Inter-Domain Routing

Internet Engineering Task Force (IETF)                          G. Dawra
Internet-Draft
Request for Comments: 9514                                      LinkedIn
Intended status:
Category: Standards Track                                    C. Filsfils
Expires: 21 August 2023
ISSN: 2070-1721                                       K. Talaulikar, Ed.
                                                           Cisco Systems
                                                                 M. Chen
                                                                  Huawei
                                                              D. Bernier
                                                             Bell Canada
                                                             B. Decraene
                                                                  Orange
                                                        17 February
                                                           November 2023

                   BGP

  Border Gateway Protocol - Link State (BGP-LS) Extensions for SRv6
                    draft-ietf-idr-bgpls-srv6-ext-14 Segment
                        Routing over IPv6 (SRv6)

Abstract

   Segment Routing over IPv6 (SRv6) allows for a flexible definition of
   end-to-end paths within various topologies by encoding paths as
   sequences of topological or functional sub-paths, sub-paths called "segments".
   These segments are advertised by various protocols such as BGP, IS-IS IS-
   IS, and OSPFv3.

   This document defines extensions to BGP Link-state - Link State (BGP-LS) to
   advertise SRv6 segments along with their behaviors and other
   attributes via BGP.  The BGP-LS address-family solution for SRv6
   described in this document is similar to BGP-LS for SR for the MPLS
   data-plane
   data plane, which is defined in a separate document. RFC 9085.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list  It represents the consensus of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid the IETF community.  It has
   received public review and has been approved for a maximum publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of six months RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be updated, replaced, or obsoleted by other documents obtained at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 21 August 2023.
   https://www.rfc-editor.org/info/rfc9514.

Copyright Notice

   Copyright (c) 2023 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info)
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Revised BSD License text as described in Section 4.e of the
   Trust Legal Provisions and are provided without warranty as described
   in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  BGP-LS Extensions for SRv6  . . . . . . . . . . . . . . . . .   4
   3.  SRv6 Node Attributes  . . . . . . . . . . . . . . . . . . . .   5
     3.1.  SRv6 Capabilities TLV . . . . . . . . . . . . . . . . . .   5
     3.2.  SRv6 Node MSD Types . . . . . . . . . . . . . . . . . . .   6
   4.  SRv6 Link Attributes  . . . . . . . . . . . . . . . . . . . .   7
     4.1.  SRv6 End.X SID TLV  . . . . . . . . . . . . . . . . . . .   7
     4.2.  SRv6 LAN End.X SID TLV  . . . . . . . . . . . . . . . . .   9
     4.3.  SRv6 Link MSD Types . . . . . . . . . . . . . . . . . . .  11
   5.  SRv6 Prefix Attributes  . . . . . . . . . . . . . . . . . . .  11
     5.1.  SRv6 Locator TLV  . . . . . . . . . . . . . . . . . . . .  11
   6.  SRv6 SID NLRI . . . . . . . . . . . . . . . . . . . . . . . .  13
     6.1.  SRv6 SID Information TLV  . . . . . . . . . . . . . . . .  14
   7.  SRv6 SID Attributes . . . . . . . . . . . . . . . . . . . . .  15
     7.1.  SRv6 Endpoint Behavior TLV  . . . . . . . . . . . . . . .  15
     7.2.  SRv6 BGP Peer Node PeerNode SID TLV  . . . . . . . . . . . . . . .  16
   8.  SRv6 SID Structure TLV  . . . . . . . . . . . . . . . . . . .  18
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  19
     9.1.  BGP-LS NLRI-Types . . . . . . . . . . . . . . . . . . . .  19 NLRI Types
     9.2.  BGP-LS NLRI and Attribute TLVs . . . . . . . . . . . . . . . . . . . . . . .  19
     9.3.  SRv6 BGP EPE SID Flags  . . . . . . . . . . . . . . . . .  19
   10. Manageability Considerations  . . . . . . . . . . . . . . . .  20
   11. Security Considerations . . . . . . . . . . . . . . . . . . .  21
   12. Contributors  . . . . . . . . . . . . . . . . . . . . . . . .  21
   13. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  22
   14. References  . . . . . . . . . . . . . . . . . . . . . . . . .  22
     14.1.
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  22
     14.2.
     12.2.  Informative References . . . . . . . . . . . . . . . . .  24
   Appendix A.  Differences with BGP-EPE for SR-MPLS . . . . . . . .  24
   Acknowledgements
   Contributors
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  25

1.  Introduction

   SRv6 refers to Segment Routing instantiated on the IPv6 data-plane data plane
   [RFC8402].  An SRv6 Segment segment is often referred to by its SRv6 Segment
   Identifier (SID).

   The network programming paradigm [RFC8986] is central to SRv6.  It
   describes how different behaviors can be bound to SIDs and how a
   network program can be expressed as a combination of SIDs.

   An SRv6-capable node maintains all the SRv6 segments explicitly
   instantiated locally.

   The IS-IS and OSPFv3 link-state routing protocols have been extended
   to advertise some of these SRv6 SIDs and SRv6-related information
   [I-D.ietf-lsr-isis-srv6-extensions],
   [I-D.ietf-lsr-ospfv3-srv6-extensions].
   [RFC9352] [RFC9513].  Other SRv6 SIDs may be instantiated on a node
   via other mechanisms for topological or service functionalities.

   The advertisement of SR related SR-related information along with the topology
   for the MPLS data-plane instantiation (SR-MPLS)
   is specified in [RFC9085] and for the MPLS data plane instantiation (SR-
   MPLS) and in [RFC9086] for BGP Egress Peer Engineering (EPE) is specified
   in [RFC9086]. (EPE).  On
   similar lines, introducing the SRv6 related SRv6-related information in BGP-LS
   allows consumer applications that require topological visibility to
   also receive the SRv6 SIDs from nodes across an IGP domain or even
   across Autonomous Systems (AS), (ASes) as required.  This allows
   applications to leverage the SRv6 capabilities for network
   programming.

   The identifying key of each Link-State link-state object, namely a node, link,
   or prefix, is encoded in the Network-Layer Network Layer Reachability Information
   (NLRI)
   (NLRI), and the properties of the object are encoded in the BGP-LS
   Attribute [RFC7752].

   This document describes extensions to BGP-LS to advertise the SRv6
   SIDs and other SRv6 information from all the SRv6 capable SRv6-capable nodes in
   the IGP domain when sourced from link-state routing protocols and
   directly from individual SRv6 capable SRv6-capable nodes (e.g. (e.g., when sourced from
   BGP for EPE).

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  BGP-LS Extensions for SRv6

   BGP-LS [RFC7752] defines the Node, Link, and Prefix Link-State
   Network Layer Reachability Information (NLRI) NLRI
   types and the advertisement of their attributes via BGP.

   When a BGP-LS router advertises topology information that it sources
   from the underlying link-state routing protocol, then it derives the
   corresponding SRv6 information from the SRv6 extensions for IS-IS
   [I-D.ietf-lsr-isis-srv6-extensions]
   [RFC9352] or OSPFv3
   [I-D.ietf-lsr-ospfv3-srv6-extensions], [RFC9513] as applicable.  In practice, this
   derivation comprises a simple copy of the relevant fields from the IS-IS/OSPFv3
   IS-IS or OSPFv3 TLV/sub-TLV into the fields of the corresponding
   BGP-LS BGP-
   LS TLV/sub-TLV.  When a BGP-LS router advertises topology information
   from the BGP routing protocol (e.g., for EPE) or when it advertises SRv6 SIDs
   associated with a node using Direct as the Protocol-ID, then it derives
   the SRv6 information from the local node.  Such information is
   advertised only on behalf of the local router, in contrast to the
   advertisement of information from all nodes of an IGP domain when
   sourced from a link-state routing protocol.

   The SRv6 information pertaining to a node is advertised via the BGP-
   LS Node NLRI and using the BGP-LS Attribute TLVs as follows:

   *  The SRv6 Capabilities capabilities of the node are advertised via the SRv6
      Capabilities TLV (Section 3.1).

   *  Maximum SID Depth (MSD) types introduced for SRv6 are advertised
      (Section 3.2) using the Node MSD TLV specified in [RFC8814] [RFC8814].

   *  Algorithm support for SRv6 is advertised via the SR-Algorithm TLV
      specified in [RFC9085].

   The SRv6 information pertaining to a link is advertised via the BGP-
   LS Link NLRI and using the BGP-LS Attribute TLVs as follows:

   *  The SRv6 SID of the IGP Adjacency SID or the BGP EPE Peer
      Adjacency SID [RFC8402] is advertised via the SRv6 End.X SID TLV
      introduced in this document (Section 4.1).

   *  The SRv6 SID of the IGP Adjacency SID to a non-Designated Router
      (DR) or non-Designated Intermediate-System Intermediate System (DIS) [RFC8402] is
      advertised via the SRv6 LAN End.X SID TLV introduced in this
      document (Section 4.2).

   *  MSD types introduced for SRv6 are advertised (Section 4.3) using
      the Link MSD TLV specified in [RFC8814].

   The SRv6 information pertaining to a prefix is advertised via the
   BGP-LS Prefix NLRI and using the BGP-LS Attribute TLVs as follows:

   *  The SRv6 Locator is advertised via the SRv6 Locator TLV introduced
      in this document (Section 5.1).

   *  The attributes of the SRv6 Locator are advertised via the Prefix
      Attribute Flags TLV specified in [RFC9085].

   The SRv6 SIDs associated with the node are advertised using the BGP-
   LS SRv6 SID NLRI introduced in this document (Section 6).  This
   enables the BGP-LS encoding to scale to cover a potentially large set
   of SRv6 SIDs instantiated on a node with the granularity of
   individual SIDs and without affecting the size and scalability of the
   BGP-LS updates.  Had  If the SRv6 SIDs had been advertised within the BGP-LS BGP-
   LS Link Attribute associated with the existing Node NLRI, the BGP-LS
   update would have grown rather large with the increase in SRv6 SIDs
   on the node and would have also required a large update message to be
   generated for any change, even a change to even a single SRv6 SID.  BGP-LS
   Attribute TLVs for the SRv6 SID NLRI are introduced in this document
   as follows:

   *  The endpoint Endpoint behavior of the SRv6 SID is advertised via the SRv6
      Endpoint Behavior TLV (Section 7.1).

   *  The BGP EPE Peer Node context for a PeerNode SID, SID and the Peer Set
      context for a PeerSet SID [RFC8402] are advertised via the SRv6
      BGP EPE Peer Node PeerNode SID TLV (Section 7.2), 7.2).

   Subsequent sections of this document specify the encoding and usage
   of these extensions.  All the TLVs introduced follow the formats and
   common field definitions provided in [RFC7752].

3.  SRv6 Node Attributes

   The SRv6 attributes of a node are advertised using the BGP-LS
   Attribute TLVs defined in this section and associated with the BGP-LS
   Node NLRI.

3.1.  SRv6 Capabilities TLV

   This BGP-LS Attribute TLV is used to announce the SRv6 capabilities
   of the node along with the BGP-LS Node NLRI and indicates the SRv6
   support by the node.  A single instance of this TLV MUST be included
   in the BGP-LS attribute Attribute for each SRv6 capable SRv6-capable node.  The IS-IS SRv6
   Capabilities sub-TLV [I-D.ietf-lsr-isis-srv6-extensions] [RFC9352] and the OSPFv3 SRv6 Capabilities TLV [I-D.ietf-lsr-ospfv3-srv6-extensions]
   [RFC9513] that map to this BGP-LS TLV are specified with the ability
   to carry optional sub-sub-TLVs/sub-TLVs. sub-sub-TLVs and sub-TLVs.  However, no such
   extensions are currently defined.  Moreover, the SRv6 Capabilities
   TLV defined below is not extensible.  As a result, it is expected
   that any extensions will be introduced as top-level TLVs in the BGP-LS BGP-
   LS Attribute.  The SRv6 Capabilities TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             Flags             |         Reserved              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                   Figure 1: SRv6 Capabilities TLV Format

   Where:

   *

   where:

   Type:  1038

   *  Length : 4.

   *

   Length:  4

   Flags: 2 octet  2-octet field.  The flags are copied from the IS-IS SRv6
      Capabilities sub-TLV (section (Section 2 of
      [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or from the OSPFv3
      SRv6 Capabilities TLV (section (Section 2 of
      [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS IS-
      IS or
      OSPFv3 OSPFv3, respectively.

   *

   Reserved: 2 octet  2-octet field that MUST be set to 0 when originated and
      ignored on receipt.

3.2.  SRv6 Node MSD Types

   The Node MSD TLV [RFC8814] of the BGP-LS Attribute of the Node NLRI
   is also used to advertise the limits and the Segment Routing Header
   (SRH) [RFC8754] operations supported by the SRv6 capable SRv6-capable node.  The
   SRv6 MSD Types types specified in section Section 4 of
   [I-D.ietf-lsr-isis-srv6-extensions] [RFC9352] are also used with
   the BGP-LS Node MSD TLV TLV, as these code points are shared between the
   IS-IS, OSPF OSPF, and BGP-LS protocols.  The description and semantics of
   these new MSD- MSD types for BGP-LS are identical as to those specified in
   [I-D.ietf-lsr-isis-srv6-extensions].
   [RFC9352].

   Each MSD-type MSD type is encoded in the BGP-LS Node MSD TLV as a one-octet
   type followed by a one-octet value as derived from the IS-IS or
   OSPFv3 Node MSD advertisements as specified in [RFC8814].

4.  SRv6 Link Attributes

   SRv6 attributes and SIDs associated with a link or adjacency are
   advertised using the BGP-LS Attribute TLVs defined in this section
   and associated with the BGP-LS Link NLRI.

4.1.  SRv6 End.X SID TLV

   The SRv6 End.X SID TLV is used to advertise the SRv6 SIDs associated
   with an IGP Adjacency SID behavior that correspond to a point-to-
   point or point-to-multipoint link or adjacency of the node running
   the IS-IS or OSPFv3 protocols.  The information advertised via this
   TLV is derived from the IS-IS SRv6 End.X SID sub-TLV (section (Section 8.1 of
   [I-D.ietf-lsr-isis-srv6-extensions])
   [RFC9352]) or the OSPFv3 SRv6 End.X SID sub-TLV (section (Section 9.1 of [I-D.ietf-lsr-ospfv3-srv6-extensions])
   [RFC9513]) in the case of IS-IS or OSPFv3 OSPFv3, respectively.  This TLV
   can also be used to advertise the SRv6 SID corresponding to the
   underlying layer-2 Layer 2 member links for a layer-3 Layer 3 bundle interface as a
   sub-TLV of the L2 Bundle Member Attribute TLV [RFC9085].

   This TLV is also used by BGP-LS to advertise the BGP EPE Peer
   Adjacency SID for SRv6 on the same lines as specified for SR-MPLS in
   [RFC9086].  The SRv6 SID for the BGP Peer Adjacency using End.X
   behaviors (viz. End.X, End.X with PSP, End.X with USP, and End.X with
   PSP & USP) [RFC8986] indicates the cross-connect to a specific
   layer-3 Layer
   3 link to the specific BGP session peer (neighbor).

   More than one instance of this TLV (one for each SRv6 End.X SID) can
   be included in the BGP-LS
   Attribute; one for each SRv6 End.X SID. Attribute.

   The TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |        Endpoint Behavior      |      Flags    |   Algorithm   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Weight    |   Reserved    |  SID (16 octets) ...          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)             | Sub-TLVs (variable) . . .
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 2: SRv6 End.X SID TLV Format

   Where:

   where:

   Type:  1106

   Length:  variable

   Endpoint Behavior: 2 octet  2-octet field.  The Endpoint Behavior behavior code point
      for this SRv6 SID as defined in section Section 10.2 of [RFC8986].

   Flags:  1 octet of flags.  The flags are copied from the IS-IS SRv6
      End.X SID sub-TLV (section (Section 8.1 of
      [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3 SRv6
      End.X SID sub-TLV (section (Section 9.1 of [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS
      or OSPFv3 OSPFv3, respectively.  In the case of the BGP EPE Peer
      Adjacency SID, the flags are as defined in Section 7.2.

   Algorithm: 1 octet  1-octet field.  Algorithm associated with the SID.

   Weight: 1 octet  1-octet field.  The value represents the weight of the SID
      for the purpose of load balancing.  The use of the weight is
      defined in [RFC8402].

   Reserved: 1 octet  1-octet field that MUST be set to 0 when originated and
      ignored on receipt.

   SID: 16 octet  16-octet field.  This field encodes the advertised SRv6 SID as 128 bit
      a 128-bit value.

      Sub-TLVs :

   Sub-TLVs:  Used to advertise sub-TLVs that provide additional
      attributes for the specific SRv6 SID.  This document defines one
      in Section 8.

4.2.  SRv6 LAN End.X SID TLV

   For a LAN interface, an IGP node ordinarily announces only its
   adjacency to the IS-IS pseudo-node pseudonode (or the equivalent OSPF DR).  The
   information advertised via this TLV is derived from the IS-IS SRv6
   LAN End.X SID sub-TLV (section (Section 8.2 of
   [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3 SRv6
   LAN End.X SID sub-TLV (section (Section 9.2 of [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS
   or OSPFv3 OSPFv3, respectively.  The SRv6 LAN End.X SID TLV allows a node to
   announce the SRv6 SID corresponding to its adjacencies to all other
   (i.e., non-DIS or non-DR) nodes attached to the LAN in a single
   instance of the BGP-LS Link NLRI.  Without this TLV, multiple BGP-LS
   Link NLRIs would need to be originated, one for each neighbor, to
   advertise the SRv6 End.X SID TLVs for those non-
   DIS/non-DR non-DIS/non-DR neighbors.
   The SRv6 SID for these IGP adjacencies using the End.X behaviors
   (viz. End.X, End.X with PSP, End.X with USP, and End.X with PSP &
   USP) [RFC8986] are advertised using the SRv6 LAN End.X SID TLV.

   More than one instance of this TLV (one for each SRv6 LAN End.X SID)
   can be included in the BGP-LS
   Attribute; one for each SRv6 LAN End.X SID. Attribute.

   The BGP-LS IS-IS SRv6 LAN End.X SID and BGP-LS OSPFv3 SRv6 LAN End.X
   SID TLVs have the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Endpoint Behavior       |      Flags    |   Algorithm   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Weight    |   Reserved    |   Neighbor ID -               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               |
   | IS-IS System-ID (6 octets) or OSPFv3 Router-ID (4 octets)     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (16 octets) ...                                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Sub-TLVs (variable) . . .
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                  Figure 3: SRv6 LAN End.X SID TLV Format

   Where:

   *

   where:

   Type:  1107 in case of for IS-IS and 1108 in case of for OSPFv3

   *

   Length:  variable

   *

   Endpoint Behavior: 2 octet  2-octet field.  The Endpoint Behavior behavior code point
      for this SRv6 SID as defined in section Section 10.2 of [RFC8986].

   *

   Flags:  1 octet of flags.  The flags are copied from the IS-IS SRv6
      LAN End.X SID sub-TLV (section (Section 8.2 of
      [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3
      SRv6 LAN End.X SID sub-TLV (section (Section 9.2 of [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case
      of IS-IS or OSPFv3 OSPFv3, respectively.

   *

   Algorithm: 1 octet  1-octet field.  Algorithm associated with the SID.

   *

   Weight: 1 octet  1-octet field.  The value represents the weight of the SID
      for the purpose of load balancing.

   *

   Reserved: 1 octet  1-octet field that MUST be set to 0 when originated and
      ignored on receipt.

   *

   Neighbor ID : ID:  6 octets of Neighbor System-ID in the IS-IS SRv6 LAN
      End.X SID TLV or 4 octets of Neighbor Router-id Router-ID in the OSPFv3 SRv6
      LAN End.X SID TLV.

   *

   SID: 16 octet  16-octet field.  This field encodes the advertised SRv6 SID as 128 bit
      a 128-bit value.

   *  Sub-TLVs :

   Sub-TLVs:  Used to advertise sub-TLVs that provide additional
      attributes for the specific SRv6 SID.  This document defines one
      in Section 8.

4.3.  SRv6 Link MSD Types

   The Link MSD TLV [RFC8814] of the BGP-LS Attribute of the Link NLRI
   is also used to advertise the limits and the SRH operations supported
   on the specific link by the SRv6 capable SRv6-capable node.  The SRv6 MSD Types types
   specified in section Section 4 of[I-D.ietf-lsr-isis-srv6-extensions] of [RFC9352] are also used with the BGP-LS
   Link MSD TLV TLV, as these code points are shared between the IS-IS,
   OSPF, and BGP-LS protocols.  The description and semantics of these
   new MSD types for BGP-LS are identical as specified in [I-D.ietf-lsr-isis-srv6-extensions]. [RFC9352].

   Each MSD-type MSD type is encoded in the BGP-LS Link MSD TLV as a one-octet
   type followed by a one-octet value as derived from the IS-IS or
   OSPFv3 Link MSD advertisements as specified in [RFC8814].

5.  SRv6 Prefix Attributes

   SRv6 attributes with an IPv6 prefix are advertised using the BGP-LS
   Attribute TLVs defined in this section and associated with the BGP-LS
   Prefix NLRI.

5.1.  SRv6 Locator TLV

   As specified in [RFC8986], an SRv6 SID comprises Locator, Function locator, function,
   and Argument argument parts.

   A node is provisioned with one or more Locators locators supported by that
   node.  Locators are covering prefixes for the set of SIDs provisioned
   on that node.  Each Locator locator is advertised as a BGP-LS Prefix NLRI
   object along with the SRv6 Locator TLV in its BGP-LS Attribute.

   The information advertised via this TLV is derived from the IS-IS
   SRv6 Locator TLV (section (Section 7.1 of [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3 SRv6
   Locator TLV (section (Section 7.1 of
   [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS or OSPFv3
   OSPFv3, respectively.

   The IPv6 Prefix matching the Locator locator may be also be advertised as prefix
   reachability by the underlying routing protocol.  In this case, the
   Prefix NLRI would be also be associated with the Prefix Metric TLV
   [RFC7752] that carries the routing metric for this prefix.  A Prefix
   NLRI,
   NLRI that has been advertised with a SRv6 Locator TLV, TLV is also
   considered a normal routing prefix (i.e., prefix reachability) only
   when there is also an IGP metric Metric TLV (TLV 1095) associated it.
   Otherwise, it is considered only as considered an SRv6 Locator advertisement.

   The SRv6 Locator TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Flags    |   Algorithm   |           Reserved            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                            Metric                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Sub-TLVs (variable) . . .
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 4: SRv6 Locator TLV Format

   Where:

   where:

   Type:  1162

   Length:  variable

   Flags:  1 octet of flags.  The flags are copied from the IS-IS SRv6
      Locator TLV (section (Section 7.1 of [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3 SRv6 Locator
      TLV (section (Section 7.1 of
      [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS or
      OSPFv3 OSPFv3,
      respectively.

   Algorithm: 1 octet  1-octet field.  Algorithm associated with the SID.

   Reserved: 2 octet  2-octet field.  The value MUST be set to 0 when originated
      and ignored on receipt.

   Metric: 4 octet  4-octet field.  The value of the metric for the Locator locator
      copied from the IS-IS SRv6 Locator TLV (section (Section 7.1 of
      [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352])
      or the OSPFv3 SRv6 Locator TLV (section (Section 7.1 of [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the
      case of IS-IS or OSPFv3 OSPFv3, respectively.

      Sub-TLVs :

   Sub-TLVs:  Used to advertise sub-TLVs that provide additional
      attributes for the given SRv6 Locator.  Currently, none are
      defined.

6.  SRv6 SID NLRI

   The "Link-State NLRI" Link-State NLRI defined in [RFC7752] is extended to carry the
   SRv6 SID information.

   A

   This document defines the following new "Link-State Link-State NLRI Type" is defined type for SRv6
   SID information as
   follows:

   *  Link-State NLRI Type: information: SRv6 SID NLRI (value (type 6).

   The SRv6 SIDs associated with the node are advertised using the BGP-
   LS SRv6 SID NLRI.

   The format of this

   This new NLRI type is as shown in has the following figure: format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+
   |  Protocol-ID  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                        Identifier                             |
   |                        (8 octets)                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Local Node Descriptors (variable)              //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               SRv6 SID Descriptors (variable)                //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 5: SRv6 SID NLRI Format

   Where:

   *

   where:

   Protocol-ID:  1-octet field that specifies the information source
      protocol [RFC7752].

   *

   Identifier: 8 octet  8-octet value as defined in [RFC7752].

   *

   Local Node Descriptors TLV: set  Set of Node Descriptor TLVs for the
      local node, node as defined in [RFC7752] for IGPs, direct, the Direct Protocol-
      ID, and static the Static configuration Protocol-ID or as defined in
      [RFC9086] for BGP protocol.

   * BGP.

   SRv6 SID Descriptors: set  Set of SRv6 SID Descriptor TLVs.  This field
      MUST contain a single SRv6 SID Information TLV (Section 6.1) and
      MAY contain the Multi-Topology Identifier TLV [RFC7752].

   New TLVs for advertisement within the BGP-LS Attribute [RFC7752] are
   defined in Section 7 to carry the attributes of an SRv6 SID.

6.1.  SRv6 SID Information TLV

   An SRv6 SID that is associated with the node and advertised using the
   SRv6 SID NLRI is encoded using the SRv6 SID Information TLV.

   When advertising the SRv6 SIDs from the IGPs, the SID information is
   derived from the IS-IS SRv6 End SID sub-TLV (section (Section 7.2 of
   [I-D.ietf-lsr-isis-srv6-extensions])
   [RFC9352]) or the OSPFv3 SRv6 End SID sub-
   TLV (section sub-TLV (Section 8 of [I-D.ietf-lsr-ospfv3-srv6-extensions])
   [RFC9513]) in the case of IS-IS or OSPFv3 OSPFv3, respectively.

   The TLV carries the SRv6 SIDs corresponding to the BGP PeerNode and
   PeerSet SID SIDs [RFC8402] when SRv6 BGP EPE functionality is enabled in
   BGP.

   The TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (16 octets) ...                                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    SID (cont ...)                                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                 Figure 6: SRv6 SID Information TLV Format

   Where:

   where:

   Type:  518

   Length: 16.

      SID:  16 octet

   SID:  16-octet field.  This field encodes the advertised SRv6 SID as 128 bit
      a 128-bit value.

7.  SRv6 SID Attributes

   This section specifies the TLVs to be carried in the BGP Link State
   Attribute associated with the BGP-LS SRv6 SID NLRI.

7.1.  SRv6 Endpoint Behavior TLV

   Each SRv6 SID instantiated on an SRv6 capable SRv6-capable node has specific
   instructions (called behavior) "behavior") bound to it.  [RFC8986] describes
   how behaviors are bound to a SID and also defines the initial set of
   well-known behaviors.

   The SRv6 Endpoint Behavior TLV is a mandatory TLV that MUST be
   included in the BGP-LS Attribute associated with the BGP-LS SRv6 SID
   NLRI.

   When advertising the SRv6 SIDs from the IGPs, the Endpoint behavior,
   Flags, and Algorithm are derived from the IS-IS SRv6 End SID sub-TLV
   (section
   (Section 7.2 of [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3 SRv6 End SID sub-TLV (section
   (Section 8 of
   [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS or OSPFv3 OSPFv3,
   respectively.

   When advertising the SRv6 SIDs corresponding to the BGP EPE
   functionality, the Endpoint Behavior behavior corresponds to End.X and similar
   behaviors.  When advertising the SRv6 SIDs that are locally
   instantiated on the node using Direct as the Protoocl-ID, The Protocol-ID, the
   Endpoint Behavior behavior corresponds to any SRv6 Endpoint Behavior behavior
   associated with the node.  Flags are currently not defined.  The
   algorithm value MUST be 0 unless an algorithm is associated locally
   with the SRv6 Locator from which the SID is allocated.

   The TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |        Endpoint Behavior      |      Flags    |   Algorithm   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 7: SRv6 Endpoint Behavior TLV

   Where:

   where:

   Type:  1250

   Length: 4.  4

   Endpoint Behavior: 2 octet  2-octet field.  The Endpoint Behavior behavior code point
      for this SRv6 SID.  Support values  Values are those from the "SRv6 Endpoint Behaviors"
      IANA registry (as established via section (Section 10.2 of [RFC8986]).

   Flags:  1 octet of flags.  The flags map to the IS-IS or OSPFv3
      encodings when advertising SRv6 SIDs corresponding to IGPs.  For  No
      flags are currently defined for SRv6 SIDs corresponding to BGP EPE and when advertising
      or for advertisement of a SRv6 SID using Direct Protocol-ID, none are defined currently and they as the Protocol-
      ID.  Undefined flags MUST be set to 0 when originated originating and ignored
      on receipt.

   Algorithm: 1 octet  1-octet field.  Algorithm associated with the SID.

7.2.  SRv6 BGP Peer Node PeerNode SID TLV

   The BGP PeerNode SID and PeerSet SID SIDs for SR-MPLS are specified in
   [RFC9086].  Similar Peer Node and Peer Set functionality can be
   realized with SRv6 using SIDs with END.X behavior.  Refer to
   Appendix A for some differences between the signaling of these SIDs
   in SR-MPLS and SRv6.  The SRv6 BGP Peer Node PeerNode SID TLV is a mandatory
   TLV for use in the BGP-LS Attribute for an SRv6 SID NLRI advertised
   by BGP for the EPE functionality.  This TLV MUST be included along
   with SRv6 SIDs that are associated with the BGP PeerNode or PeerSet
   functionality.

   The TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Flags    |     Weight    |          Reserved             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Peer AS Number                           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Peer BGP Identifier                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                 Figure 8: SRv6 BGP Peer Node PeerNode SID TLV Format

   Where:

   *

   where:

   Type:  1251

   *

   Length:  12
   *

   Flags:  1 octet of flags with the following definition: definitions:

       0 1 2 3 4 5 6 7
      +-+-+-+-+-+-+-+-+
      |B|S|P|         |
      +-+-+-+-+-+-+-+-+

                   Figure 9: SRv6 BGP EPE SID Flags Format

      -

      B-Flag:  Backup Flag.  If set, the SID is eligible to be protected
         using fast reroute Fast Reroute (FRR).  The computation of the backup
         forwarding path and its association with the forwarding entry
         for the Peer BGP Identifier is are implementation specific.

      -

      S-Flag:  Set Flag.  When set, the S-Flag indicates that the SID
         refers to a set of BGP peering sessions (i.e., BGP Peer Set SID
         functionality) and therefore MAY be assigned to one or more
         End.X SIDs associated with BGP peer peering sessions.

      -

      P-Flag:  Persistent Flag: Flag.  When set, the P-Flag indicates that the
         SID is persistently allocated, i.e., the value remains
         consistent across router restart and/or session flap.

      -

      Other bits are reserved for future use and MUST be set to 0
      when originated and ignored on receipt.  The flags defined
      above are also used with the SRv6 End.X SID TLV when
      advertising the SRv6 BGP Peer Adjacency SID (Section 4.1).

   *

   Weight: 1 octet  1-octet field.  The value represents the weight of the SID
      for the purpose of load balancing.  The use of the weight is
      defined in [RFC8402].

   *

   Reserved: 2 octet  2-octet field.  The value MUST be set to 0 when originated
      and ignored on receipt.

   *

   Peer AS Number : Number:  4 octets of the BGP AS number of the peer router.

   *

   Peer BGP Identifier : Identifier:  4 octets of the BGP Identifier (BGP Router-
      ID) Router-ID)
      of the peer router.

   For an SRv6 BGP EPE Peer Node PeerNode SID, one instance of this TLV is
   associated with the SRv6 SID.  For an SRv6 BGP EPE Peer Set PeerSet SID,
   multiple instances of this TLV (one for each peer in the “peer set”) "peer set")
   are associated with the SRv6 SID and the S-Flag is SET. set.

8.  SRv6 SID Structure TLV

   The SRv6 SID Structure TLV is used to advertise the length of each
   individual part of the SRv6 SID as defined in [RFC8986].  It is an
   optional TLV for use in the BGP-LS Attribute for an SRv6 SID NLRI and
   as a sub-TLV of the SRv6 End.X SID, IS-IS SRv6 LAN End.X SID, and
   OSPFv3 SRv6 LAN End.X SID TLVs.

   When advertising SRv6 SIDs from the IGPs, the SRv6 SID Structure
   information is derived from the IS-IS SRv6 SID Structure sub-sub-TLV
   (section
   (Section 9 of [I-D.ietf-lsr-isis-srv6-extensions]) [RFC9352]) or the OSPFv3 SRv6 SID Structure sub-TLV (section
   (Section 10 of
   [I-D.ietf-lsr-ospfv3-srv6-extensions]) [RFC9513]) in the case of IS-IS or OSPFv3 OSPFv3,
   respectively.

   When advertising the SRv6 SIDs corresponding to the BGP EPE
   functionality or for advertising SRv6 SIDs using Direct as the
   Protocol-ID, the SRv6 SID Structure information is derived from the
   locally provisioned SRv6 SID.

   The TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    LB Length  |  LN Length    | Fun. Length   |  Arg. Length  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 10: SRv6 SID Structure TLV

   Where:

   where:

   Type:  1252

   Length:  4

   LB Length: 1 octet  1-octet field.  SRv6 SID Locator Block length in bits.

   LN Length: 1 octet  1-octet field.  SRv6 SID Locator Node length in bits.

   Fun. Length: 1 octet  1-octet field.  SRv6 SID Function length in bits.

   Arg. Length: 1 octet  1-octet field.  SRv6 SID Argument length in bits.

   The sum of the LB Length, LN Length, Func. Fun. Length, and Arg. Length
   MUST be less than or equal to 128.

9.  IANA Considerations

   This document requests assigning

   Per this document, IANA has allocated code points from in the IANA "Border
   Gateway Protocol - Link State (BGP-LS) Parameters" registry group group, as
   described in the subsections below.

9.1.  BGP-LS NLRI-Types

   The NLRI Types

   IANA has assigned the following code points have been assigned by IANA from in the
   registry called "BGP-LS NLRI-Types":

    +------+----------------------------+---------------+ NLRI
   Types" registry:

                   +======+===============+===========+
                   | Type | NLRI Type     | Reference |
    +------+----------------------------+---------------+
                   +======+===============+===========+
                   | 6    | SRv6 SID NLRI | this document RFC 9514  |
    +------+----------------------------+---------------+

                  Figure 11: SRv6 SID
                   +------+---------------+-----------+

                     Table 1: Addition to BGP-LS NLRI Type Code Point
                              Types Registry

9.2.  BGP-LS NLRI and Attribute TLVs

   The

   IANA has assigned the following TLV code points have been assigned by IANA from in the
   registry called "BGP-LS Node Descriptor, Link Descriptor, Prefix
   Descriptor, NLRI
   and Attribute TLVs":

   +----------+----------------------------------------+---------------+ TLVs" registry:

        +================+===========================+===========+
        | TLV Code |             Description                | Value defined |
   | Point | Description               |       in Reference |
   +----------+----------------------------------------+---------------+
        +================+===========================+===========+
        | 518            | SRv6 SID Information      | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1038           | SRv6 Capabilities         | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1106           | SRv6 End.X SID            | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1107           | IS-IS SRv6 LAN End.X SID  | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1108           | OSPFv3 SRv6 LAN End.X SID | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1162           | SRv6 Locator              | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1250           | SRv6 Endpoint Behavior    | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1251           | SRv6 BGP Peer Node PeerNode SID     | this document RFC 9514  |
        +----------------+---------------------------+-----------+
        | 1252           | SRv6 SID Structure        | this document RFC 9514  |
   +----------+----------------------------------------+---------------+

              Figure 12: SRv6
        +----------------+---------------------------+-----------+

           Table 2: Additions to BGP-LS NLRI and Attribute TLV Code Points TLVs
                                 Registry

9.3.  SRv6 BGP EPE SID Flags

   This document requests the creation of

   Per this document, IANA has created a new registry called "SRv6 BGP
   EPE SID Flags" under the "Border Gateway Protocol - Link State
   (BGP-LS) (BGP-
   LS) Parameters" registry group.  The allocation policy of this
   registry is "Standards Action" according to [RFC8126].

   The following flags initial contents of the registry are defined: as follows:

              +=====+==========================+===========+
              | Bit | Description              | Reference
            --------------------------------------------------- |
              +=====+==========================+===========+
              | 0   | Backup Flag (B-Flag)        This document     | RFC 9514  |
              +-----+--------------------------+-----------+
              | 1   | Set Flag (S-Flag)           This document        | RFC 9514  |
              +-----+--------------------------+-----------+
              | 2   | Persistent Flag (P-Flag)    This document | RFC 9514  |
              +-----+--------------------------+-----------+
              | 3-7 | Unassigned

                     Figure 13:               |           |
              +-----+--------------------------+-----------+

               Table 3: New SRv6 BGP EPE SID Flags Registry

10.  Manageability Considerations

   This section is structured as recommended in [RFC5706].

   The new protocol extensions introduced in this document augment the
   existing IGP topology information that is distributed via [RFC7752].
   Procedures and protocol extensions defined in this document do not
   affect the BGP protocol operations and management other than as
   discussed in the Manageability Considerations section Section 6 (Manageability Considerations) of [RFC7752].
   Specifically, the malformed attribute tests for syntactic checks in
   the Fault Management section
   Section 6.2.2 (Fault Management) of [RFC7752] now encompass the new BGP-
   LS
   BGP-LS extensions defined in this document.  The semantic or content
   checking for the TLVs specified in this document and their
   association with the BGP-LS NLRI types or their BGP-LS Attribute is are
   left to the consumer of the BGP-LS information (e.g., an application
   or a controller) and not the BGP protocol. BGP.

   The SR information introduced in BGP-LS by this specification may be
   used by BGP-LS consumer applications like an SR path computation
   engine Path Computation
   Engine (PCE) to learn the SRv6 capabilities of the nodes in the
   topology and the mapping of SRv6 segments to those nodes.  This can
   enable the SR PCE to perform path computations based on SR for
   traffic engineering use-cases
   traffic-engineering use cases and to steer traffic on paths different
   from the underlying IGP based IGP-based distributed best path computation.
   Errors in the encoding or decoding of the SRv6 information may result
   in the unavailability of such information to the SR PCE or incorrect
   information being made available to it.  This may result in the SR
   PCE not being able to perform the desired SR-based optimization
   functionality or to perform performing it in an unexpected or inconsistent
   manner.  The handling of such errors by applications like SR PCE may
   be implementation-specific implementation specific and out of the scope of this document.

   The manageability considerations related to BGP EPE functionality are
   discussed in [RFC9086] in the context of SR-MPLS and SR-MPLS; they also apply to
   this document in the context of SRv6.

   The extensions, extensions specified in this document, document do not introduce any new
   configuration or monitoring aspects in BGP or BGP-LS other than as
   discussed in [RFC7752].  The manageability aspects of the underlying
   SRv6 features are covered by [I-D.ietf-spring-srv6-yang]. [SRV6-YANG].

11.  Security Considerations

   The new protocol extensions introduced in this document augment the
   existing IGP topology information that is distributed via [RFC7752].
   The advertisement of the SRv6 link-state information defined in this
   document presents a similar risk as associated with the existing set
   of
   link-state information as described in [RFC7752].  The Security
   Considerations section  Section 8
   (Security Considerations) of [RFC7752] also applies to these
   extensions.  The procedures and new TLVs defined in this document, by
   themselves, do not affect the BGP-LS security model discussed in
   [RFC7752].

   The extensions introduced in this document are used to propagate IGP IGP-
   defined information ([I-D.ietf-lsr-isis-srv6-extensions] and
   [I-D.ietf-lsr-ospfv3-srv6-extensions]). [RFC9352] [RFC9513].  These extensions represent
   the advertisement of SRv6 information associated with the IGP node,
   link, and prefix.  The IGP instances originating these TLVs are
   assumed to support all the required security and authentication
   mechanisms (as described in [I-D.ietf-lsr-isis-srv6-extensions] [RFC9352] and
   [I-D.ietf-lsr-ospfv3-srv6-extensions]). [RFC9513]).

   The security considerations related to BGP EPE functionality are
   discussed in [RFC9086] in the context of SR-MPLS SR-MPLS, and they also apply
   to this document in the context of SRv6.

   BGP-LS SRv6 extensions enable traffic engineering use-cases traffic-engineering use cases within
   the Segment Routing SR domain.  SR operates within a trusted domain
   [RFC8402] [RFC8402], and
   its security considerations also apply to BGP-LS sessions when
   carrying SR information.  The SR traffic engineering traffic-engineering policies using
   the SIDs advertised via BGP-LS are expected to be used entirely
   within this trusted SR domain (e.g., between multiple AS or IGP
   domains within a single provider network).  Therefore, precaution is
   necessary to ensure that the link-state information (including SRv6
   information) advertised via BGP-LS sessions is securely limited to
   consumers within this trusted SR domain.  BGP peering sessions for
   address-families
   address families other than Link-State Link State may be set up to routers
   outside the SR domain.  The isolation of BGP-LS peering sessions is
   RECOMMENDED to ensure that BGP-LS topology information (including the
   newly added SR information) is not advertised to an external BGP
   peering session outside the SR domain.

14.

12.  References

14.1.

12.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC7752]  Gredler, H., Ed., Medved, J., Previdi, S., Farrel, A., and
              S. Ray, "North-Bound Distribution of Link-State and
              Traffic Engineering (TE) Information Using BGP", RFC 7752,
              DOI 10.17487/RFC7752, March 2016,
              <https://www.rfc-editor.org/info/rfc7752>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

   [RFC8814]  Tantsura, J., Chunduri, U., Talaulikar, K., Mirsky, G.,
              and N. Triantafillis, "Signaling Maximum SID Depth (MSD)
              Using the Border Gateway Protocol - Link State", RFC 8814,
              DOI 10.17487/RFC8814, August 2020,
              <https://www.rfc-editor.org/info/rfc8814>.

   [RFC8986]  Filsfils, C., Ed., Camarillo, P., Ed., Leddy, J., Voyer,
              D., Matsushima, S., and Z. Li, "Segment Routing over IPv6
              (SRv6) Network Programming", RFC 8986,
              DOI 10.17487/RFC8986, February 2021,
              <https://www.rfc-editor.org/info/rfc8986>.

   [RFC9085]  Previdi, S., Talaulikar, K., Ed., Filsfils, C., Gredler,
              H., and M. Chen, "Border Gateway Protocol - Link State
              (BGP-LS) Extensions for Segment Routing", RFC 9085,
              DOI 10.17487/RFC9085, August 2021,
              <https://www.rfc-editor.org/info/rfc9085>.

   [RFC9086]  Previdi, S., Talaulikar, K., Ed., Filsfils, C., Patel, K.,
              Ray, S., and J. Dong, "Border Gateway Protocol - Link
              State (BGP-LS) Extensions for Segment Routing BGP Egress
              Peer Engineering", RFC 9086, DOI 10.17487/RFC9086, August
              2021, <https://www.rfc-editor.org/info/rfc9086>.

   [I-D.ietf-lsr-isis-srv6-extensions]

   [RFC9352]  Psenak, P., Ed., Filsfils, C., Bashandy, A., Decraene, B.,
              and Z. Hu, "IS-IS Extensions to Support Segment Routing
              over the IPv6 Dataplane", Work in Progress, Internet-Draft, draft-
              ietf-lsr-isis-srv6-extensions-19, 14 November 2022,
              <https://www.ietf.org/archive/id/draft-ietf-lsr-isis-srv6-
              extensions-19.txt>.

   [I-D.ietf-lsr-ospfv3-srv6-extensions] Data Plane", RFC 9352, DOI 10.17487/RFC9352,
              February 2023, <https://www.rfc-editor.org/info/rfc9352>.

   [RFC9513]  Li, Z., Hu, Z., Talaulikar, K., Ed., and P. Psenak,
              "OSPFv3 Extensions for SRv6", Work in Progress, Internet-Draft,
              draft-ietf-lsr-ospfv3-srv6-extensions-09, 14 January Segment Routing over IPv6 (SRv6)",
              RFC 9513, DOI 10.17487/RFC9513, November 2023,
              <https://www.ietf.org/archive/id/draft-ietf-lsr-
              ospfv3-srv6-extensions-09.txt>.

14.2.
              <https://www.rfc-editor.org/info/rfc9513>.

12.2.  Informative References

   [RFC5706]  Harrington, D., "Guidelines for Considering Operations and
              Management of New Protocols and Protocol Extensions",
              RFC 5706, DOI 10.17487/RFC5706, November 2009,
              <https://www.rfc-editor.org/info/rfc5706>.

   [RFC8754]  Filsfils, C., Ed., Dukes, D., Ed., Previdi, S., Leddy, J.,
              Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header
              (SRH)", RFC 8754, DOI 10.17487/RFC8754, March 2020,
              <https://www.rfc-editor.org/info/rfc8754>.

   [I-D.ietf-spring-srv6-yang]

   [SRV6-YANG]
              Raza, S., Agarwal, S., Liu, X., Hu, Z., Hussain, I., Shah,
              H. C., Voyer, D., Matsushima, S., Horiba, K.,
              Rajamanickam, J., and A. Abdelsalam, "YANG Data Model for
              SRv6 Base and Static", Work in Progress, Internet-Draft,
              draft-ietf-spring-srv6-yang-02, 23 September 2022,
              <https://www.ietf.org/archive/id/draft-ietf-spring-srv6-
              yang-02.txt>.
              <https://datatracker.ietf.org/doc/html/draft-ietf-spring-
              srv6-yang-02>.

Appendix A.  Differences with BGP-EPE for SR-MPLS

   The signaling of SRv6 SIDs corresponding to BGP-EPE functionality as
   defined in this document differ differs from the signaling of SR-MPLS BGP-EPE BGP-
   EPE SIDs as specified in [RFC9086].  This section provides a high-level high-
   level overview of the same.

   There is no difference in the advertisement of the BGP Peer Adjacency
   SID in both SR-MPLS and SRv6 SRv6, and it is advertised as an attribute of
   the Link NLRI NLRI, which identifies a specific Layer 3 interface on the
   BGP Speaker.  The difference is in the advertisement of the BGP Peer
   Node
   PeerNode and Peer Set PeerSet SIDs.

   In the case of SR-MPLS, an additional Link NLRI is required to be
   advertised corresponding to each BGP Peering peering session on the node.
   Note that, that this is not the same Link NLRI associated with the actual
   layer
   Layer 3 interface even when the peering is set up using the interface
   IP addresses.  These BGP-LS Link NLRIs are not really links in the
   conventional link-state routing data model but instead identify BGP
   peering sessions.  The BGP Peer Node PeerNode and/or Peer Set PeerSet SIDs associated
   with that peering session are advertised as attributes associated
   with this peering Link NLRI.  In the case of SRv6, each BGP Peer Node PeerNode
   or Peer Set PeerSet SID is considered to be associated with the BGP Speaker
   node
   Node and is advertised using the BGP-LS SRv6 SID NLRI NLRI, while the
   peering session information is advertised as attributes associated
   with it.

   The advertisement of the BGP Peer Set PeerSet SID for SR-MPLS is done by
   including that SID as an attribute in all the Link NLRIs
   corresponding to the peering sessions that are part of the "set".
   The advertisement of the BGP Peer Set PeerSet SID for SRv6 is advertised using
   a single SRv6 SID NLRI NLRI, and all the peers associated with that "set"
   are indicated as attributes associated with the NLRI.

Acknowledgements

   The authors would like to thank Peter Psenak, Arun Babu, Pablo
   Camarillo, Francois Clad, Peng Shaofu, Cheng Li, Dhruv Dhody, Tom
   Petch, and Dan Romascanu for their review of this document and their
   comments.  The authors would also like to thank Susan Hares for her
   shepherd review and Adrian Farrel for his detailed Routing Area
   Directorate review.

Contributors

   James Uttaro
   AT&T
   USA
   United States of America
   Email: ju1738@att.com

   Hani Elmalky
   Ericsson
   USA
   United States of America
   Email: hani.elmalky@gmail.com

   Arjun Sreekantiah
   Individual
   USA
   United States of America
   Email: arjunhrs@gmail.com

   Les Ginsberg
   Cisco Systems
   USA
   United States of America
   Email: ginsberg@cisco.com

   Shunwan Zhuang
   Huawei
   China
   Email: zhuangshunwan@huawei.com

Authors' Addresses

   Gaurav Dawra
   LinkedIn
   United States of America
   Email: gdawra.ietf@gmail.com

   Clarence Filsfils
   Cisco Systems
   Belgium
   Email: cfilsfil@cisco.com

   Ketan Talaulikar (editor)
   Cisco Systems
   India
   Email: ketant.ietf@gmail.com

   Mach

   Mach(Guoyi) Chen
   Huawei
   China
   Email: mach.chen@huawei.com

   Daniel Bernier
   Bell Canada
   Canada
   Email: daniel.bernier@bell.ca

   Bruno Decraene
   Orange
   France
   Email: bruno.decraene@orange.com