables creation of unsolicited BFD IP
         single-hop sessions globally, i.e., on all interfaces.  See
         Section 6.1.

      *  Data nodes "local-multiplier", "desired-min-tx-interval",
         "required-min-rx-interval", and "min-interval" all impact the
         parameters of the unsolicited BFD IP single-hop sessions.
         Write operations to these nodes change the rates of BFD packet
         generation and detection time of the failures of a BFD session.

   /routing/control-plane-protocols/control-plane-protocol/bfd/ip-sh
   /interfaces/interface/unsolicited:
      *  Data node "enabled" enables the creation of unsolicited BFD IP
         single-hop sessions on a specific interface.  See Section 6.1.

      *  Data nodes "local-multiplier", "desired-min-tx-interval",
         "required-min-rx-interval", and "min-interval" all impact the
         parameters of the unsolicited BFD IP single-hop sessions on the
         interface.

   Some of the readable data nodes in this YANG module may be considered
   sensitive or vulnerable in some network environments.  It is thus
   important to control read access (e.g., via get, get-config, or
   notification) to these data nodes.  These are the subtrees and data
   nodes and their sensitivity/vulnerability:

   /routing/control-plane-protocols/control-plane-protocol/bfd/ip-sh
   /sessions/session/role:
      Access to this information discloses the role of the local system
      in the creation of the unsolicited BFD session.

7.  References

7.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <https://www.rfc-editor.org/info/rfc3688>.

   [RFC5082]  Gill, V., Heasley, J., Meyer, D., Savola, P., Ed., and C.
              Pignataro, "The Generalized TTL Security Mechanism
              (GTSM)", RFC 5082, DOI 10.17487/RFC5082, October 2007,
              <https://www.rfc-editor.org/info/rfc5082>.

   [RFC5880]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,
              <https://www.rfc-editor.org/info/rfc5880>.

   [RFC5881]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD) for IPv4 and IPv6 (Single Hop)", RFC 5881,
              DOI 10.17487/RFC5881, June 2010,
              <https://www.rfc-editor.org/info/rfc5881>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <https://www.rfc-editor.org/info/rfc6020>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.

   [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
              Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
              <https://www.rfc-editor.org/info/rfc6242>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8340]  Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
              BCP 215, RFC 8340, DOI 10.17487/RFC8340, March 2018,
              <https://www.rfc-editor.org/info/rfc8340>.

   [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
              Access Control Model", STD 91, RFC 8341,
              DOI 10.17487/RFC8341, March 2018,
              <https://www.rfc-editor.org/info/rfc8341>.

   [RFC8349]  Lhotka, L., Lindem, A., and Y. Qu, "A YANG Data Model for
              Routing Management (NMDA Version)", RFC 8349,
              DOI 10.17487/RFC8349, March 2018,
              <https://www.rfc-editor.org/info/rfc8349>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/info/rfc8446>.

   [RFC9314]  Jethanandani, M., Ed., Rahman, R., Ed., Zheng, L., Ed.,
              Pallagatti, S., and G. Mirsky, "YANG Data Model for
              Bidirectional Forwarding Detection (BFD)", RFC 9314,
              DOI 10.17487/RFC9314, September 2022,
              <https://www.rfc-editor.org/info/rfc9314>.

7.2.  Informative References

   [RFC4271]  Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
              Border Gateway Protocol 4 (BGP-4)", RFC 4271,
              DOI 10.17487/RFC4271, January 2006,
              <https://www.rfc-editor.org/info/rfc4271>.

   [RFC5883]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD) for Multihop Paths", RFC 5883, DOI 10.17487/RFC5883,
              June 2010, <https://www.rfc-editor.org/info/rfc5883>.

   [RFC7880]  Pignataro, C., Ward, D., Akiya, N., Bhatia, M., and S.
              Pallagatti, "Seamless Bidirectional Forwarding Detection
              (S-BFD)", RFC 7880, DOI 10.17487/RFC7880, July 2016,
              <https://www.rfc-editor.org/info/rfc7880>.

   [RFC7911]  Walton, D., Retana, A., Chen, E., and J. Scudder,
              "Advertisement of Multiple Paths in BGP", RFC 7911,
              DOI 10.17487/RFC7911, July 2016,
              <https://www.rfc-editor.org/info/rfc7911>.

   [RFC7947]  Jasinska, E., Hilliard, N., Raszuk, R., and N. Bakker,
              "Internet Exchange BGP Route Server", RFC 7947,
              DOI 10.17487/RFC7947, September 2016,
              <https://www.rfc-editor.org/info/rfc7947>.

   [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
              and R. Wilton, "Network Management Datastore Architecture
              (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
              <https://www.rfc-editor.org/info/rfc8342>.

Acknowledgments

   The authors would like to thank Acee Lindem, Alvaro Retana, Dan
   Romascanu, Derek Atkins, Greg Mirsky, Gyan Mishra, Henning Rogge,
   Jeffrey Haas, John Scudder, Lars Eggert, Magnus Westerlund, Mahesh
   Jethanandani, Murray Kucherawy, Raj Chetan, Robert Wilton, Roman
   Danyliw, Tom Petch, and Zaheduzzaman Sarker for their reviews and
   valuable input.

Authors' Addresses

   Enke Chen
   Palo Alto Networks
   3000 Tannery Way
   Santa Clara, CA 95054
   United States of America
   Email: enchen@paloaltonetworks.com

   Naiming Shen
   Zededa
   160 W Santa Clara Street
   San Jose, CA 95113
   United States of America
   Email: naiming@zededa.com

   Robert Raszuk
   Arrcus
   2077 Gateway Place
   San Jose, CA 95110
   United States of America
   Email: robert@raszuk.net

   Reshad Rahman
   Equinix
   Canada
   Email: reshad@yahoo.com