Network Working Group E. Beili Internet-Draft Actelis Networks Intended status: Standards Track M. Morgenstern Expires: January 17, 2013 ECI Telecom Jul 16, 2012 xDSL multi-pair bonding (G.Bond) MIB draft-ietf-adslmib-gbond-mib-11.txt Abstract This document defines Management Information Base (MIB) module for use with network management protocols in TCP/IP-based internets. This document defines an extension to the Interfaces Group MIB with a set of common objects for managing multi-pair bonded Digital Subscriber Line (xDSL) interfaces, defined in ITU-T recommendations G.998.1, G.998.2 and G.998.3. The textual conventions defining the bonding schemes are contained in a separate Internet Assigned Number Authority (IANA) maintained MIB module. The MIB modules specific to each bonding technology are defined in G9981-MIB, G9982-MIB and G9983-MIB respectively. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on January 17, 2013. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of Beili & Morgenstern Expires January 17, 2013 [Page 1] Internet-Draft G.Bond MIB Jul 2012 publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. The Internet-Standard Management Framework . . . . . . . . . . 4 3. The DSL Forum Management Framework for xDSL Bonding . . . . . 4 4. Relationship to Other MIB modules . . . . . . . . . . . . . . 4 4.1. Relationship to Interfaces Group MIB module . . . . . . . 5 4.1.1. Layering Model . . . . . . . . . . . . . . . . . . . . 5 4.1.2. xDSL Bonding . . . . . . . . . . . . . . . . . . . . . 7 4.1.3. Discovery Operation . . . . . . . . . . . . . . . . . 7 4.1.4. G.Bond ports initialization . . . . . . . . . . . . . 10 4.1.5. Usage of ifTable . . . . . . . . . . . . . . . . . . . 10 4.2. Relationship to G.Bond ATM, ETH and TDIM MIB modules . . . 11 4.3. Relationship to xDSL MIB modules . . . . . . . . . . . . . 12 4.4. Addition of new bonding schemes . . . . . . . . . . . . . 12 5. MIB Structure . . . . . . . . . . . . . . . . . . . . . . . . 12 5.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.2. Performance Monitoring . . . . . . . . . . . . . . . . . . 13 5.3. Mapping of DSL Forum TR-159 Managed Objects . . . . . . . 13 6. xDSL Multi-pair Bonding MIB Definitions . . . . . . . . . . . 17 7. IANA-maintained G.Bond TC Definitions . . . . . . . . . . . . 62 8. Security Considerations . . . . . . . . . . . . . . . . . . . 64 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 66 10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 66 11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 67 11.1. Normative References . . . . . . . . . . . . . . . . . . . 67 11.2. Informative References . . . . . . . . . . . . . . . . . . 68 Beili & Morgenstern Expires January 17, 2013 [Page 2] Internet-Draft G.Bond MIB Jul 2012 1. Introduction The xDSL Multi-Pair Bonding, allows a service provider to provide high bandwidth services to business and residential customers over multiple xDSL lines, with greater speed and resiliency, than the service over a single xDSL line, bridging the gap between xDSL and fiber-based transport. Currently there are three xDSL Multi-Pair Bonding schemes, also known under collective name G.Bond: o The ATM-Based Multi-Pair Bonding, specified in ITU-T G.998.1 recommendation [G.998.1], which defines a method for bonding (or aggregating) of multiple xDSL lines (or individual bearer channels in multiple xDSL lines) into a single bi-directional logical link carrying an ATM stream. This specification can be viewed as an evolution of the legacy Inverse Multiplexing over ATM (IMA) technology [af-phy-0086], applied to xDSL with variable rates on each line/bearer channel. o The Ethernet-Based Multi-Pair Bonding, specified in ITU-T G.998.2 recommendation [G.998.2], which defines a method for bonding (or aggregating) of multiple xDSL lines (or individual bearer channels in multiple xDSL lines) into a single bi-directional logical link carrying an Ethernet stream. This specification can be viewed as IEEE 802.3-2005 [802.3] Clause 61 Physical Medium Entity (PME) Aggregation, generalized to work over any xDSL technology (2Base-TL and 10Pass-TS interfaces defined by IEEE use G.SHDSL and VDSL technology respectively). o The Multi-pair bonding using time-division inverse multiplexing (TDIM), specified in ITU-T G.998.3 recommendation [G.998.3], which defines a method for bonding (or aggregating) of multiple xDSL lines into a single bi-directional logical link carrying a mix of various traffic streams (e.g., Ethernet, ATM, TDM). Architecturally all three bonding schemes define a new "bonded" Transport Protocol Specific - Transmission Convergence (TPS-TC) sub- layer, stacked above multiple ATM-TC, Ethernet/PTM-TC or STM-TC (clear channel) sub-layers for the ATM, Ethernet or TDIM bonding respectively. Each underlying TPS-TC sub-layer represents a protocol specific interface to an xDSL line or an individual bearer channel of an xDSL line. Bonding of multiple bearer channels in the same xDSL line is not allowed. All schemes allow bonding of up to 32 individual line/channel sub- layers with variable rates, providing common functionality for the configuration, initialization, operation and monitoring of the bonded Beili & Morgenstern Expires January 17, 2013 [Page 3] Internet-Draft G.Bond MIB Jul 2012 link. This document defines a MIB module common to all 3 schemes. Additional managed objects, specific to each bonding technology, are defined in G9981-MIB [I-D.ietf-adslmib-gbond-atm-mib], G9982-MIB [I-D.ietf-adslmib-gbond-eth-mib] and G9983-MIB [I-D.ietf-adslmib-gbond-tdim-mib] modules. The textual conventions listing the bonding schemes are defined in a separate, IANA-maintained MIB module, first version of which is provided in this document. This arrangement would allow for future bonding schemes to be easily supported, without the need to update the common GBOND-MIB module, 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This document specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 3. The DSL Forum Management Framework for xDSL Bonding This document makes use of the DSL Forum technical report Management Framework for xDSL Bonding [TR-159], defining a management model and a hierarchy of management objects for the bonded xDSL interfaces. 4. Relationship to Other MIB modules This section outlines the relationship of the MIB modules defined in this document with other MIB modules described in the relevant RFCs. Specifically, the following MIB modules are discussed: Interfaces Group MIB (IF-MIB), Inverse Stack Table MIB (IF-INVERTED-STACK-MIB) Interface Stack Capability MIB (IF-CAP-STACK-MIB), G.Bond scheme specific modules: G.Bond/ATM (G9981-MIB), G.Bond/Ethernet (G9982-MIB) Beili & Morgenstern Expires January 17, 2013 [Page 4] Internet-Draft G.Bond MIB Jul 2012 and G.Bond/TDIM (G9983-MIB), and DSL specific MIB modules: ADSL (ADSL-LINE-EXT-MIB), ADSL2 (ADSL2-LINE-MIB), SHDSL (HDSL2-SHDSL-LINE- MIB), VDSL (VDSL-LINE-MIB) and VDSL2 (VDSL2-LINE-MIB). 4.1. Relationship to Interfaces Group MIB module A bonded xDSL port is a stacked (a.k.a. aggregated or bonded) interface and as such is managed using generic interface management objects defined in the IF-MIB [RFC2863]. The stack management, i.e., actual connection of the sub-layers to the top layer interface, is done via the ifStackTable, as defined in the IF-MIB [RFC2863] and its inverse ifInvStackTable, as defined in the IF-INVERTED-STACK-MIB [RFC2864]. The ifCapStackTable and its inverse ifInvCapStackTable defined in the IF-CAP-STACK-MIB [RFC5066], extend the stack management with an ability to describe possible connections or cross-connect capability, when a flexible cross-connect matrix is present between the interface layers. 4.1.1. Layering Model A G.Bond interface can aggregate up to 32 channel sub-layers, with each channel representing an xDSL line or an xDSL bearer channel. For the purpose of brevity we will refer to the bonded interface as Generic Bonded Sub-layer (GBS) and to the channel sub-layer as Bonding Channel Entity (BCE). A generic G.Bond device can have a number of GBS ports, each connected to a particular upper layer (e.g., Media Access Control (MAC) interface for G.998.2 scheme), while simultaneously cross- connected to a number of underlying BCEs, with a single GBS per BCE relationship. A GBS port is represented in the Interface table (ifTable) as a separate interface with an ifType reflecting a particular bonding scheme, e.g., g9981(263), g9982(264) or g9983(265). Each BCE in the aggregated GBS port is represented in the ifTable as a separate interface with an ifType relevant to a particular xDSL technology, e.g., shdsl(169) or vdsl(97). The ifType values are defined in [IANAifType-MIB]. Beili & Morgenstern Expires January 17, 2013 [Page 5] Internet-Draft G.Bond MIB Jul 2012 The following figure shows the layering diagram and corresponding use of ifTable for the bonded xDSL interfaces: .-----------------------------. - | GBS | ^ 1 ifEntry | (TPS-TC) | v ifType: g9981(263), g9982(264) +-----------------+---+-------+ - g9983(265), etc. | TPS-TC \ | | | ^ +---------\ | | | | N ifEntry (N=1..32) | PMS-TC )BCE 1 |...| BCE N | ) ifType: adsl(94), shdsl(169), +---------/ | | | | vdsl(97), vdsl2(251), | PMD / | | | v etc. '-----------------+---+-------' - BCE - Bonding Channel Entity GBS - Generic Bonded Sub-layer PMD - Physical Medium Dependent TPS-TC - Transport Protocol Specific - Transmission Convergence PMS-TC - Physical Media Specific - Transmission Convergence Figure 1: Use of ifTable for bonded xDSL interfaces The ifStackTable is indexed by the ifIndex values of the aggregated G.Bond port (GBS) and the BCEs connected to it. ifStackTable allows a Network Management application to determine which BCEs are connected to a particular GBS and change connections (if supported by the application). The ifInvStackTable, being an inverted version of the ifStackTable, provides an efficient means for a Network Management application to read a subset of the ifStackTable and thereby determine which GBS runs on top of a particular BCE. The ifCapStackTable defined in the IF-CAP-STACK-MIB module, specifies for each higher-layer interface (e.g., GBS port) a list of lower- layer interfaces (e.g., BCEs), which can possibly be cross-connected to that higher-layer interface, determined by the cross-connect capability of the device. This table, modeled after ifStackTable, is read only, reflecting current cross-connect capability of a stacked interface, which can be dynamic in some implementations (e.g., if xDSL lines are located on a pluggable module and the module is pulled out). Note that BCE availability per GBS, described by ifCapStackTable, can be constrained by other parameters, for example by aggregation capacity of a GBS or by the BCE in question being already connected to another GBS. So, in order to ensure that a particular BCE can be connected to the GBS, all respective parameters (e.g., ifCapStackTable, ifStackTable and gBondPortCapCapacity) SHALL be inspected. The ifInvCapStackTable, also defined in the IF-CAP-STACK-MIB module, Beili & Morgenstern Expires January 17, 2013 [Page 6] Internet-Draft G.Bond MIB Jul 2012 describes which higher-layer interfaces (e.g., GBS ports) can possibly be connected to a particular lower-layer interface (e.g., BCE), providing inverted mapping of ifCapStackTable. While it contains no additional information beyond that already contained in the ifCapStackTable, the ifInvCapStackTable has the ifIndex values in its INDEX clause in the reverse order, i.e., the lower-layer interface first, and the higher-layer interface second, providing efficient means for a Network Management application to read a subset of the ifCapStackTable and thereby determine which interfaces can be connected to run on top of a particular interface. 4.1.2. xDSL Bonding The G.998.x Bonding allows a number of BCEs to be aggregated onto a single logical GBS port, by splitting the incoming traffic into multiple streams, transmitting each stream over a specific BCE and combining the streams at the remote GBS port, preserving the original traffic order. The Ethernet frames MAY be fragmented before the transmission and reassembled at the remote end to minimize transportation delay. The G.998.2 (G.Bond/Ethernet) ports with multiple BCEs MUST perform the fragmentation and reassembly of the Ethernet frames. However for a single-BCE G.998.2 ports this function MAY be omitted (a.k.a. bonding bypass), to minimize fragmentation overhead and additional processing delay as well as to be able to interoperate with non-G.998 DSL equipment. The agent is REQUIRED to indicate all supported bonding schemes (for example ATM, Ethernet and TDIM), including OPTIONAL support for the bonding bypass in G.998.2 single-BCE ports. The GBOND-MIB module allows a Network Management application to query Bonding capability and enable/disable it if supported. Note that enabling Bonding (by setting the value of gBondPortConfAdminScheme and gBondPortConfAdminScheme objects to any supported bonding scheme other than 'none') effectively turns on fragmentation and re-assembly function, even on a single-BCE port. 4.1.3. Discovery Operation The G.Bond ports may optionally support discovery operation, whereby BCEs, during initialization, exchange information about their respective aggregation groups (GBS), via [G.994.1] handshake (G.hs) protocol. This information can then be used to detect copper misconnections or for an automatic assignment of the local BCEs into aggregation groups instead of a fixed pre-configuration. Beili & Morgenstern Expires January 17, 2013 [Page 7] Internet-Draft G.Bond MIB Jul 2012 The MIB module defined in this document allow a Network Management application to control G.Bond discovery mechanism and query its results. Two tables are used by the G.Bond discovery mechanism: ifStackTable and ifCapStackTable. The following pseudo-code gives an example of the discovery and automatic BCE assignment for a generic multi-GBS G.Bond device, located at Central Office (CO), using objects defined in this MIB module, IF-CAP-STACK-MIB and IF-MIB modules [Note that automatic BCE assignment is only shown here for the purposes of the example. Fixed BCE pre-assignment, manual assignment or auto- assignment using an alternative internal algorithm may be chosen by a particular implementation]: // Go over all GBS ports in the CO device FOREACH gbs[i] IN CO_device { // Perform discovery and auto-assignment on GBS ports // with room for more Channels IF ( gbs[i].NumBCEs < gbs[i].BondCapacity ) { // Assign a unique 6-octets local discovery code to the GBS // e.g., MAC address of the associated port or some other // unique number specifically allocated for this purpose. dc = gbs[i].DiscoveryCode = MAC[i]; // Go over all disconnected Channels, which can // potentially be connected to the GBS FOREACH bce[j] IN ifCapStackTable[gbs[i]] AND NOT IN ifStackTable[gbs[i]] // not connected { // Try to grab the remote RT_device, by writing the value // of the local 6 Byte discovery code to the remote // discovery code register (via handshake mechanism). // This operation is atomic Set-if-Clear action, i.e., it // would succeed only if the remote discovery register was // zero. Read the remote discovery code register via Get // operation to see if the RT_device, attached via the BCE // is indeed marked as being the CO_device peer. bce[j].RemoteDiscoveryCode = dc; // Set-if-Clear r = bce[j].RemoteDiscoveryCode; // Get IF ( r == dc AND gbs[i].NumBCEs < gbs[i].BondCapacity) { // Remote RT_device connected via BCE[j] is/was a peer // for GBS[i] and there room for another BCE in the // GBS[i] aggregation group (max. Bonding capacity is // not reached yet). // Connect this BCE to the GBS (via ifStackTable, // ifInvStackTable being inverse of ifStackTable is // updated automatically, i.e., gbs[i] is auto-added // to ifInvStackTable[bce[j]]) ADD bce[j] TO ifStackTable[gbs[i]]; gbs[i].NumBCEs = gbs[i].NumBCEs + 1; Beili & Morgenstern Expires January 17, 2013 [Page 8] Internet-Draft G.Bond MIB Jul 2012 // Discover all other disconnected BCEs, // attached to the same RT_device and connect them to // the GBS provided there is enough room for more BCEs. FOREACH bce[k] IN ifCapStackTable[gbs[i]] and NOT IN ifStackTable[gbs[i]] { // Get Remote Discovery Code from the BCE to see if // it belongs to a connected RT_device "grabbed" by // the CO_device. r = bce[k].RemoteDiscoveryCode; IF ( r == dc AND gbs[i].NumBCEs < gbs[i].BondCapacity) { // Physically connect the BCE to the GBS // (gbs[i] is auto-added TO ifInvStackTable[bce[k]]) ADD bce[k] TO ifStackTable[gbs[i]]; gbs[i].NumBCEs = gbs[i].NumBCEs + 1; } } } // At this point we have discovered all local BCEs which // are physically connected to the same remote RT_device // and connected them to GBS[i]. Go to the next GBS. BREAK; } } } An SNMP Agent for a G.Bond device builds ifCapStackTable and its inverse ifInvCapStackTable on device initialization, according to the cross-connect capabilities of the device. Adding a BCE to the ifStackTable row for a specific GBS, involves actual connection of the BCE to the GBS. Note that GBS port does not have to be operationally 'down' for the connection to succeed. In fact, a dynamic BCE addition (and removal) MAY be implemented with an available BCE being initialized first (by setting its ifAdminStatus to 'up') and then added to an operationally 'up' GBS port, by modifying a respective ifStackTable (and respective ifInvStackTable) entry. It is RECOMMENDED that a removal of the last operationally 'up' BCE from an operationally 'up' GBS, i.e. modification of a respective entry in ifStackTable and a corresponding entry in ifInvStackTable, would be rejected by the implementation (in case of SNMP with the error inconsistentValue), as this action would completely drop the link. In addition to the standard handshake-based discovery described above, [G.998.2] defines an optional frame-based discovery and pair Beili & Morgenstern Expires January 17, 2013 [Page 9] Internet-Draft G.Bond MIB Jul 2012 management. These frame-based methods are discussed in [I-D.ietf-adslmib-gbond-eth-mib]. 4.1.4. G.Bond ports initialization G.Bond ports being built on top of xDSL technology, require a lengthy initialization or 'training' process, before any data can pass. During this initialization both ends of a link (peers) work cooperatively to achieve required data rate on a particular copper pair. Sometimes, when the copper line is too long or the noise on the line is too high, that 'training' process may fail to achieve a specific target rate with required characteristics. The ifAdminStatus object from the IF-MIB, controls the desired state of a GBS with all the BCEs connected to it or of an individual BCE port. Setting this object to 'up' instructs a particular GBS or a BCE to start initialization process, which may take tens of seconds for G.Bond ports. The ifOperStatus object from the IF-MIB shows the operational state of an interface for GBS, extended by gBondPortStatFltStatus object defined in this document, and corresponding *Status object from a relevant xDSL line MIB for BCE interfaces. A disconnected BCE may be initialized by changing the ifAdminState from 'down' to 'up'. Changing the ifAdminState to 'up' on the GBS initializes all BCEs connected to that particular GBS. Note that in case of bonding some interfaces may fail to initialize while others succeed. The GBS is considered operationally 'up' if at least one bonded BCE is operationally 'up'. When all BCEs connected to the GBS are 'down' the GBS SHALL be considered operationally 'lowerLayerDown'. The GBS SHALL be considered operationally 'notPresent' if it is not connected to any BCE. The GBS/BCE interface SHALL remain operationally 'down' during initialization, indicated by 'init' value of the gBondPortStatFltStatus object. 4.1.5. Usage of ifTable Both BCE and GBS interfaces are managed using interface specific management objects defined in the GBOND-MIB module and generic interface objects from the ifTable of IF-MIB, with all management table entries referenced by the interface index ifIndex. The following table summarizes G.Bond specific interpretations for some of the ifTable objects specified by the mandatory ifGeneralInformationGroup: Beili & Morgenstern Expires January 17, 2013 [Page 10] Internet-Draft G.Bond MIB Jul 2012 +---------------+---------------------------------------------------+ | IF-MIB object | G.Bond interpretation | +---------------+---------------------------------------------------+ | ifIndex | Interface index. Note that each BCE and each GBS | | | in the G.Bond PHY MUST have a unique index, as | | | there are some GBS and BCE specific attributes | | | accessible only on the GBS or BCE level. | +---------------+---------------------------------------------------+ | ifType | g9981(263), g9982(264) or g9983(265) for the ATM, | | | Ethernet or TDIM GBS respectively, shdsl(169) for | | | G.SHDSL BCE, vdsl(97) for VDSL BCE, etc. | +---------------+---------------------------------------------------+ | ifSpeed | Operating data rate for the BCE. For the GBS it | | | is the sum of the current operating data rates of | | | all BCEs in the aggregation group, without the | | | encapsulation overhead and G.Bond overhead, but | | | accounting for the Inter-Frame Gaps (IFG). When a | | | GBS or a BCE is operating in an asymetrical | | | fashion (upstream data rate differs from the | | | downstream one) the lowest of the values is | | | shown. | +---------------+---------------------------------------------------+ | ifAdminStatus | Setting this object to 'up' instructs a | | | particular GBS (with all BCEs connected to it) or | | | a BCE to start initialization process | +---------------+---------------------------------------------------+ | ifOperStatus | A relevant *Status object from a particular line | | | MIB supplements the value of ifOperStatus for | | | BCEs. gBondPortStatFltStatus supplements the | | | value of ifOperStatus for GBS. Note that both | | | relevant objects shall be inspected to determine | | | the real operational status of a BCE/GBS port, | | | e.g. a GBS port may be operationally 'up' with | | | gBondPortStatFltStatus indicating lowRate(4) | | | fault condition, or 'down' with no gBond faults. | +---------------+---------------------------------------------------+ Table 1: G.Bond interpretation of IF-MIB objects 4.2. Relationship to G.Bond ATM, ETH and TDIM MIB modules The MIB module defined in this document is common to all G.998 bonding schemes. It MUST be used in conjunction with a bonding scheme-specific MIB module: o G9981-MIB [I-D.ietf-adslmib-gbond-atm-mib] for a G.998.1 bonded interface. Beili & Morgenstern Expires January 17, 2013 [Page 11] Internet-Draft G.Bond MIB Jul 2012 o G9982-MIB [I-D.ietf-adslmib-gbond-eth-mib] for a G.998.2 bonded interface. o G9983-MIB [I-D.ietf-adslmib-gbond-tdim-mib] for a G.998.3 bonded interface. 4.3. Relationship to xDSL MIB modules Each xDSL technology is described in a relevant xDSL line MIB module: e.g., HDSL2-SHDSL-LINE-MIB [RFC4319] for G.SHDSL, ADSL-LINE-EXT-MIB [RFC3440] for ADSL, ADSL2-LINE-MIB [RFC4706] for ADSL2, VDSL-LINE-MIB [RFC3728] for VDSL or VDSL2-LINE-MIB [RFC5650] for VDSL2. These MIB moduless are used to manage individual xDSL lines/channels (BCEs). 4.4. Addition of new bonding schemes In case a new bonding scheme is introduced in a revision of G.998, IANA can update the IANA-maintained MIB module, adding the corresponding new value, to the IANAgBondScheme and IANAgBondSchemeList textual conventions, as well as listing the new scheme-specific MIB module's name (e.g. G998x-MIB). Any scheme-specific aspect of an existing GBOND-MIB object SHALL be described in the corresponding G998x-MIB module, to prevent an unnesessary re-issue of the GBOND-MIB module. For example, an exact definition of an Errored Second (ES) or a Severely Errored Second (SES) can be bonding-scheme specific, see the definition for gBondPortPmCurES and gBondPortPmCurSES objects. 5. MIB Structure 5.1. Overview The main management objects defined in the GBOND-MIB module are split into 2 groups, structured as recommended by RFC 4181 [RFC4181]: o gBondPort - containing objects for configuration, capabilities, status, historical performance monitoring and notifications, common to all G.Bond ports (GBS). o gBondBce - containing a single common object for configuration of the remote discovery code per BCE. Note that the rest of the objects for BCE configuration, capabilities, status and notifications, is located in relevant xDSL line MIB modules as well as in the bonding scheme specific MIB modules. Beili & Morgenstern Expires January 17, 2013 [Page 12] Internet-Draft G.Bond MIB Jul 2012 5.2. Performance Monitoring The OPTIONAL performance monitoring counters, thresholds and history buckets (interval-counters) defined in [TR-159] are implemented using the textual conventions defined in the HC-PerfHist-TC-MIB [RFC3705]. The HC-PerfHist-TC-MIB defines 64-bit versions of the textual conventions found in PerfHist-TC-MIB [RFC3593]. The agent SHOULD align the beginning of each interval to a fifteen minute boundary of a wall clock. Likewise, the beginning of each one day intervals SHOULD be aligned with the start of a day. The rationale behind it is to simplify collection and analysis of the PM from multiple agents by a network management system (NMS) - each PM interval can be "time-stamped" using the gBond*IntervalIndex object, the fact that 1-day interval starts at 00:00 and 15-min intervals are aligned with 1/4 hour and the network-wide "wall clock", typically distributed via NTP or SNTP [RFC5905]. If the agent does not have an access to the wall clock, a local clock can be used. In this case, as well as when coping with multiple time zones, the NMS would have to correlate for the difference between the agent's local clock (available for example via hrSystemDate object from HOST-RESOURCES-MIB [RFC2790]) and the wall clock. Counters are not reset when a GBS is reinitialized, but rather only when the agent is reset or reinitialized. Note that the accumulation of certain performance events for a monitored entity is inhibited (counting stops) during periods of service unavailability on that monitored entity. The DESCRIPTION clause of performance monitoring counters in this MIB module specifies which of the counters are inhibited during periods of service unavailability. 5.3. Mapping of DSL Forum TR-159 Managed Objects This section contains the mapping between relevant managed objects (attributes) defined in [TR-159] and managed objects defined in this document and in associated MIB modules, i.e., the IF-MIB [RFC2863]. +-------------------------------+-----------------------------------+ | G.Bond Managed Object | Corresponding SNMP Object | +-------------------------------+-----------------------------------+ | oBondingGroup - Basic Package | | | (Mandatory) | | +-------------------------------+-----------------------------------+ | aGroupID | ifIndex (IF-MIB) | +-------------------------------+-----------------------------------+ Beili & Morgenstern Expires January 17, 2013 [Page 13] Internet-Draft G.Bond MIB Jul 2012 +-------------------------------+-----------------------------------+ | aGroupBondSchemesSupported | gBondPortCapSchemesSupported | +-------------------------------+-----------------------------------+ | aGroupPeerBondSchemesSupporte | gBondPortCapPeerSchemesSupported | | d | | +-------------------------------+-----------------------------------+ | aGroupAdminBondScheme | gBondPortConfAdminScheme | +-------------------------------+-----------------------------------+ | aGroupPeerAdminBondScheme | gBondPortConfPeerAdminScheme | +-------------------------------+-----------------------------------+ | aGroupOperBondScheme | gBondPortStatOperScheme | +-------------------------------+-----------------------------------+ | aGroupPeerOperBondScheme | gBondPortStatPeerOperScheme | +-------------------------------+-----------------------------------+ | aGroupEnd | gBondPortStatSide | +-------------------------------+-----------------------------------+ | aGroupOperState | ifOperStatus (IF-MIB) | +-------------------------------+-----------------------------------+ | aGroupAdminState | ifAdminStatus (IF-MIB) | +-------------------------------+-----------------------------------+ | aGroupStatus | gBondPortStatFltStatus | +-------------------------------+-----------------------------------+ | aGroupCapacity | gBondPortCapCapacity | +-------------------------------+-----------------------------------+ | aGroupPeerCapacity | gBondPortCapPeerCapacity | +-------------------------------+-----------------------------------+ | aGroupNumChannels | gBondPortStatNumBCEs | +-------------------------------+-----------------------------------+ | aGroupName | ifName (IF-MIB) | +-------------------------------+-----------------------------------+ | aGroupDiscoveryCode | gBondPortConfDiscoveryCode | +-------------------------------+-----------------------------------+ | aGroupUpRate | gBondPortStatUpDataRate | +-------------------------------+-----------------------------------+ | aGroupDownRate | gBondPortStatDnDataRate | +-------------------------------+-----------------------------------+ | aGroupTargetUpRate | gBondPortConfTargetUpDataRate | +-------------------------------+-----------------------------------+ | aGroupTargetDownRate | gBondPortConfTargetDnDataRate | +-------------------------------+-----------------------------------+ | aGroupThreshLowUpRate | gBondPortConfThreshLowUpRate | +-------------------------------+-----------------------------------+ | aGroupThreshLowDownRate | gBondPortConfThreshLowDnRate | +-------------------------------+-----------------------------------+ | aGroupLowRateCrossingEnable | gBondPortConfLowRateCrossingEnabl | | | e | +-------------------------------+-----------------------------------+ | nGroupLowUpRateCrossing | gBondLowUpRateCrossing | Beili & Morgenstern Expires January 17, 2013 [Page 14] Internet-Draft G.Bond MIB Jul 2012 | nGroupLowDownRateCrossing | gBondLowDnRateCrossing | +-------------------------------+-----------------------------------+ | aGroupLinkUpDownEnable | ifLinkUpDownTrapEnable (IF-MIB) | +-------------------------------+-----------------------------------+ | nGroupLinkUp | linkDown (IF-MIB) | +-------------------------------+-----------------------------------+ | nGroupLinkDown | linkUp (IF-MIB) | +-------------------------------+-----------------------------------+ | oBondingGroup - PM Package | | | (Optional) | | +-------------------------------+-----------------------------------+ | aGroupPerfES | gBondPortPmCurES | +-------------------------------+-----------------------------------+ | aGroupPerfSES | gBondPortPmCurSES | +-------------------------------+-----------------------------------+ | aGroupPerfUAS | gBondPortPmCurUAS | +-------------------------------+-----------------------------------+ | aGroupPerf15MinValidIntervals | gBondPortPmCur15MinValidIntervals | +-------------------------------+-----------------------------------+ | aGroupPerf15MinInvalidInterva | gBondPortPmCur15MinInvalidInterva | | ls | ls | +-------------------------------+-----------------------------------+ | aGroupPerfCurr15MinTimeElapse | gBondPortPmCur15MinTimeElapsed | | d | | +-------------------------------+-----------------------------------+ | aGroupPerfCurr15MinES | gBondPortPmCur15MinES | +-------------------------------+-----------------------------------+ | aGroupPerfCurr15MinSES | gBondPortPmCur15MinSES | +-------------------------------+-----------------------------------+ | aGroupPerfCurr15MinUAS | gBondPortPmCur15MinUAS | +-------------------------------+-----------------------------------+ | aGroupPerfTcaEnable | gBondPortConfPmTcaEnable | +-------------------------------+-----------------------------------+ | aGroupPerfThreshold15MinES | gBondPortPmTcaProfileThresh15MinE | | | S | +-------------------------------+-----------------------------------+ | aGroupPerfThreshold15MinSES | gBondPortPmTcaProfileThresh15MinS | | | ES | +-------------------------------+-----------------------------------+ | aGroupPerfThreshold15MinUAS | gBondPortPmTcaProfileThresh15MinU | | | AS | +-------------------------------+-----------------------------------+ | nGroupPerfTca15MinES | gBondPmTca15MinESCrossing | +-------------------------------+-----------------------------------+ | nGroupPerfTca15MinSES | gBondPmTca15MinSESCrossing | +-------------------------------+-----------------------------------+ | nGroupPerfTca15MinUAS | gBondPmTca15MinUASCrossing | +-------------------------------+-----------------------------------+ Beili & Morgenstern Expires January 17, 2013 [Page 15] Internet-Draft G.Bond MIB Jul 2012 +-------------------------------+-----------------------------------+ | aGroupPerf1DayValidIntervals | gBondPortPmCur1DayValidIntervals | +-------------------------------+-----------------------------------+ | aGroupPerf1DayInvalidInterval | gBondPortPmCur1DayInvalidInterval | | s | s | +-------------------------------+-----------------------------------+ | aGroupPerfCurr1DayTimeElapsed | gBondPortPmCur1DayTimeElapsed | +-------------------------------+-----------------------------------+ | aGroupPerfCurr1DayES | gBondPortPmCur1DayIntervalES | +-------------------------------+-----------------------------------+ | aGroupPerfCurr1DaySES | gBondPortPmCur1DayIntervalSES | +-------------------------------+-----------------------------------+ | aGroupPerfCurr1DayUAS | gBondPortPmCur1DayIntervalUAS | +-------------------------------+-----------------------------------+ | aGroupPerfThreshold1DayES | gBondPortPmTcaProfileThresh1DayES | +-------------------------------+-----------------------------------+ | aGroupPerfThreshold1DaySES | gBondPortPmTcaProfileThresh1DaySE | | | S | +-------------------------------+-----------------------------------+ | aGroupPerfThreshold1DayUAS | gBondPortPmTcaProfileThresh1DayUA | | | S | +-------------------------------+-----------------------------------+ | nGroupPerfTca1DayES | gBondPmTca1DayESCrossing | +-------------------------------+-----------------------------------+ | nGroupPerfTca1DaySES | gBondPmTca1DaySESCrossing | +-------------------------------+-----------------------------------+ | nGroupPerfTca1DayUAS | gBondPmTca1DayUASCrossing | +-------------------------------+-----------------------------------+ | aGroupPerf15MinIntervalNumber | gBondPortPm15MinIntervalIndex | +-------------------------------+-----------------------------------+ | aGroupPerf15MinIntervalValid | gBondPortPm15MinIntervalValid | +-------------------------------+-----------------------------------+ | aGroupPerf15MinIntervalES | gBondPortPm15MinIntervalES | +-------------------------------+-----------------------------------+ | aGroupPerf15MinIntervalSES | gBondPortPm15MinIntervalSES | +-------------------------------+-----------------------------------+ | aGroupPerf15MinIntervalUAS | gBondPortPm15MinIntervalUAS | +-------------------------------+-----------------------------------+ | aGroupPerf1DayIntervalNumber | gBondPortPm1DayIntervalIndex | +-------------------------------+-----------------------------------+ | aGroupPerf1DayIntervalValid | gBondPortPm1DayIntervalValid | +-------------------------------+-----------------------------------+ | aGroupPerf1DayIntervalMoniSec | gBondPortPm1DayIntervalMoniTime | | s | | +-------------------------------+-----------------------------------+ | aGroupPerf1DayIntervalES | gBondPortPm1DayIntervalES | +-------------------------------+-----------------------------------+ | aGroupPerf1DayIntervalSES | gBondPortPm1DayIntervalSES | Beili & Morgenstern Expires January 17, 2013 [Page 16] Internet-Draft G.Bond MIB Jul 2012 | aGroupPerf1DayIntervalUAS | gBondPortPm1DayIntervalUAS | +-------------------------------+-----------------------------------+ | oLine - Basic Package | | | (Mandatory) | | +-------------------------------+-----------------------------------+ | aLineID | ifIndex (IF-MIB) | +-------------------------------+-----------------------------------+ | aLineType | ifType (IF-MIB) | +-------------------------------+-----------------------------------+ | aLineOperState | ifOperStatus (IF-MIB) | +-------------------------------+-----------------------------------+ | aLineStatus | *dsl*CurrStatus (*DSL-LINE-MIB) | +-------------------------------+-----------------------------------+ | aLineEnd | *dsl*Side (*DSL-LINE-MIB) | +-------------------------------+-----------------------------------+ | aLineAdminState | ifAdminStatus (IF-MIB) | +-------------------------------+-----------------------------------+ | aLineRemoteDiscoveryCode | gBondBceConfRemoteDiscoveryCode | +-------------------------------+-----------------------------------+ | aLineUpDownEnable | ifLinkUpDownTrapEnable (IF-MIB) | +-------------------------------+-----------------------------------+ | nLineUp | linkUp (IF-MIB) | +-------------------------------+-----------------------------------+ | nLineDown | linkDown (IF-MIB) | +-------------------------------+-----------------------------------+ | oChannel - Basic Package | | | (Mandatory) | | +-------------------------------+-----------------------------------+ | aChannelID | ifIndex (IF-MIB) | +-------------------------------+-----------------------------------+ | aChannelGroupID | | +-------------------------------+-----------------------------------+ | aChannelType | ifType (IF-MIB) | +-------------------------------+-----------------------------------+ | aChannelOperState | ifOperStatus (IF-MIB) | +-------------------------------+-----------------------------------+ | aChannelStatus | *dsl*CurrStatus (*DSL-LINE-MIB), | | | xdsl2ChStatus*Status | | | (VDSL2-LINE-MIB) | +-------------------------------+-----------------------------------+ Table 2: Mapping of TR-159 Managed Objects 6. xDSL Multi-pair Bonding MIB Definitions GBOND-MIB DEFINITIONS ::= BEGIN IMPORTS Beili & Morgenstern Expires January 17, 2013 [Page 17] Internet-Draft G.Bond MIB Jul 2012 MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Unsigned32, Gauge32 FROM SNMPv2-SMI -- [RFC2578] TEXTUAL-CONVENTION, TruthValue, RowStatus, PhysAddress FROM SNMPv2-TC -- [RFC2579] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] ifIndex FROM IF-MIB -- [RFC2863] HCPerfCurrentCount, HCPerfIntervalCount, HCPerfIntervalThreshold, HCPerfValidIntervals, HCPerfInvalidIntervals, HCPerfTimeElapsed, HCPerfTotalCount FROM HC-PerfHist-TC-MIB -- [RFC3705] IANAgBondScheme, IANAgBondSchemeList FROM IANA-GBOND-TC-MIB ; ------------------------------------------------------------------------ gBondMIB MODULE-IDENTITY LAST-UPDATED "201207160000Z" -- Jul 16, 2012 ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO "WG charter: http://www.ietf.org/html.charters/adslmib-charter.html Mailing Lists: General Discussion: adslmib@ietf.org To Subscribe: adslmib-request@ietf.org In Body: subscribe your_email_address Chair: Menachem Dodge Postal: ECI Telecom, Ltd. 30 Hasivim St., Beili & Morgenstern Expires January 17, 2013 [Page 18] Internet-Draft G.Bond MIB Jul 2012 Petach-Tikva 4951169 Israel Phone: +972-3-926-8421 EMail: menachem.dodge@ecitele.com Editor: Edward Beili Postal: Actelis Networks, Inc. 25 Bazel St., P.O.B. 10173 Petach-Tikva 49103 Israel Phone: +972-3-924-3491 EMail: edward.beili@actelis.com Editor: Moti Morgenstern Postal: ECI Telecom 30 Hasivim St. Petach-Tikva 4951169 Israel Phone: +972-3-926-6258 EMail: moti.morgenstern@ecitele.com" DESCRIPTION "The objects in this MIB module are used to manage the multi-pair bonded xDSL Interfaces, defined in ITU-T recommendations G.998.1, G.998.2 and G.998.3. This MIB module MUST be used in conjunction with a bonding scheme specific MIB module, that is, G9981-MIB, G9982-MIB or G9983-MIB. The following references are used throughout this MIB module: [G.998.1] refers to: ITU-T Recommendation G.998.1: 'ATM-based multi-pair bonding', January 2005. [G.998.2] refers to: ITU-T Recommendation G.998.2: 'Ethernet-based multi-pair bonding', January 2005. [G.998.3] refers to: ITU-T Recommendation G.998.3: 'Multi-pair bonding using time-division inverse multiplexing', January 2005. [TR-159] refers to: Broadband Forum Technical Report: 'Management Framework for xDSL Bonding', December 2008. Beili & Morgenstern Expires January 17, 2013 [Page 19] Internet-Draft G.Bond MIB Jul 2012 Naming Conventions: BCE - Bonding Channel Entity BTU - Bonding Transmission Unit BTU-C - Bonding Transmission Unit, CO side BTU-R - Bonding Transmission Unit, Remote Terminal (CPE) side CO - Central Office CPE - Customer Premises Equipment GBS - Generic Bonding Sublayer PM - Performance Monitoring SNR - Signal to Noise Ratio TCA - Threshold Crossing Alert Copyright (C) The IETF Trust (2012). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices." REVISION "201207160000Z" -- Jul 16, 2012 DESCRIPTION "Initial version, published as RFC XXXX." -- EdNote: Replace XXXX with the actual RFC number & -- remove this note ::= { mib-2 ZZZ } -- EdNote: Replace ZZZ with a real OID once it is -- allocated & remove this note. -- Sections of the module -- Structured as recommended by [RFC4181], Appendix D gBondObjects OBJECT IDENTIFIER ::= { gBondMIB 1 } gBondConformance OBJECT IDENTIFIER ::= { gBondMIB 2 } -- Groups in the module gBondPort OBJECT IDENTIFIER ::= { gBondObjects 1 } gBondBce OBJECT IDENTIFIER ::= { gBondObjects 2 } -- Textual Conventions GBondPm1DayIntervalThreshold ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "This textual convention defines a range of values that may be set in a fault threshold alarm control for a 1-day performance Beili & Morgenstern Expires January 17, 2013 [Page 20] Internet-Draft G.Bond MIB Jul 2012 monitoring interval. As the number of seconds in a 1-day interval numbers at most 86400, objects of this type may have a range of 0...86400, where the value of 0 disables the alarm." SYNTAX Unsigned32 (0..86400) -- Port Notifications Group gBondPortNotifications OBJECT IDENTIFIER ::= { gBondPort 0 } gBondLowUpRateCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortStatUpDataRate, gBondPortConfThreshLowUpRate } STATUS current DESCRIPTION "This notification indicates that the G.Bond port's upstream data rate has reached/dropped below or exceeded the low upstream rate threshold, specified by gBondPortConfThreshLowUpRate. This notification MAY be sent for the -O subtype ports while the port is up, on the crossing event in both directions: from normal (rate is above the threshold) to low (rate equals the threshold or below it) and from low to normal. This notification is not applicable to the -R subtypes. It is RECOMMENDED that a small debouncing period of 2.5 sec, between the detection of the condition and notification, is implemented to prevent simultaneous LinkUp/LinkDown and gBondLowUpRateCrossing notifications to be sent. The adaptive nature of the G.Bond technology allows the port to adapt itself to the changes in the copper environment, e.g., an impulse noise, alien crosstalk, or a micro-interruption may temporarily drop one or more BCEs in the aggregation group, causing a rate degradation of the aggregated G.Bond link. The dropped BCEs would then try to re-initialize, possibly at a lower rate than before, adjusting the rate to provide required target SNR margin. Generation of this notification is controlled by the gBondPortConfLowRateCrossingEnable object. Beili & Morgenstern Expires January 17, 2013 [Page 21] Internet-Draft G.Bond MIB Jul 2012 This object maps to the TR-159 notification nGroupLowUpRateCrossing." REFERENCE "[TR-159] 5.5.1.24" ::= { gBondPortNotifications 1 } gBondLowDnRateCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortStatDnDataRate, gBondPortConfThreshLowDnRate } STATUS current DESCRIPTION "This notification indicates that the G.Bond port's downstream data rate has reached/dropped below or exceeded the low downstream rate threshold, specified by gBondPortConfThreshLowDnRate. This notification MAY be sent for the -O subtype ports while the port is up, on the crossing event in both directions: from normal (rate is above the threshold) to low (rate equals the threshold or below it) and from low to normal. This notification is not applicable to the -R subtypes. It is RECOMMENDED that a small debouncing period of 2.5 sec, between the detection of the condition and notification, is implemented to prevent simultaneous LinkUp/LinkDown and gBondLowDnRateCrossing notifications to be sent. The adaptive nature of the G.Bond technology allows the port to adapt itself to the changes in the copper environment, e.g., an impulse noise, alien crosstalk, or a micro-interruption may temporarily drop one or more BCEs in the aggregation group, causing a rate degradation of the aggregated G.Bond link. The dropped BCEs would then try to re-initialize, possibly at a lower rate than before, adjusting the rate to provide required target SNR margin. Generation of this notification is controlled by the gBondPortConfLowRateCrossingEnable object. This object maps to the TR-159 notification nGroupLowDownRateCrossing." REFERENCE "[TR-159] 5.5.1.25" ::= { gBondPortNotifications 2} Beili & Morgenstern Expires January 17, 2013 [Page 22] Internet-Draft G.Bond MIB Jul 2012 gBondPmTca15MinESCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortPmCur15MinES, gBondPortPmTcaProfileThresh15MinES } STATUS current DESCRIPTION "This notification indicates that the Errored Seconds threshold, specified by gBondPortPmTcaProfileThresh15MinES, has been reached or exceeded for the GPS port. Generation of this notification is controlled by gBondPortConfPmTcaEnable and gBondPortPmTcaProfileThresh15MinES objects. This object maps to the TR-159 notification nGroupPerfTca15MinES." REFERENCE "[TR-159] 5.5.1.42" ::= { gBondPortNotifications 3} gBondPmTca15MinSESCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortPmCur15MinSES, gBondPortPmTcaProfileThresh15MinSES } STATUS current DESCRIPTION "This notification indicates that the Severely Errored Seconds threshold, specified by gBondPortPmTcaProfileThresh15MinSES, has been reached or exceeded for the GPS port. Generation of this notification is controlled by gBondPortConfPmTcaEnable and gBondPortPmTcaProfileThresh15MinSES objects. This object maps to the TR-159 notification nGroupPerfTca15MinSES." REFERENCE "[TR-159] 5.5.1.43" ::= { gBondPortNotifications 4} gBondPmTca15MinUASCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortPmCur15MinUAS, Beili & Morgenstern Expires January 17, 2013 [Page 23] Internet-Draft G.Bond MIB Jul 2012 gBondPortPmTcaProfileThresh15MinUAS } STATUS current DESCRIPTION "This notification indicates that the Unavailable Seconds threshold, specified by gBondPortPmTcaProfileThresh15MinES, has been reached or exceeded for the GPS port. Generation of this notification is controlled by gBondPortConfPmTcaEnable and gBondPortPmTcaProfileThresh15MinUAS objects. This object maps to the TR-159 notification nGroupPerfTca15MinUAS." REFERENCE "[TR-159] 5.5.1.44" ::= { gBondPortNotifications 5} gBondPmTca1DayESCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortPmCur1DayES, gBondPortPmTcaProfileThresh1DayES } STATUS current DESCRIPTION "This notification indicates that the Errored Seconds threshold, specified by gBondPortPmTcaProfileThresh1DayES, has been reached or exceeded for the GPS port. Generation of this notification is controlled by gBondPortConfPmTcaEnable and gBondPortPmTcaProfileThresh1DayES objects. This object maps to the TR-159 notification nGroupPerfTca1DayES." REFERENCE "[TR-159] 5.5.1.54" ::= { gBondPortNotifications 6} gBondPmTca1DaySESCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortPmCur1DaySES, gBondPortPmTcaProfileThresh1DaySES } STATUS current DESCRIPTION Beili & Morgenstern Expires January 17, 2013 [Page 24] Internet-Draft G.Bond MIB Jul 2012 "This notification indicates that the Severely Errored Seconds threshold, specified by gBondPortPmTcaProfileThresh1DaySES, has been reached or exceeded for the GPS port. Generation of this notification is controlled by gBondPortConfPmTcaEnable and gBondPortPmTcaProfileThresh1DaySES objects. This object maps to the TR-159 notification nGroupPerfTca1DaySES." REFERENCE "[TR-159] 5.5.1.55" ::= { gBondPortNotifications 7} gBondPmTca1DayUASCrossing NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here since we are under specific GBS gBondPortPmCur1DayUAS, gBondPortPmTcaProfileThresh1DayUAS } STATUS current DESCRIPTION "This notification indicates that the Unavailable Seconds threshold, specified by gBondPortPmTcaProfileThresh1DayUAS, has been reached or exceeded for the GPS port. Generation of this notification is controlled by gBondPortConfPmTcaEnable and gBondPortPmTcaProfileThresh1DayUAS objects. This object maps to the TR-159 notification nGroupPerfTca1DayUAS." REFERENCE "[TR-159] 5.5.1.56" ::= { gBondPortNotifications 8} -- G.Bond Port (GBS) group gBondPortConfTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for configuration of G.Bond GBS ports. Entries in this table MUST be maintained in a persistent manner" ::= { gBondPort 1 } gBondPortConfEntry OBJECT-TYPE Beili & Morgenstern Expires January 17, 2013 [Page 25] Internet-Draft G.Bond MIB Jul 2012 SYNTAX GBondPortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond Port Configuration table. Each entry represents a G.Bond port indexed by the ifIndex. Note that a G.Bond GBS port runs on top of a single or multiple BCE port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { gBondPortConfTable 1 } GBondPortConfEntry ::= SEQUENCE { gBondPortConfAdminScheme IANAgBondScheme, gBondPortConfPeerAdminScheme IANAgBondScheme, gBondPortConfDiscoveryCode PhysAddress, gBondPortConfTargetUpDataRate Unsigned32, gBondPortConfTargetDnDataRate Unsigned32, gBondPortConfThreshLowUpRate Unsigned32, gBondPortConfThreshLowDnRate Unsigned32, gBondPortConfLowRateCrossingEnable TruthValue, gBondPortConfPmTcaConfProfile SnmpAdminString, gBondPortConfPmTcaEnable TruthValue } gBondPortConfAdminScheme OBJECT-TYPE SYNTAX IANAgBondScheme MAX-ACCESS read-write STATUS current DESCRIPTION "A desired bonding scheme for a G.Bond GBS port. The following values instruct the port to use corresponding bonding scheme if supported: none(0) - instructs the port not to use bonding (only on single-BCE G.998.2 GBS) g9981(1) - instructs the port to use G.998.1 bonding g9982(2) - instructs the port to use G.998.2 bonding g9983(3) - instructs the port to use G.998.3 bonding Changing of gBondPortConfAdminScheme MUST be performed when the link is administratively 'down', as indicated by the ifAdminStatus object in IF-MIB. Attempts to change this object MUST be rejected (in case of SNMP with the error inconsistentValue), if the link is Up or Initializing. Attempts to change this object to an unsupported bonding scheme (see gBondPortCapSchemesSupported) SHALL be rejected (in case of SNMP with the error wrongValue). Setting this object to the value of 'none' must be rejected for Beili & Morgenstern Expires January 17, 2013 [Page 26] Internet-Draft G.Bond MIB Jul 2012 GBS ports with multiple BCEs (with the error inconsistentValue). This object maps to the TR-159 attribute aGroupAdminBondScheme." REFERENCE "[TR-159] 5.5.1.6; IF-MIB, ifAdminStatus" ::= { gBondPortConfEntry 1 } gBondPortConfPeerAdminScheme OBJECT-TYPE SYNTAX IANAgBondScheme MAX-ACCESS read-write STATUS current DESCRIPTION "A desired bonding scheme for a peer (link partner) G.Bond port (GBS). The following values instruct the peer port to use corresponding bonding scheme if supported: none(0) - instructs the port not to use bonding (only on single-BCE G.998.2 GBS) g9981(1) - instructs the port to use G.998.1 bonding g9982(2) - instructs the port to use G.998.2 bonding g9983(3) - instructs the port to use G.998.3 bonding Changing of this object MUST be performed when the link is administratively 'down', as indicated by the ifAdminStatus object in IF-MIB. Attempts to change this object MUST be rejected (in case of SNMP with the error inconsistentValue), if the link is Up or Initializing. Attempts to change this object to an unsupported bonding scheme (see gBondPortCapPeerSchemesSupported) SHALL be rejected (in case of SNMP with the error wrongValue). Setting this object to the value of 'none' must be rejected for GBS ports with multiple BCEs (with the error inconsistentValue). This object maps to the TR-159 attribute aGroupPeerAdminBondScheme." REFERENCE "[TR-159] 5.5.1.7; IF-MIB, ifAdminStatus" ::= { gBondPortConfEntry 2 } gBondPortConfDiscoveryCode OBJECT-TYPE SYNTAX PhysAddress (SIZE(6)) MAX-ACCESS read-write STATUS current DESCRIPTION "A Discovery Code of the G.Bond port (GBS). A unique 6 octet long code used by the Discovery function. This object MUST be instantiated for the -O subtype GBS before writing operations on the gBondBceConfRemoteDiscoveryCode Beili & Morgenstern Expires January 17, 2013 [Page 27] Internet-Draft G.Bond MIB Jul 2012 (Set_if_Clear and Clear_if_Same) are performed by BCEs associated with the GBS. The initial value of this object for -R subtype ports after reset is all zeroes. For -R subtype ports, the value of this object cannot be changed directly. This value may be changed as a result of writing operation on the gBondBceConfRemoteDiscoveryCode object of remote BCE of -O subtype, connected to one of the local BCEs associated with the GBS. Discovery MUST be performed when the link is administratively 'down', as indicated by the ifAdminStatus object in IF-MIB. Attempts to change this object MUST be rejected (in case of SNMP with the error inconsistentValue), if the link is Up or Initializing. This object maps to the TR-159 attribute aGroupDiscoveryCode." REFERENCE "[TR-159] 5.5.1.20; [802.3] 61.2.2.8.3, 61.2.2.8.4, 45.2.6.6.1, 45.2.6.8, 61A.2; IF-MIB, ifAdminStatus" ::= { gBondPortConfEntry 3 } gBondPortConfTargetUpDataRate OBJECT-TYPE SYNTAX Unsigned32(0|1..10000000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "A desired G.Bond port Data Rate in the upstream direction, in Kbps, to be achieved during initialization, under restrictions placed upon the member BCEs by their respective configuration settings. This object represents a sum of individual BCE upstream data rates, modified to compensate for fragmentation and encapsulation overhead (e.g., for an Ethernet service, the target data rate of 10Mbps SHALL allow lossless transmission of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap). Note that the target upstream data rate may not be achieved during initialization (e.g., due to unavailability of required BCEs) or the initial bandwidth could deteriorate, so that the actual upstream data rate (gBondPortStatUpDataRate) could be less than gBondPortConfTargetUpDataRate. The value is limited above by 10 Gbps, to accommodate very high speed bonded xDSL interfaces (e.g. 32 x 100Mbps). Beili & Morgenstern Expires January 17, 2013 [Page 28] Internet-Draft G.Bond MIB Jul 2012 The value between 1 and 10000000 indicates that the total upstream data rate of the G.Bond port after initialization SHALL be equal to the target data rate or less, if the target upstream data rate cannot be achieved under the restrictions configured for BCEs. In case the copper environment allows to achieve higher upstream data rate than that specified by this object, the excess capability SHALL be either converted to additional SNR margin or reclaimed by minimizing transmit power. The value of 0 means that the target data rate is not fixed and SHALL be set to the maximum attainable rate during initialization (Best Effort), under specified spectral restrictions and with desired SNR Margin per BCE. This object is read-write for the -O subtype G.Bond ports. It is irrelevant for the -R subtypes - attempts to read or change this object for such ports MUST be rejected (in case of SNMP with the error inconsistentValue). Changing of the Target Upstream Data Rate MUST be performed when the link is administratively 'down', as indicated by the ifAdminStatus object in IF-MIB. Attempts to change this object MUST be rejected (in case of SNMP with the error inconsistentValue), if the link is Up or Initializing. This object maps to the TR-159 attribute aGroupTargetUpRate." REFERENCE "[TR-159] 5.5.1.17; IF-MIB, ifAdminStatus" ::= { gBondPortConfEntry 4 } gBondPortConfTargetDnDataRate OBJECT-TYPE SYNTAX Unsigned32(0|1..10000000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "A desired G.Bond port Data Rate in the downstream direction, in Kbps, to be achieved during initialization, under restrictions placed upon the member BCEs by their respective configuration settings. This object represents a sum of individual BCE downstream data rates, modified to compensate for fragmentation and encapsulation overhead (e.g., for an Ethernet service, the target data rate of 10Mbps SHALL allow lossless transmission of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap). Beili & Morgenstern Expires January 17, 2013 [Page 29] Internet-Draft G.Bond MIB Jul 2012 Note that the target downstream data rate may not be achieved during initialization (e.g., due to unavailability of required BCEs) or the initial bandwidth could deteriorate, so that the actual downstream data rate (gBondPortStatDnDataRate) could be less than gBondPortConfTargetDnDataRate. The value is limited above by 10 Gbps, to accommodate very high speed bonded xDSL interfaces (e.g. 32 x 100Mbps). The value between 1 and 10000000 indicates that the total downstream data rate of the G.Bond port after initialization SHALL be equal to the target data rate or less, if the target downstream data rate cannot be achieved under the restrictions configured for BCEs. In case the copper environment allows to achieve higher downstream data rate than that specified by this object, the excess capability SHALL be either converted to additional SNR margin or reclaimed by minimizing transmit power. The value of 0 means that the target data rate is not fixed and SHALL be set to the maximum attainable rate during initialization (Best Effort), under specified spectral restrictions and with desired SNR Margin per BCE. This object is read-write for the -O subtype G.Bond ports. It is irrelevant for the -R subtypes - attempts to read or change this object for such ports MUST be rejected (in case of SNMP with the error inconsistentValue). Changing of the Target Downstream Data Rate MUST be performed when the link is administratively 'down', as indicated by the ifAdminStatus object in IF-MIB. Attempts to change this object MUST be rejected (in case of SNMP with the error inconsistentValue), if the link is Up or Initializing. This object maps to the TR-159 attribute aGroupTargetDownRate." REFERENCE "[TR-159] 5.5.1.18; IF-MIB, ifAdminStatus" ::= { gBondPortConfEntry 5 } gBondPortConfThreshLowUpRate OBJECT-TYPE SYNTAX Unsigned32(1..10000000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the G.Bond port low upstream rate Beili & Morgenstern Expires January 17, 2013 [Page 30] Internet-Draft G.Bond MIB Jul 2012 crossing alarm threshold. When the current value of gBondPortStatUpDataRate for this port reaches/drops below or exceeds this threshold, a gBondLowUpRateCrossing notification MAY be generated if enabled by gBondPortConfLowRateCrossingEnable. This object is read-write for the -O subtype G.Bond ports. It is irrelevant for the -R subtypes - attempts to read or change this object for such ports MUST be rejected (in case of SNMP with the error inconsistentValue). This object maps to the TR-159 attribute aGroupthreshLowUpRate." REFERENCE "[TR-159] 5.5.1.21" ::= { gBondPortConfEntry 6 } gBondPortConfThreshLowDnRate OBJECT-TYPE SYNTAX Unsigned32(1..10000000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the G.Bond port low downstream rate crossing alarm threshold. When the current value of gBondPortStatDnDataRate for this port reaches/drops below or exceeds this threshold, a gBondLowDnRateCrossing notification MAY be generated if enabled by gBondPortConfLowRateCrossingEnable. This object is read-write for the -O subtype G.Bond ports. It is irrelevant for the -R subtypes - attempts to read or change this object for such ports MUST be rejected (in case of SNMP with the error inconsistentValue). This object maps to the TR-159 attribute aGroupThreshDownUpRate." REFERENCE "[TR-159] 5.5.1.22" ::= { gBondPortConfEntry 7 } gBondPortConfLowRateCrossingEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether gBondLowUpRateCrossing and gBondLowDnRateCrossing notifications should be generated Beili & Morgenstern Expires January 17, 2013 [Page 31] Internet-Draft G.Bond MIB Jul 2012 for this interface. Value of true(1) indicates that the notifications are enabled. Value of false(2) indicates that the notifications are disabled. This object is read-write for the -O subtype G.Bond ports. It is irrelevant for the -R subtypes - attempts to read or change this object for such ports MUST be rejected (in case of SNMP with the error inconsistentValue). This object maps to the TR-159 attribute aGroupLowRateCrossingEnable." REFERENCE "[TR-159] 5.5.1.23" ::= { gBondPortConfEntry 8 } gBondPortConfPmTcaConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the index of the row in the GBS port Alarm Configuration Profile Table for Performance Monitoring Threshold Crossing Alerts - gBondPortAlarmConfProfileTable, which applies to this GBS port." DEFVAL { "DEFVAL" } ::= { gBondPortConfEntry 9 } gBondPortConfPmTcaEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether gBondPerfTca*Crossing set of notifications should be generated for this interface. Value of true(1) indicates that the notifications are enabled. Value of false(2) indicates that the notifications are disabled. This object maps to the TR-159 attribute aGroupPerfTcaEnable." REFERENCE "[TR-159] 5.5.1.38" ::= { gBondPortConfEntry 10 } gBondPortCapTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortCapEntry Beili & Morgenstern Expires January 17, 2013 [Page 32] Internet-Draft G.Bond MIB Jul 2012 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for capabilities of G.Bond Ports. Entries in this table MUST be maintained in a persistent manner" ::= { gBondPort 2 } gBondPortCapEntry OBJECT-TYPE SYNTAX GBondPortCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond Port Capability table. Each entry represents a G.Bond port indexed by the ifIndex. Note that a G.Bond GBS port runs on top of a single or multiple BCE port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { gBondPortCapTable 1 } GBondPortCapEntry ::= SEQUENCE { gBondPortCapSchemesSupported IANAgBondSchemeList, gBondPortCapPeerSchemesSupported IANAgBondSchemeList, gBondPortCapCapacity Unsigned32, gBondPortCapPeerCapacity Unsigned32 } gBondPortCapSchemesSupported OBJECT-TYPE SYNTAX IANAgBondSchemeList MAX-ACCESS read-only STATUS current DESCRIPTION "Bonding Capability of the G.Bond port (GBS). This is a read-only bitmap of the possible bonding schemes supported by the GBS. The various bit-positions are: none(0) - GBS is capable of bonding bypass on a single-BCE (G.998.2 only) g9981(1) - GBS is capable of G.998.1 bonding g9982(2) - GBS is capable of G.998.2 bonding g9983(3) - GBS is capable of G.998.3 bonding Note that for ports supporting multiple bonding schemes the actual administrative scheme is set via gBondPortConfAdminScheme object. The current operating bonding scheme is reflected in the gBondPortStatOperScheme. This object maps to the TR-159 attribute aGroupBondSchemesSupported." Beili & Morgenstern Expires January 17, 2013 [Page 33] Internet-Draft G.Bond MIB Jul 2012 REFERENCE "[TR-159] 5.5.1.2" ::= { gBondPortCapEntry 1 } gBondPortCapPeerSchemesSupported OBJECT-TYPE SYNTAX IANAgBondSchemeList MAX-ACCESS read-only STATUS current DESCRIPTION "Bonding Capability of the peer G.Bond port (GBS). This is a read-only bitmap of the possible bonding schemes supported by the link partner GBS. The various bit-positions are: none(0) - peer GBS does not support bonding or the peer unit could not be reached or peer GBS is capable of bonding bypass on a single-BCE (G.998.2 only) g9981(1) - peer GBS is capable of G.998.1 bonding g9982(2) - peer GBS is capable of G.998.2 bonding g9983(3) - peer GBS is capable of G.998.3 bonding Note that for ports supporting multiple bonding schemes the actual administrative scheme is set via gBondPortConfPeerAdminScheme object. The current operating bonding scheme is reflected in the gBondPortStatPeerOperScheme. This object maps to the TR-159 attribute aGroupBondPeerSchemesSupported." REFERENCE "[TR-159] 5.5.1.3" ::= { gBondPortCapEntry 2 } gBondPortCapCapacity OBJECT-TYPE SYNTAX Unsigned32 (1..32) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of BCEs that can be aggregated by the local GBS. The number of BCEs currently assigned to a particular G.Bond port (gBondPortStatNumBCEs) is never greater than gBondPortCapCapacity. This object maps to the TR-159 attribute aGroupCapacity." REFERENCE "[TR-159] 5.5.1.12" ::= { gBondPortCapEntry 3 } gBondPortCapPeerCapacity OBJECT-TYPE SYNTAX Unsigned32 (0|1..32) Beili & Morgenstern Expires January 17, 2013 [Page 34] Internet-Draft G.Bond MIB Jul 2012 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of BCEs that can be aggregated by the peer GBS port. Value of 0 is returned when peer Bonding Capacity is unknown (peer cannot be reached). This object maps to the TR-159 attribute aGroupPeerCapacity." REFERENCE "[TR-159] 5.5.1.13" ::= { gBondPortCapEntry 4 } gBondPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides overall status information of G.Bond ports, complementing the generic status information from the ifTable of IF-MIB. Additional status information about connected BCEs is available from the relevant line MIBs This table contains live data from the equipment. As such, it is NOT persistent." ::= { gBondPort 3 } gBondPortStatEntry OBJECT-TYPE SYNTAX GBondPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond Port Status table. Each entry represents a G.Bond port indexed by the ifIndex. Note that a G.Bond GBS port runs on top of a single or multiple BCE port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { gBondPortStatTable 1 } GBondPortStatEntry ::= SEQUENCE { gBondPortStatOperScheme IANAgBondScheme, gBondPortStatPeerOperScheme IANAgBondScheme, gBondPortStatUpDataRate Gauge32, gBondPortStatDnDataRate Gauge32, gBondPortStatFltStatus BITS, gBondPortStatSide INTEGER, gBondPortStatNumBCEs Unsigned32 Beili & Morgenstern Expires January 17, 2013 [Page 35] Internet-Draft G.Bond MIB Jul 2012 } gBondPortStatOperScheme OBJECT-TYPE SYNTAX IANAgBondScheme MAX-ACCESS read-only STATUS current DESCRIPTION "Current operating bonding scheme of a G.Bond port. The possible values are: none(0) - bonding bypass on a single-BCE (G.998.2 only) g9981(1) - G.998.1 bonding g9982(2) - G.998.2 bonding g9983(3) - G.998.3 bonding This object maps to the TR-159 attribute aGroupOperBondScheme." REFERENCE "[TR-159] 5.5.1.4" ::= { gBondPortStatEntry 1 } gBondPortStatPeerOperScheme OBJECT-TYPE SYNTAX IANAgBondScheme MAX-ACCESS read-only STATUS current DESCRIPTION "Current operating bonding scheme of a G.Bond port link partner. The possible values are: unknown(0) - peer cannot be reached due to the link state or bonding bypass on a single-BCE (G.998.2 only) g9981(1) - G.998.1 bonding g9982(2) - G.998.2 bonding g9983(3) - G.998.3 bonding This object maps to the TR-159 attribute aGroupPeerOperBondScheme." REFERENCE "[TR-159] 5.5.1.5" ::= { gBondPortStatEntry 2 } gBondPortStatUpDataRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "A current G.Bond port operational Data Rate in the upstream direction, in bps. This object represents an estimation of the sum of individual Beili & Morgenstern Expires January 17, 2013 [Page 36] Internet-Draft G.Bond MIB Jul 2012 BCE upstream data rates, modified to compensate for fragmentation and encapsulation overhead (e.g., for an Ethernet service, the target data rate of 10Mbps SHALL allow lossless transmission of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap). Note that for symmetrical interfaces gBondPortStatUpDataRate == gBondPortStatDnDataRate == ifSpeed. This object maps to the TR-159 attribute aGroupUpRate." REFERENCE "[TR-159] 5.5.1.15" ::= { gBondPortStatEntry 3 } gBondPortStatDnDataRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "A current G.Bond port operational Data Rate in the downstream direction, in bps. This object represents an estimation of the sum of individual BCE downstream data rates, modified to compensate for fragmentation and encapsulation overhead (e.g., for an Ethernet service, the target data rate of 10Mbps SHALL allow lossless transmission of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap). Note that for symmetrical interfaces gBondPortStatUpDataRate == gBondPortStatDnDataRate == ifSpeed. This object maps to the TR-159 attribute aGroupDownRate." REFERENCE "[TR-159] 5.5.1.16" ::= { gBondPortStatEntry 4 } gBondPortStatFltStatus OBJECT-TYPE SYNTAX BITS { noPeer(0), peerPowerLoss(1), peerBondSchemeMismatch(2), bceSubTypeMismatch(3), lowRate(4), init(5), ready(6) } Beili & Morgenstern Expires January 17, 2013 [Page 37] Internet-Draft G.Bond MIB Jul 2012 MAX-ACCESS read-only STATUS current DESCRIPTION "G.Bond (GBS) port Fault Status. This is a bitmap of possible conditions. The various bit positions are: noPeer - peer GBS cannot be reached (e.g., no BCEs attached, all BCEs are Down etc.). peerPowerLoss - peer GBS has indicated impending unit failure due to loss of local power ('Dying Gasp'). peerBondSchemeMismatch - operating bonding scheme of a peer GBS is different from the local one. bceSubTypeMismatch - local BCEs in the aggregation group are not of the same sub-type, e.g., some BCEs in the local device are -O while others are -R subtype. lowRate - gBondUpRate/gBondDnRate of the port has reached or dropped below gBondPortConfThreshLowUpRate/ gBondPortConfThreshLowDnRate. init - The link is Initializing, as a result of ifAdminStatus being set to 'up' for a particular BCE or a GBS to which the BCE is connected. ready - at least one BCE in the aggregation group is detecting handshake tones. This object is intended to supplement ifOperStatus object in IF-MIB. This object maps to the TR-159 attribute aGroupStatus." REFERENCE "[TR-159] 5.5.1.9; IF-MIB, ifOperStatus" ::= { gBondPortStatEntry 5 } gBondPortStatSide OBJECT-TYPE SYNTAX INTEGER { subscriber(1), office(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "G.Bond port mode of operation (subtype). The value of 'subscriber' indicates the port is designated as '-R' subtype (all BCEs assigned to this port are of subtype Beili & Morgenstern Expires January 17, 2013 [Page 38] Internet-Draft G.Bond MIB Jul 2012 '-R'). The value of the 'office' indicates that the port is designated as '-O' subtype (all BCEs assigned to this port are of subtype '-O'). The value of 'unknown' indicates that the port has no assigned BCEs yet or that the assigned BCEs are not of the same side (subTypeBCEMismatch). This object maps to the TR-159 attribute aGroupEnd." REFERENCE "[TR-159] 5.5.1.11" ::= { gBondPortStatEntry 6 } gBondPortStatNumBCEs OBJECT-TYPE SYNTAX Unsigned32 (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of BCEs that is currently aggregated by the local GBS (assigned to the G.Bond port using ifStackTable). This number is never greater than gBondPortCapCapacity. This object SHALL be automatically incremented or decremented when a BCE is added or deleted to/from the G.Bond port using ifStackTable. This object maps to the TR-159 attribute aGroupNumChannels" REFERENCE "[TR-159] 5.5.1.14" ::= { gBondPortStatEntry 7 } -- Performance Monitoring group gBondPortPM OBJECT IDENTIFIER ::= { gBondPort 4 } gBondPortPmCurTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains current Performance Monitoring (PM) information for a GBS port. This table contains live data from the equipment and as such is NOT persistent." ::= { gBondPortPM 1 } gBondPortPmCurEntry OBJECT-TYPE SYNTAX GBondPortPmCurEntry Beili & Morgenstern Expires January 17, 2013 [Page 39] Internet-Draft G.Bond MIB Jul 2012 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond Port PM table. Each entry represents a G.Bond port indexed by the ifIndex. Note that a G.Bond GBS port runs on top of a single or multiple BCE port(s), which are also indexed by ifIndex." INDEX { ifIndex } ::= { gBondPortPmCurTable 1 } GBondPortPmCurEntry ::= SEQUENCE { gBondPortPmCurES HCPerfTotalCount, gBondPortPmCurSES HCPerfTotalCount, gBondPortPmCurUAS HCPerfTotalCount, gBondPortPmCur15MinValidIntervals HCPerfValidIntervals, gBondPortPmCur15MinInvalidIntervals HCPerfInvalidIntervals, gBondPortPmCur15MinTimeElapsed HCPerfTimeElapsed, gBondPortPmCur15MinES HCPerfCurrentCount, gBondPortPmCur15MinSES HCPerfCurrentCount, gBondPortPmCur15MinUAS HCPerfCurrentCount, gBondPortPmCur1DayValidIntervals Unsigned32, gBondPortPmCur1DayInvalidIntervals Unsigned32, gBondPortPmCur1DayTimeElapsed HCPerfTimeElapsed, gBondPortPmCur1DayES HCPerfCurrentCount, gBondPortPmCur1DaySES HCPerfCurrentCount, gBondPortPmCur1DayUAS HCPerfCurrentCount } gBondPortPmCurES OBJECT-TYPE SYNTAX HCPerfTotalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Errored Seconds (ES) on the GBS since the BTU was last restarted. An Errored Second for a G.998.x interface is defined as a count of 1-second intervals during which one or more GBS errors are declared. The errors are specific for each bonding scheme, e.g. - lost cells for the ATM bonding; - lost or discarded (due to an error or a buffer overflow) fragments for the Ethernet bonding; - CRC4, CRC6 or CRC8 errors for the TDIM bonding This object is inhibited during Unavailable Seconds (UAS). This object maps to the TR-159 attribute aGroupPerfES." Beili & Morgenstern Expires January 17, 2013 [Page 40] Internet-Draft G.Bond MIB Jul 2012 REFERENCE "[TR-159] 5.5.1.29" ::= { gBondPortPmCurEntry 1 } gBondPortPmCurSES OBJECT-TYPE SYNTAX HCPerfTotalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Severely Errored Seconds (SES) on the GBS since the BTU was last restarted. A Severely Errored Second for a G.998.x interface is defined as a count of 1-second intervals during which GBS errors cause at least 1% traffic loss of the nominal bonded link rate or at least 12ms for the TDM traffic. The exact definition is specific for each bonding scheme, e.g. - 234 lost cells for the ATM bonding with 10Mbps nominal link rate - 60 lost/discarded fragments for the Ethernet bonding with 10Mbps nominal link rate and fixed 192 Byte-long fragment size. - 6 or more CRC4, one or more CRC6 or one or more CRC8 errors for the TDM bonding This object is inhibited during Unavailable Seconds (UAS). This object maps to the TR-159 attribute aGroupPerfSES." REFERENCE "[TR-159] 5.5.1.30" ::= { gBondPortPmCurEntry 2 } gBondPortPmCurUAS OBJECT-TYPE SYNTAX HCPerfTotalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Unavailable Seconds (UAS) on the GBS since the BTU was last restarted. An Unavailable Second for a G.998.x interface is defined as a count of 1-second intervals during which the bonded link is unavailable. The G.998.x link becomes unavailable at the onset of 10 contiguous SESs. The 10 SESs are included in the unavailable time. Once unavailable, the G.998.x line becomes available at the onset of 10 contiguous seconds with no SESs. The 10 seconds with no SESs are excluded from unavailable time. Beili & Morgenstern Expires January 17, 2013 [Page 41] Internet-Draft G.Bond MIB Jul 2012 This object maps to the TR-159 attribute aGroupPerfUAS." REFERENCE "[TR-159] 5.5.1.31" ::= { gBondPortPmCurEntry 3 } gBondPortPmCur15MinValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A number of 15-minute intervals for which data was collected. The value of this object will be 96 or the maximum number of 15-minute history intervals collected by the implementation unless the measurement was (re-)started recently, in which case the value will be the number of complete 15 minutes intervals for which there are at least some data. In certain cases it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available. This object maps to the TR-159 attribute aGroupPerf15MinValidIntervals." REFERENCE "[TR-159] 5.5.1.32" ::= { gBondPortPmCurEntry 4 } gBondPortPmCur15MinInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A number of 15-minute intervals for which data was not always available. The value will typically be zero except in cases where the data for some intervals are not available. This object maps to the TR-159 attribute aGroupPerf15MinInvalidIntervals." REFERENCE "[TR-159] 5.5.1.33" ::= { gBondPortPmCurEntry 5 } gBondPortPmCur15MinTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of seconds that have elapsed since the beginning of the Beili & Morgenstern Expires January 17, 2013 [Page 42] Internet-Draft G.Bond MIB Jul 2012 current 15-minute performance interval. This object maps to the TR-159 attribute aGroupPerfCurr15MinTimeElapsed." REFERENCE "[TR-159] 5.5.1.34" ::= { gBondPortPmCurEntry 6 } gBondPortPmCur15MinES OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Errored Seconds (ES) on the GBS in the current 15-minute performance interval. This object maps to the TR-159 attribute aGroupPerfCurr15MinES." REFERENCE "[TR-159] 5.5.1.35" ::= { gBondPortPmCurEntry 7 } gBondPortPmCur15MinSES OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Severely Errored Seconds (ES) on the GBS in the current 15-minute performance interval. This object maps to the TR-159 attribute aGroupPerfCurr15MinSES." REFERENCE "[TR-159] 5.5.1.36" ::= { gBondPortPmCurEntry 8 } gBondPortPmCur15MinUAS OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Unavailable Seconds (UAS) on the GBS in the current 15-minute performance interval. This object maps to the TR-159 attribute aGroupPerfCurr15MinUAS." REFERENCE "[TR-159] 5.5.1.37" Beili & Morgenstern Expires January 17, 2013 [Page 43] Internet-Draft G.Bond MIB Jul 2012 ::= { gBondPortPmCurEntry 9 } gBondPortPmCur1DayValidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "A number of 1-day intervals for which data was collected. The value of this object will be 7 or the maximum number of 1-day history intervals collected by the implementation unless the measurement was (re-)started recently, in which case the value will be the number of complete 1-day intervals for which there are at least some data. In certain cases it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available. This object maps to the TR-159 attribute aGroupPerf1DayValidIntervals." REFERENCE "[TR-159] 5.5.1.45" ::= { gBondPortPmCurEntry 10 } gBondPortPmCur1DayInvalidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "A number of 1-day intervals for which data was not always available. The value will typically be zero except in cases where the data for some intervals are not available. This object maps to the TR-159 attribute aGroupPerf1DayInvalidIntervals." REFERENCE "[TR-159] 5.5.1.46" ::= { gBondPortPmCurEntry 11 } gBondPortPmCur1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of seconds that have elapsed since the beginning of the current 1-day performance interval. Beili & Morgenstern Expires January 17, 2013 [Page 44] Internet-Draft G.Bond MIB Jul 2012 This object maps to the TR-159 attribute aGroupPerfCurr1DayTimeElapsed." REFERENCE "[TR-159] 5.5.1.47" ::= { gBondPortPmCurEntry 12 } gBondPortPmCur1DayES OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Errored Seconds (ES) on the GBS in the current 1-day performance interval. This object maps to the TR-159 attribute aGroupPerfCurr1DayES." REFERENCE "[TR-159] 5.5.1.48" ::= { gBondPortPmCurEntry 13 } gBondPortPmCur1DaySES OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Severely Errored Seconds (ES) on the GBS in the current 1-day performance interval. This object maps to the TR-159 attribute aGroupPerfCurr1DaySES." REFERENCE "[TR-159] 5.5.1.49" ::= { gBondPortPmCurEntry 14 } gBondPortPmCur1DayUAS OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Unavailable Seconds (UAS) on the GBS in the current 1-day performance interval. This object maps to the TR-159 attribute aGroupPerfCurr1DayUAS." REFERENCE "[TR-159] 5.5.1.50" ::= { gBondPortPmCurEntry 15 } Beili & Morgenstern Expires January 17, 2013 [Page 45] Internet-Draft G.Bond MIB Jul 2012 -- PM history: 15-min buckets gBondPortPm15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 15-minute buckets of Performance Monitoring information for a GBS port (a row for each 15-minute interval, up to 96 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { gBondPortPM 2 } gBondPortPm15MinEntry OBJECT-TYPE SYNTAX GBondPortPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond Port historical 15-minute PM table. Each entry represents performance monitoring data for a GBS port, indexed by ifIndex, collected during a particular 15-minute interval, indexed by gBondPortPm15MinIntervalIndex." INDEX { ifIndex, gBondPortPm15MinIntervalIndex } ::= { gBondPortPm15MinTable 1 } GBondPortPm15MinEntry ::= SEQUENCE { gBondPortPm15MinIntervalIndex Unsigned32, gBondPortPm15MinIntervalMoniTime HCPerfTimeElapsed, gBondPortPm15MinIntervalES HCPerfIntervalCount, gBondPortPm15MinIntervalSES HCPerfIntervalCount, gBondPortPm15MinIntervalUAS HCPerfIntervalCount, gBondPortPm15MinIntervalValid TruthValue } gBondPortPm15MinIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are OPTIONAL. This object maps to the TR-159 attribute aGroupPerf15MinIntervalNumber." REFERENCE "[TR-159] 5.5.1.57" Beili & Morgenstern Expires January 17, 2013 [Page 46] Internet-Draft G.Bond MIB Jul 2012 ::= { gBondPortPm15MinEntry 1 } gBondPortPm15MinIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (900 seconds), except in a situation where performance data could not be collected for any reason." ::= { gBondPortPm15MinEntry 2 } gBondPortPm15MinIntervalES OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Errored Seconds (ES) on the GBS in the 15-minute performance history interval. This object maps to the TR-159 attribute aGroupPerf15MinIntervalES." REFERENCE "[TR-159] 5.5.1.59" ::= { gBondPortPm15MinEntry 3 } gBondPortPm15MinIntervalSES OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Severely Errored Seconds (ES) on the GBS in the 15-minute performance history interval. This object maps to the TR-159 attribute aGroupPerf15MinIntervalSES." REFERENCE "[TR-159] 5.5.1.60" ::= { gBondPortPm15MinEntry 4 } gBondPortPm15MinIntervalUAS OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only Beili & Morgenstern Expires January 17, 2013 [Page 47] Internet-Draft G.Bond MIB Jul 2012 STATUS current DESCRIPTION "A count of Unavailable Seconds (UAS) on the GBS in the current 15-minute performance interval. This object maps to the TR-159 attribute aGroupPerfCurr15MinUAS." REFERENCE "[TR-159] 5.5.1.61" ::= { gBondPortPm15MinEntry 5 } gBondPortPm15MinIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. Valid bucket is reported as true(1) and invalid bucket as false(2). If this history bucket is invalid the BTU-C MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its data base. In such case this object is not required as only valid history buckets are available while invalid history buckets are simply not in the data base. This object maps to the TR-159 attribute aGroupPerf15MinIntervalValid." REFERENCE "[TR-159] 5.5.1.58" ::= { gBondPortPm15MinEntry 6 } -- PM history: 1-day buckets gBondPortPm1DayTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 1-day buckets of Performance Monitoring information for a GBS port (a row for each 1-day interval, up to 7 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { gBondPortPM 3 } gBondPortPm1DayEntry OBJECT-TYPE SYNTAX GBondPortPm1DayEntry MAX-ACCESS not-accessible Beili & Morgenstern Expires January 17, 2013 [Page 48] Internet-Draft G.Bond MIB Jul 2012 STATUS current DESCRIPTION "An entry in the G.Bond Port historical 1-day PM table. Each entry represents performance monitoring data for a GBS port, indexed by ifIndex, collected during a particular 1-day interval, indexed by gBondPortPm1DayIntervalIndex." INDEX { ifIndex, gBondPortPm1DayIntervalIndex } ::= { gBondPortPm1DayTable 1 } GBondPortPm1DayEntry ::= SEQUENCE { gBondPortPm1DayIntervalIndex Unsigned32, gBondPortPm1DayIntervalMoniTime HCPerfTimeElapsed, gBondPortPm1DayIntervalES HCPerfIntervalCount, gBondPortPm1DayIntervalSES HCPerfIntervalCount, gBondPortPm1DayIntervalUAS HCPerfIntervalCount, gBondPortPm1DayIntervalValid TruthValue } gBondPortPm1DayIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the most recent previous interval; interval 7 is 7 days ago. Intervals 2..7 are OPTIONAL. This object maps to the TR-159 attribute aGroupPerf1DayIntervalNumber." REFERENCE "[TR-159] 5.5.1.62" ::= { gBondPortPm1DayEntry 1 } gBondPortPm1DayIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (86400 seconds), except in a situation where performance data could not be collected for any reason. This object maps to the TR-159 attribute aGroupPerf1DayIntervalMoniSecs." REFERENCE Beili & Morgenstern Expires January 17, 2013 [Page 49] Internet-Draft G.Bond MIB Jul 2012 "[TR-159] 5.5.1.64" ::= { gBondPortPm1DayEntry 2 } gBondPortPm1DayIntervalES OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Errored Seconds (ES) on the GBS in the 1-day performance history interval. This object maps to the TR-159 attribute aGroupPerf1DayIntervalES." REFERENCE "[TR-159] 5.5.1.65" ::= { gBondPortPm1DayEntry 3 } gBondPortPm1DayIntervalSES OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Severely Errored Seconds (ES) on the GBS in the 1-day performance history interval. This object maps to the TR-159 attribute aGroupPerf1DayIntervalSES." REFERENCE "[TR-159] 5.5.1.66" ::= { gBondPortPm1DayEntry 4 } gBondPortPm1DayIntervalUAS OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of Unavailable Seconds (UAS) on the GBS in the current 1-day performance interval. This object maps to the TR-159 attribute aGroupPerfCurr1DayUAS." REFERENCE "[TR-159] 5.5.1.67" ::= { gBondPortPm1DayEntry 5 } gBondPortPm1DayIntervalValid OBJECT-TYPE Beili & Morgenstern Expires January 17, 2013 [Page 50] Internet-Draft G.Bond MIB Jul 2012 SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. Valid bucket is reported as true(1) and invalid bucket as false(2). If this history bucket is invalid the BTU-C MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its data base. In such case this object is not required as only valid history buckets are available while invalid history buckets are simply not in the data base. This object maps to the TR-159 attribute aGroupPerf1DayIntervalValid." REFERENCE "[TR-159] 5.5.1.63" ::= { gBondPortPm1DayEntry 6 } -- Performance Monitoring TCA Configuration profile gBondPortPmTcaProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondPortPmTcaProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table supports definitions of Performance Monitoring (PM) Threshold Crossing Alerts (TCA) configuration profiles for GBS ports. Entries in this table MUST be maintained in a persistent manner." ::= { gBondPortPM 4 } gBondPortPmTcaProfileEntry OBJECT-TYPE SYNTAX GBondPortPmTcaProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the GBS PM TCA Configuration table. Each entry corresponds to a single TCA configuration profile. Each profile contains a set of parameters for setting alarm thresholds for various performance attributes monitored at GBS ports. Profiles may be created/deleted using the row creation/deletion mechanism via gBondPortPmTcaProfileRowStatus. If an active entry is referenced via gBondPortConfPmTcaConfProfile, the entry MUST Beili & Morgenstern Expires January 17, 2013 [Page 51] Internet-Draft G.Bond MIB Jul 2012 remain active until all references are removed. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document." INDEX { gBondPortPmTcaProfileName } ::= { gBondPortPmTcaProfileTable 1 } GBondPortPmTcaProfileEntry ::= SEQUENCE { gBondPortPmTcaProfileName SnmpAdminString, gBondPortPmTcaProfileThresh15MinES HCPerfIntervalThreshold, gBondPortPmTcaProfileThresh15MinSES HCPerfIntervalThreshold, gBondPortPmTcaProfileThresh15MinUAS HCPerfIntervalThreshold, gBondPortPmTcaProfileThresh1DayES GBondPm1DayIntervalThreshold, gBondPortPmTcaProfileThresh1DaySES GBondPm1DayIntervalThreshold, gBondPortPmTcaProfileThresh1DayUAS GBondPm1DayIntervalThreshold, gBondPortPmTcaProfileRowStatus RowStatus } gBondPortPmTcaProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is a unique index (name) associated with this GBS PM TCA profile." ::= { gBondPortPmTcaProfileEntry 1 } gBondPortPmTcaProfileThresh15MinES OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A desired threshold for the number of Errored Seconds (ES) within any given 15-minute performance data collection interval. If the number of ESs in a particular 15-minute collection interval reaches or exceeds this value, a gBondPmTca15MinESCrossing notification MAY be generated if enabled by gBondPortConfPmTcaEnable. At most one notification can be sent per interval. Setting this attribute to zero (default) effectively disables gBondPmTca15MinESCrossing notification. This object maps to the TR-159 attribute aGroupPerfThreshold15MinES." REFERENCE "[TR-159] 5.5.1.39" Beili & Morgenstern Expires January 17, 2013 [Page 52] Internet-Draft G.Bond MIB Jul 2012 ::= { gBondPortPmTcaProfileEntry 2 } gBondPortPmTcaProfileThresh15MinSES OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A desired threshold for the number of Severely Errored Seconds (SES) within any given 15-minute performance data collection interval. If the number of SESs in a particular 15-minute collection interval reaches or exceeds this value, a gBondPmTca15MinSESCrossing notification MAY be generated if enabled by gBondPortConfPmTcaEnable. At most one notification can be sent per interval. Setting this attribute to zero (default) effectively disables gBondPmTca15MinSESCrossing notification. This object maps to the TR-159 attribute aGroupPerfThreshold15MinSES." REFERENCE "[TR-159] 5.5.1.40" ::= { gBondPortPmTcaProfileEntry 3 } gBondPortPmTcaProfileThresh15MinUAS OBJECT-TYPE SYNTAX HCPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A desired threshold for the number of Unavailable Seconds (UAS) within any given 15-minute performance data collection interval. If the number of UASs in a particular 15-minute collection interval reaches or exceeds this value, a gBondPmTca15MinUASCrossing notification MAY be generated if enabled by gBondPortConfPmTcaEnable. At most one notification can be sent per interval. Setting this attribute to zero (default) effectively disables gBondPmTca15MinUASCrossing notification. This object maps to the TR-159 attribute aGroupPerfThreshold15MinUAS." REFERENCE "[TR-159] 5.5.1.41" ::= { gBondPortPmTcaProfileEntry 4 } gBondPortPmTcaProfileThresh1DayES OBJECT-TYPE Beili & Morgenstern Expires January 17, 2013 [Page 53] Internet-Draft G.Bond MIB Jul 2012 SYNTAX GBondPm1DayIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A desired threshold for the number of Errored Seconds (ES) within any given 1-day performance data collection interval. If the number of ESs in a particular 1-day collection interval reaches or exceeds this value, a gBondPmTca1DayESCrossing notification MAY be generated if enabled by gBondPortConfPmTcaEnable. At most one notification can be sent per interval. Setting this attribute to zero (default) effectively disables gBondPmTca1DayESCrossing notification. This object maps to the TR-159 attribute aGroupPerfThreshold1DayES." REFERENCE "[TR-159] 5.5.1.51" ::= { gBondPortPmTcaProfileEntry 5 } gBondPortPmTcaProfileThresh1DaySES OBJECT-TYPE SYNTAX GBondPm1DayIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "A desired threshold for the number of Severely Errored Seconds (SES) within any given 1-day performance data collection interval. If the number of SESs in a particular 1-day collection interval reaches or exceeds this value, a gBondPmTca1DaySESCrossing notification MAY be generated if enabled by gBondPortConfPmTcaEnable. At most one notification can be sent per interval. Setting this attribute to zero (default) effectively disables gBondPmTca1DaySESCrossing notification. This object maps to the TR-159 attribute aGroupPerfThreshold1DaySES." REFERENCE "[TR-159] 5.5.1.52" ::= { gBondPortPmTcaProfileEntry 6 } gBondPortPmTcaProfileThresh1DayUAS OBJECT-TYPE SYNTAX GBondPm1DayIntervalThreshold UNITS "seconds" MAX-ACCESS read-create Beili & Morgenstern Expires January 17, 2013 [Page 54] Internet-Draft G.Bond MIB Jul 2012 STATUS current DESCRIPTION "A desired threshold for the number of Unavailable Seconds (UAS) within any given 1-day performance data collection interval. If the number of UASs in a particular 1-day collection interval reaches or exceeds this value, a gBondPmTca1DayUASCrossing notification MAY be generated if enabled by gBondPortConfPmTcaEnable. At most one notification can be sent per interval. Setting this attribute to zero (default) effectively disables gBondPmTca1DayUASCrossing notification. This object maps to the TR-159 attribute aGroupPerfThreshold1DayUAS." REFERENCE "[TR-159] 5.5.1.53" ::= { gBondPortPmTcaProfileEntry 7 } gBondPortPmTcaProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls the creation, modification, or deletion of the associated entry in the gBondPortPmTcaProfileTable per the semantics of RowStatus. If an 'active' entry is referenced via gBondPortConfPmTcaConfProfile instance(s), the entry MUST remain 'active'. An 'active' entry SHALL NOT be modified. In order to modify an existing entry, it MUST be taken out of service (by setting this object to 'notInService'), modified, and set 'active' again." ::= { gBondPortPmTcaProfileEntry 8 } -- The BCE group gBondBceConfTable OBJECT-TYPE SYNTAX SEQUENCE OF GBondBceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for Configuration of G.Bond common aspects for the Bonding Channel Entity (BCE) ports (modems/channels). Beili & Morgenstern Expires January 17, 2013 [Page 55] Internet-Draft G.Bond MIB Jul 2012 Entries in this table MUST be maintained in a persistent manner." ::= { gBondBce 1 } gBondBceConfEntry OBJECT-TYPE SYNTAX GBondBceConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond BCE Configuration table. Each entry represents common aspects of a G.Bond BCE port indexed by the ifIndex. Note that a G.Bond BCE port can be stacked below a single GBS port, also indexed by ifIndex, possibly together with other BCE ports if GAF is enabled." INDEX { ifIndex } ::= { gBondBceConfTable 1 } GBondBceConfEntry ::= SEQUENCE { gBondBceConfRemoteDiscoveryCode PhysAddress } gBondBceConfRemoteDiscoveryCode OBJECT-TYPE SYNTAX PhysAddress (SIZE(0|6)) MAX-ACCESS read-write STATUS current DESCRIPTION "A Remote Discovery Code of the BCE port at CO. A 6 octet long Discovery Code of the peer GBS connected via the BCE. Reading this object results in a Discovery Get operation. Setting this object to all zeroes results in a Discovery Clear_if_Same operation (the value of gBondPortConfDiscoveryCode at the peer GBS SHALL be the same as gBondPortConfDiscoveryCode of the local GBS associated with the BCE for the operation to succeed). Writing a non-zero value to this object results in a Discovery Set_if_Clear operation. A zero-length octet string SHALL be returned on an attempt to read this object when GAF aggregation is not enabled. This object is irrelevant in BCE-R port subtypes (CPE side): in this case a zero length octet string SHALL be returned on an attempt to read this object, an attempt to change this object MUST be rejected (in case of SNMP with the error inconsistentValue). Discovery MUST be performed when the link is Down. Beili & Morgenstern Expires January 17, 2013 [Page 56] Internet-Draft G.Bond MIB Jul 2012 Attempts to change this object MUST be rejected (in case of SNMP with the error inconsistentValue), If the link is Up or Initializing. This object maps to the TR-159 attribute aLineRemoteDiscoveryCode." REFERENCE "[TR-159] 5.5.6.7" ::= { gBondBceConfEntry 1 } -- -- Conformance Statements -- gBondGroups OBJECT IDENTIFIER ::= { gBondConformance 1 } gBondCompliances OBJECT IDENTIFIER ::= { gBondConformance 2 } -- Object Groups gBondBasicGroup OBJECT-GROUP OBJECTS { gBondPortStatOperScheme, gBondPortStatUpDataRate, gBondPortStatDnDataRate, gBondPortConfTargetUpDataRate, gBondPortConfTargetDnDataRate, gBondPortCapSchemesSupported, gBondPortCapCapacity, gBondPortStatNumBCEs, gBondPortStatSide, gBondPortStatFltStatus } STATUS current DESCRIPTION "A collection of objects representing management information common to all types of G.Bond ports." ::= { gBondGroups 1 } gBondDiscoveryGroup OBJECT-GROUP OBJECTS { gBondPortStatPeerOperScheme, gBondPortCapPeerSchemesSupported, gBondPortCapPeerCapacity, gBondPortConfDiscoveryCode, gBondBceConfRemoteDiscoveryCode } STATUS current Beili & Morgenstern Expires January 17, 2013 [Page 57] Internet-Draft G.Bond MIB Jul 2012 DESCRIPTION "A collection of objects supporting OPTIONAL G.Bond discovery in G.Bond ports." ::= { gBondGroups 2 } gBondMultiSchemeGroup OBJECT-GROUP OBJECTS { gBondPortConfAdminScheme, gBondPortConfPeerAdminScheme } STATUS current DESCRIPTION "A collection of objects providing OPTIONAL management information for G.Bond ports supporting multiple bonding schemes." ::= { gBondGroups 3 } gBondTcaConfGroup OBJECT-GROUP OBJECTS { gBondPortConfThreshLowUpRate, gBondPortConfThreshLowDnRate, gBondPortConfLowRateCrossingEnable } STATUS current DESCRIPTION "A collection of objects required for configuration of alarm thresholds and notifications in G.Bond ports." ::= { gBondGroups 4 } gBondTcaNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { gBondLowUpRateCrossing, gBondLowDnRateCrossing } STATUS current DESCRIPTION "This group supports notifications of significant conditions (non-PM threshold crossing alerts) associated with G.Bond ports." ::= { gBondGroups 5 } gBondPmCurGroup OBJECT-GROUP OBJECTS { gBondPortPmCurES, gBondPortPmCurSES, gBondPortPmCurUAS, gBondPortPmCur15MinValidIntervals, gBondPortPmCur15MinInvalidIntervals, gBondPortPmCur15MinTimeElapsed, Beili & Morgenstern Expires January 17, 2013 [Page 58] Internet-Draft G.Bond MIB Jul 2012 gBondPortPmCur15MinES, gBondPortPmCur15MinSES, gBondPortPmCur15MinUAS, gBondPortPmCur1DayValidIntervals, gBondPortPmCur1DayInvalidIntervals, gBondPortPmCur1DayTimeElapsed, gBondPortPmCur1DayES, gBondPortPmCur1DaySES, gBondPortPmCur1DayUAS } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL current Performance Monitoring information for G.Bond ports." ::= { gBondGroups 6 } gBondPm15MinGroup OBJECT-GROUP OBJECTS { gBondPortPm15MinIntervalMoniTime, gBondPortPm15MinIntervalES, gBondPortPm15MinIntervalSES, gBondPortPm15MinIntervalUAS, gBondPortPm15MinIntervalValid } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL historical Performance Monitoring information for G.Bond ports, during previous 15-minute intervals ." ::= { gBondGroups 7 } gBondPm1DayGroup OBJECT-GROUP OBJECTS { gBondPortPm1DayIntervalMoniTime, gBondPortPm1DayIntervalES, gBondPortPm1DayIntervalSES, gBondPortPm1DayIntervalUAS, gBondPortPm1DayIntervalValid } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL historical Performance Monitoring information for G.Bond ports, during previous 1-day intervals ." ::= { gBondGroups 8 } gBondPmTcaConfGroup OBJECT-GROUP OBJECTS { Beili & Morgenstern Expires January 17, 2013 [Page 59] Internet-Draft G.Bond MIB Jul 2012 gBondPortConfPmTcaConfProfile, gBondPortConfPmTcaEnable, gBondPortPmTcaProfileThresh15MinES, gBondPortPmTcaProfileThresh15MinSES, gBondPortPmTcaProfileThresh15MinUAS, gBondPortPmTcaProfileThresh1DayES, gBondPortPmTcaProfileThresh1DaySES, gBondPortPmTcaProfileThresh1DayUAS, gBondPortPmTcaProfileRowStatus } STATUS current DESCRIPTION "A collection of objects required for configuration of Performance Monitoring Threshold Crossing Alert notifications in G.Bond ports." ::= { gBondGroups 9 } gBondPmTcaNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { gBondPmTca15MinESCrossing, gBondPmTca15MinSESCrossing, gBondPmTca15MinUASCrossing, gBondPmTca1DayESCrossing, gBondPmTca1DaySESCrossing, gBondPmTca1DayUASCrossing } STATUS current DESCRIPTION "This group supports notifications of performance monitoring thresholds crossing alerts associated with G.Bond ports." ::= { gBondGroups 10 } -- Compliance Statements gBondCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for G.Bond interfaces. Compliance with the following external compliance statements is REQUIRED: MIB Module Compliance Statement ---------- -------------------- IF-MIB ifCompliance3 Compliance with the following external compliance statements is OPTIONAL for implementations supporting bonding with flexible cross-connect between the GBS and BCE ports: Beili & Morgenstern Expires January 17, 2013 [Page 60] Internet-Draft G.Bond MIB Jul 2012 MIB Module Compliance Statement ---------- -------------------- IF-INVERTED-STACK-MIB ifInvCompliance IF-CAP-STACK-MIB ifCapStackCompliance" MODULE -- this module MANDATORY-GROUPS { gBondBasicGroup, gBondTcaConfGroup, gBondTcaNotificationGroup } GROUP gBondDiscoveryGroup DESCRIPTION "Support for this group is only required for implementations supporting G.Bond Discovery function." GROUP gBondMultiSchemeGroup DESCRIPTION "Support for this group is only required for implementations supporting multiple bonding schemes." GROUP gBondPmCurGroup DESCRIPTION "Support for this group is only required for implementations supporting Performance Monitoring." GROUP gBondPm15MinGroup DESCRIPTION "Support for this group is only required for implementations supporting 15-min historical Performance Monitoring." GROUP gBondPm1DayGroup DESCRIPTION "Support for this group is only required for implementations supporting 1-day historical Performance Monitoring." GROUP gBondPmTcaConfGroup DESCRIPTION "Support for this group is only required for implementations supporting Performance Monitoring Threshold Crossing Alert notifications." GROUP gBondPmTcaNotificationGroup DESCRIPTION "Support for this group is only required for implementations supporting Performance Monitoring Threshold Crossing Alert notifications." Beili & Morgenstern Expires January 17, 2013 [Page 61] Internet-Draft G.Bond MIB Jul 2012 OBJECT gBondPortCapSchemesSupported SYNTAX IANAgBondSchemeList DESCRIPTION "Support for all bonding Schemes types is not required. However at least one value SHALL be supported" OBJECT gBondPortCapPeerSchemesSupported SYNTAX IANAgBondSchemeList DESCRIPTION "Support for all bonding Schemes types is not required. However at least one value SHALL be supported" ::= { gBondCompliances 1 } END 7. IANA-maintained G.Bond TC Definitions IANA-GBOND-TC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC ; ------------------------------------------------------------------------ ianaGBondTcMIB MODULE-IDENTITY LAST-UPDATED "201207160000Z" -- July 16, 2012 ORGANIZATION "IANA" CONTACT-INFO " Internet Assigned Numbers Authority Postal: ICANN 4676 Admiralty Way, Suite 330 Marina del Rey, CA 90292 Tel: +1-310-823-9358 EMail: iana@iana.org" DESCRIPTION "This MIB module defines IANAgBondScheme and IANAgBondSchemeList TEXTUAL-CONVENTIONs, specifying enumerated values of the gBondPortConfAdminScheme, gBondPortConfPeerAdminScheme, gBondPortStatOperScheme, gBondPortStatPeerOperScheme and gBondPortCapSchemesSupported, gBondPortCapPeerSchemesSupported objects respectively, defined in the GBOND-MIB. It is intended that each new bonding scheme defined by the Beili & Morgenstern Expires January 17, 2013 [Page 62] Internet-Draft G.Bond MIB Jul 2012 ITU-T Q4/SG15 working group and approved for publication in a revision of ITU-T G.998 specification will be added to this MIB module, provided that it is suitable for being managed by the base objects in the GBOND-MIB. An Expert Review, as defined in RFC 5226 [RFC5226], is REQUIRED for such additions. The following references are used throughout this MIB module: [G.998.1] refers to: ITU-T Recommendation G.998.1: 'ATM-based multi-pair bonding', January 2005. [G.998.2] refers to: ITU-T Recommendation G.998.2: 'Ethernet-based multi-pair bonding', January 2005. [G.998.3] refers to: ITU-T Recommendation G.998.3: 'Multi-pair bonding using time-division inverse multiplexing', January 2005. Naming Conventions: BCE - Bonding Channel Entity GBS - Generic Bonding Sublayer These references should be updated as appropriate when a new bonding scheme is added to this MIB module. Copyright (C) The IETF Trust (2012). The initial version of this MIB module was published in RFC XXXX; for full legal notices see the RFC itself. Supplementary information may be available at: http://www.ietf.org/copyrights/ianamib.html" REVISION "201207160000Z" -- Jul 16, 2012 DESCRIPTION "Initial version, published as RFC XXXX." -- EdNote: Replace XXXX with the actual RFC number & -- remove this note ::= { mib-2 ZZZ } -- EdNote: Replace ZZZ with a real OID once it is -- allocated & remove this note. -- Textual Conventions IANAgBondSchemeList ::= TEXTUAL-CONVENTION STATUS current Beili & Morgenstern Expires January 17, 2013 [Page 63] Internet-Draft G.Bond MIB Jul 2012 DESCRIPTION "This textual convention defines a bitmap of possible ITU-T G.998 (G.Bond) bonding schemes. Currently the following values are defined for the corresponding bonding schemes: g9981(1) - G.998.1, (G.Bond/ATM, see G9981-MIB) g9982(2) - G.998.2, (G.Bond/Ethernet, see G9982-MIB) g9983(3) - G.998.3, (G.Bond/TDIM, see G9983-MIB) An additional value of none(0), can be returned as a result of GET operation, when an value of the object cannot be determined (for example a peer GBS cannot be reached), the port does not support any kind of bonding or when a single-BCE G.998.2 GBS supports bonding (frame fragmentation/reassembly) bypass." SYNTAX BITS { none(0), g9981(1), g9982(2), g9983(3) } IANAgBondScheme ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention defines ITU-T G.998 bonding scheme values. Possible values are: none(0) - no bonding (e.g. on single-BCE G.998.2 GBS) or unknown g9981(1) - G.998.1 (G.Bond/ATM) g9982(2) - G.998.2 (G.Bond/Ethernet) g9983(3) - G.998.3 (G.Bond/TDIM)." SYNTAX INTEGER { none(0), g9981(1), g9982(2), g9983(3) } END 8. Security Considerations There is a number of managed objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: Beili & Morgenstern Expires January 17, 2013 [Page 64] Internet-Draft G.Bond MIB Jul 2012 o Changing of gBondPortConfAdminScheme may lead to a potential locking of the link, if the peer device does not support desired bonding scheme. o Changing of gBondPortConfDiscoveryCode, before the discovery operation, may lead to a wrongful discovery, for example when two CO ports are connected to the same multi-channel RT port, while both CO ports have the same discovery register value. o Changing of target upstream/downstream data rate via gBondPortConfTargetUpDataRate/gBondPortConfTargetDnDataRate may lead to anything from link quality and rate degradation to a complete link initialization failure, as ability of a G.Bond port to support a particular configuration depends on the copper environment. o Activation of a specific line/channel may cause a severe degradation of service for another G.Bond port, whose channel(s) may be affected by the cross-talk from the newly activated channel. o Removal of a channel from an operationally 'up' G.Bond port, aggregating several channels, may cause port's rate degradation Some of the readable objects in this MIB module (i.e., those with MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments since, collectively, they provide information about the performance of network interfaces and can reveal some aspects of their configuration. In particular, since a bonded xDSL port can be comprised of multiple Unshielded Twisted Pair (UTP) voice grade copper, located in the same bundle with other pairs belonging to another operator/customer, it is theoretically possible to eavesdrop to a G.Bond transmission, simply by "listening" to a cross-talk from the bonded pairs, especially if the operating parameters of the G.Bond link in question are known. It is thus important to control even GET and/or NOTIFY access to these objects and possibly even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o gBondPortStatTable - objects in this table provide status information for the G.Bond port, which may aid in identification of the pairs belonging to the bonded port and eavesdroping to the traffic over that port. SNMP versions prior to SNMPv3 did not include adequate security. Beili & Morgenstern Expires January 17, 2013 [Page 65] Internet-Draft G.Bond MIB Jul 2012 Even if the network itself is secure (for example by using IPSec), there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. Implementations MUST provide the security features described by the SNMPv3 framework (see [RFC3410]), including full support for authentication and privacy via the User-based Security Model (USM) [RFC3414] with the AES cipher algorithm [RFC3826]. Implementations MAY also provide support for the Transport Security Model (TSM) [RFC5591] in combination with a secure transport such as SSH [RFC5592] or TLS/DTLS [RFC6353]. Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 9. IANA Considerations Three new values of IANAifType: g9981(263), g9982(264) and g9983(265) have been allocated by IANA [1] in the IANAifType-MIB module [IANAifType-MIB]. An object identifier for gBondMIB MODULE-IDENTITY SHALL be allocated by IANA in the MIB-2 transmission sub-tree, before this document is published. This document defines the first version of the IANA-maintained IANA- GBOND-MIB module. It is intended that each new G.998 bonding scheme defined by the ITU-T Q4/SG15 working group and approved for publication in a revision of ITU-T G.998.x is added to the IANA- maintaned MIB module, provided that it is suitable for being managed by the base objects in the GBOND-MIB module. For each new bonding scheme added, a short description of the bonding protocol and, wherever possible, a reference to a publicly available specification SHOULD be specified. An Expert Review, as defined in [RFC5226]., is REQUIRED, for each modification. 10. Acknowledgments This document was produced by the [ADSLMIB] working group. Special thanks to Dan Romascanu for his meticulous review of this Beili & Morgenstern Expires January 17, 2013 [Page 66] Internet-Draft G.Bond MIB Jul 2012 text. 11. References 11.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002. [RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", STD 62, RFC 3414, December 2002. [RFC3705] Ray, B. and R. Abbi, "High Capacity Textual Conventions for MIB Modules Using Performance Beili & Morgenstern Expires January 17, 2013 [Page 67] Internet-Draft G.Bond MIB Jul 2012 History Based on 15 Minute Intervals", RFC 3705, February 2004. [RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The Advanced Encryption Standard (AES) Cipher Algorithm in the SNMP User-based Security Model", RFC 3826, June 2004. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [TR-159] Beili, E. and M. Morgenstern, "Management Framework for xDSL Bonding", Broadband Forum technical report TR-159, December 2008. 11.2. Informative References [802.3] IEEE, "IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications", IEEE Std 802.3- 2005, December 2005. [ADSLMIB] IETF, "ADSL MIB (adslmib) Charter", . [G.991.2] ITU-T, "Single-pair High-speed Digital Subscriber Line (SHDSL) transceivers", ITU-T Recommendation G.991.2, December 2003, . Beili & Morgenstern Expires January 17, 2013 [Page 68] Internet-Draft G.Bond MIB Jul 2012 [G.993.1] ITU-T, "Very High speed Digital Subscriber Line transceivers", ITU-T Recommendation G.993.1, June 2004, . [G.994.1] ITU-T, "Handshake procedures for digital subscriber line (DSL) transceivers", ITU-T Recommendation G.994.1, February 2007, . [G.998.1] ITU-T, "ATM-based multi-pair bonding", ITU-T Recommendation G.998.1, January 2005, . [G.998.2] ITU-T, "Ethernet-based multi-pair bonding", ITU-T Recommendation G.998.2, January 2005, . [G.998.3] ITU-T, "Multi-pair bonding using time-division inverse multiplexing", ITU-T Recommendation G.998.3, January 2005, . [I-D.ietf-adslmib-gbond-atm-mib] Beili, E., "ATM-based xDSL Bonded Interfaces MIB", draft-ietf- adslmib-gbond-atm-mib-06 (work in progress), March 2012. [I-D.ietf-adslmib-gbond-eth-mib] Beili, E. and M. Morgenstern, "Ethernet-based xDSL Bonded Interfaces MIB", draft-ietf- adslmib-gbond-eth-mib-07 (work in progress), July 2012. [I-D.ietf-adslmib-gbond-tdim-mib] Beili, E., "TDIM-based xDSL Bonded Interfaces MIB", draft-ietf- adslmib-gbond-tdim-mib-08 (work in progress), March 2012. Beili & Morgenstern Expires January 17, 2013 [Page 69] Internet-Draft G.Bond MIB Jul 2012 [IANAifType-MIB] Internet Assigned Numbers Authority (IANA), "IANAifType Textual Convention definition", . [RFC2790] Waldbusser, S. and P. Grillo, "Host Resources MIB", RFC 2790, March 2000. [RFC2864] McCloghrie, K. and G. Hanson, "The Inverted Stack Table Extension to the Interfaces Group MIB", RFC 2864, June 2000. [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002. [RFC3440] Ly, F. and G. Bathrick, "Definitions of Extension Managed Objects for Asymmetric Digital Subscriber Lines", RFC 3440, December 2002. [RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3593, September 2003. [RFC3728] Ray, B. and R. Abbi, "Definitions of Managed Objects for Very High Speed Digital Subscriber Lines (VDSL)", RFC 3728, February 2004. [RFC4181] Heard, C., "Guidelines for Authors and Reviewers of MIB Documents", BCP 111, RFC 4181, September 2005. [RFC4319] Sikes, C., Ray, B., and R. Abbi, "Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line Beili & Morgenstern Expires January 17, 2013 [Page 70] Internet-Draft G.Bond MIB Jul 2012 (SHDSL) Lines", RFC 4319, December 2005. [RFC4706] Morgenstern, M., Dodge, M., Baillie, S., and U. Bonollo, "Definitions of Managed Objects for Asymmetric Digital Subscriber Line 2 (ADSL2)", RFC 4706, November 2006. [RFC5066] Beili, E., "Ethernet in the First Mile Copper (EFMCu) Interfaces MIB", RFC 5066, November 2007. [RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model for the Simple Network Management Protocol (SNMP)", RFC 5591, June 2009. [RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure Shell Transport Model for the Simple Network Management Protocol (SNMP)", RFC 5592, June 2009. [RFC5650] Morgenstern, M., Baillie, S., and U. Bonollo, "Definitions of Managed Objects for Very High Speed Digital Subscriber Line 2 (VDSL2)", RFC 5650, September 2009. [RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network Time Protocol Version 4: Protocol and Algorithms Specification", RFC 5905, June 2010. [RFC6353] Hardaker, W., "Transport Layer Security (TLS) Transport Model for the Simple Network Management Protocol (SNMP)", RFC 6353, July 2011. [af-phy-0086] ATM Forum, "Inverse Multiplexing for ATM (IMA) Specification Version 1.1", ATM Forum specification af-pfy-0086.001, Beili & Morgenstern Expires January 17, 2013 [Page 71] Internet-Draft G.Bond MIB Jul 2012 March 1999. URIs [1] Authors' Addresses Edward Beili Actelis Networks 25 Bazel St. Petach-Tikva 49103 Israel Phone: +972-3-924-3491 EMail: edward.beili@actelis.com Moti Morgenstern ECI Telecom 30 Hasivim St. Petach-Tikva 4951169 Israel Phone: +972-3-926-6258 EMail: moti.morgenstern@ecitele.com Beili & Morgenstern Expires January 17, 2013 [Page 72]